User Panel
Posted: 1/20/2010 11:17:45 AM EDT
Has anyone done one of these since 12/1/09? Apparently spec's have changed and instead of threading the buffer the fcg well is solid. The building process now involves drilling and milling out that well in addition to the previous norm of drilling the necessery holes in the receiver blank.
Is this more difficult that the previous versions? Any comments or problems anyone has encountered? I'd like to try one, advice or suggestions? Thanks. |
|
Buy your 80%'s from Tactical Machining, i've done a few of them.
Much easier than before (less jigging / steps), but there is more milling to do. Before the requirements changed, i used AR15PLUS.com, but now they've caught up with times and are selling compliant lowers. They're just twice as much for more work and lower quality, in my opinion... Mill the FCG pocket, and rear lug pocket Mill the trigger slot Drill the TWO holes (trigger/hammer) and you're done! They're pretty nice too... |
|
Sweet!
Have fun, (and take your sweet time...) Do you have an AR Lower print? Comes in handy... If not, got here and download from the "Blueprints" section: CNC GUNS |
|
I've never taken one to be anodized, but you could. I usually soda-blast, acetone and Duracoat. Works just fine on the blasted surface, including inside the pin holes. If you want to have it anodized you'll have to be there or have a firearms anodizer do it (once you complete it, it's a firearm and must be transferred as such, unless you're actually there)... Some people have had luck with the home-anodizing kits, but i've never played with one...
|
|
Silly me, it's in the web site, they're anodized at the factory. Need to read all the stuff before I post.
|
|
Quoted:
Silly me, it's in the web site, they're anodized at the factory. Need to read all the stuff before I post. Well not sure what you mean, finished or 80%... Finished, stripped lowers are factory anodized. 80% lowers are bare aluminum when you get them... |
|
Quoted:
Silly me, it's in the web site, they're anodized at the factory. Need to read all the stuff before I post. Anodizing is surface treatment so your milling would remove it in those areas so the above poster is right. |
|
I ordered the tools, bits and mill and they've come in, downloaded the blueprint and printed out a blownup copy, I've got a couple of cans of wd-40 for cutting fluid. And, have gone through the tutorial on cnc guns website. I'm ready!!
Thank you all for your advice, I''ll update this as I go along... |
|
Does anyone know when tactical machining will have more 80% lowers in? I emailed them about it but haven't heard back yet.
|
|
educate me...what is the benefit of this? seems like a lot of work for something i can buy 100% complete.
|
|
Quoted:
I ordered the tools, bits and mill and they've come in, downloaded the blueprint and printed out a blownup copy, I've got a couple of cans of wd-40 for cutting fluid. And, have gone through the tutorial on cnc guns website. I'm ready!! Thank you all for your advice, I''ll update this as I go along... I'd trade the WD40 for some cutting/tapping fluid or some cheap gear oil.... WD40 doesn't make the best cutting fluid, it's too light and vaporizes quickly. TXGUNNER, It's the idea of completing something yourself for some, and the lack of paperwork for others... If i'm going to try something crazy with a design, which i do a lot of, i don't want to ruin a registered firearm to do it. (Such as the bufferless pistols or the .45 lower i built for $80, instead of $300 for a factory .45 lower...) |
|
Quoted:
Does anyone know when tactical machining will have more 80% lowers in? I emailed them about it but haven't heard back yet. Call them, they've always answered for me and that's how i ordered my lowers... |
|
one reason to do it and the reason I will be getting one in the near future is to get around asinine laws. In Ca you can only buy handguns on approved lists. there are no AR pistols on these lists so if you want one you have to jump through alot of loopholes to get a pistol registered lower. The easiest to do BY FAR is to build an 80% lower yourself.
|
|
Just wondering what mill people use, I have heard not to get from Harbor Freight, and that Grizzly is good, but what model say from Grizzly is best for this job. I don't intend to use it for things other than firearms and that size or scope? Any recommendations will be appreciated.
|
|
Quoted:
Just wondering what mill people use, I have heard not to get from Harbor Freight, and that Grizzly is good, but what model say from Grizzly is best for this job. I don't intend to use it for things other than firearms and that size or scope? Any recommendations will be appreciated. I've got a full-sized Bridgeport mill, but i've heard good things about the Grizzly.... If you're using the smaller mills, i would recommend the 80% jig from Tactical Machining as well, just to simplify the jigging... |
|
Harbor Freight and Grizzley are the same machine, made by Seig (China). Whichever you can get the best price + shipping (these are heavy). HF was free shipping when I bought mine. CNC Gunsmithing has a forum all about machining lowers, etc.
|
|
Thank you for the heads up on cutting fluid, I'll be looking into that.
