User Panel
User Panel
User Panel
|
Posted: 6/21/2016 1:25:47 PM EDT
[#1]
how much play do you have in the actual hook side by side?
if none.....just bend it over to rub against the bolt slightly.......and if it is angled on the nose.....test fire...if the spent case stovepipes or just doesn't clear the port....square the nose of the hook. |
|
|
|
Posted: 6/21/2016 4:10:25 PM EDT
[#2]
Rudy... its moves a pretty good bit in the channel on the bolt... more than I would like... that is what is allowing the case head to ping off and push it to the side without ejecting...
|
|
|
|
Posted: 6/21/2016 5:37:45 PM EDT
[#3]
This is the topload block, yes.....? The did a redesign on them and tightened them up.....they have two small springs in them....if you take ie apart and replace or stretch the springs it may snug it up....otherwise I'd put a shim in....Just found one of the toploads under the pile on my desk....let me see if I can find a box of parts I had where I cannibalized a bunch for 45 prototypes..;...might have something to square you a way if I can find the box.
|
|
|
|
Posted: 6/21/2016 5:41:31 PM EDT
[#4]
The ejector on the PSA Colt style lower should move very little. Can you snap a picture of the ejector arm looking down onto the top of the lower receiver? Also check to make sure PSA installed the split roll pin through the side of the lower receiver to hold the ejector assembly in place. The end of the pin should be visible while looking into the hole on the left side of the lower, just forward of the bolt catch.
|
|
|
|
Posted: 6/21/2016 5:45:23 PM EDT
[#5]
Quote HistoryQuoted:
What holds it in...set screw or roll pin? Rudy, the PSA ejector parts look very similar to the CMMG MK9 ejctor. Google CMMG MK9 ejector kit to see what I mean. Held in by a split roll pin. |
|
|
|
Posted: 6/21/2016 5:45:57 PM EDT
[#6]
Just noticed you be a fellow Georgia boy.....how fer is ya from Macon....?
If you can swing by the shop....pretty sure I can square you away.... |
|
|
|
Posted: 6/21/2016 5:47:54 PM EDT
[#7]
I will pop pics tonight
|
|
|
|
Posted: 6/21/2016 6:02:32 PM EDT
[#8]
Is it a dedicated lower or a lower and a mag block
|
|
|
|
Posted: 6/21/2016 6:03:05 PM EDT
[#9]
Just saw Rudy's response to you and reread your original post. Is this the newer PSA Colt style lower or the older lower with the mag block installed? My comments were referring to the newer dedicated lower. Sorry if I'm pointing you in the wrong direction.
Dave |
|
|
|
Posted: 6/21/2016 6:14:55 PM EDT
[#10]
mag block installed.... and..Rudy... I am in Milledgeville... and will prolly be over in Macon Thursday... how is your schedule?
|
|
|
|
Posted: 6/21/2016 6:18:19 PM EDT
[#11]
It is one of the lower deals on special a few months ago with the colt style block installed for $159. I bought it.. and stuck it to the side for when I picked up an upper. Finally got and upper and put it together... and now the problem....
|
|
|
|
Posted: 6/21/2016 6:27:15 PM EDT
[#12]
|
|
|
|
Posted: 6/21/2016 7:09:30 PM EDT
[#13]
Ok...no magblock...dedicated lower.....simple fix...piece of steel shim stock inserted with the ejector to lock the position....just need to get an accurate width of the ejector and of the slot.....and if pushing it all the way to one side of the pocket solves the issue.
|
|
|
|
Posted: 6/22/2016 9:20:47 AM EDT
[#14]
Quote HistoryQuoted:
mag block installed.... and..Rudy... I am in Milledgeville... and will prolly be over in Macon Thursday... how is your schedule? Brought yourself on....shoot me an email and I'll send address and phone for shop......what time are yo thinking? |
|
|
|
Posted: 6/24/2016 8:28:25 PM EDT
[#15]
Had a chance to get it out to the range for an extended session??????
|
|
|
|
Posted: 6/24/2016 8:29:49 PM EDT
[#16]
Double tap
|
|
|
|
Posted: 6/25/2016 2:21:33 PM EDT
[#17]
Hey Rudy! Not yet... that's the plan for tomorrow... I DEF want to thank you again for getting me running... It was awesome to meet you and tap your knowledge of our hobby. Not to mention, show and tell... I am FIRED UP!! Thanks again for treating me with true Southern hospitality!!
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