Good question concerning 'why go to all the trouble for something I can buy.' I can only speak for myself and two of my friends. We just finished building 3 ak's from Romanian parts kits. We bought the receivers but learned alot about furniture refinishing, riviting, knocking out stubborn barrel pins, blueing and pressing/installing barrels. When we finished the builds we looked at each othe and said that was fun lets not stop now. So this 80% ar receiver is our next project. We're doing it for a sense of accomplishment, as a hobby and for the pride of doing something not many other people have done. We're definitly not saving money. Just my two cents, thank you everyone for your remarks. |
|
Quoted:
Buy your 80%'s from Tactical Machining, i've done a few of them. Much easier than before (less jigging / steps), but there is more milling to do. Before the requirements changed, i used AR15PLUS.com, but now they've caught up with times and are selling compliant lowers. They're just twice as much for more work and lower quality, in my opinion... http://www.tacticalmachining.com/images/372_247_80-lower.jpg Mill the FCG pocket, and rear lug pocket Mill the trigger slot Drill the TWO holes (trigger/hammer) and you're done! They're pretty nice too... You need to drill for the buffer tube retainer pin also. |
|
Quoted:
Quoted:
Buy your 80%'s from Tactical Machining, i've done a few of them. Much easier than before (less jigging / steps), but there is more milling to do. Before the requirements changed, i used AR15PLUS.com, but now they've caught up with times and are selling compliant lowers. They're just twice as much for more work and lower quality, in my opinion... http://www.tacticalmachining.com/images/372_247_80-lower.jpg Mill the FCG pocket, and rear lug pocket Mill the trigger slot Drill the TWO holes (trigger/hammer) and you're done! They're pretty nice too... You need to drill for the buffer tube retainer pin also. Not on the ones i ordered.... and from their website: "The operations left to be completed are as follows: fire control group, trigger pin, hammer pin, trigger slot." |
|
Sweet. I'm hoping to do this when I get home. I hope they have some .308 80% er's in stock soon.
|
|
I've read somewhere on the ARFCOM that some alphabet agency loves to wander through the customer database of 80% lowers sellers..
|
|
I buy my 80% AR15 and AR10 from www.ar15jigs.com they also have the jigs.
|
|
Quoted:
What jig are you guys using for your milling? I just use my mill vise and some 1-2-3 blocks, but i'm using a bridgeport and not a dremel and a drill press... Quoted:
I buy my 80% AR15 and AR10 from www.ar15jigs.com they also have the jigs. That's a pretty good price for billet "75%" lowers, but a good bit more work. If you've got a mill, it wouldn't be bad though... |
|
Tactical now also sells their own jigs for finishing these using a drill press.
|
|
|
I have access to manual and CNC mills as well as knowledge on how to use SolidWorks so that's why I asked, I'd really only need the best way to clamp the receiver without marring the finish. Thanks guys
|
|
Quoted:
I have access to manual and CNC mills as well as knowledge on how to use SolidWorks so that's why I asked, I'd really only need the best way to clamp the receiver without marring the finish. Thanks guys I'm partial to Solidworks as well, use it everyday. As far as marring the finish, there IS no finish, until you finish it I usually clamp up on the grip triangle area to mill the FCG pocket, since it's fairly solid, and then use aluminum blocks to clamp the receiver in the mill vice sideways to drill the trigger and hammer pins. |
|
Quoted:
Quoted:
I have access to manual and CNC mills as well as knowledge on how to use SolidWorks so that's why I asked, I'd really only need the best way to clamp the receiver without marring the finish. Thanks guys I'm partial to Solidworks as well, use it everyday. As far as marring the finish, there IS no finish, until you finish it I usually clamp up on the grip triangle area to mill the FCG pocket, since it's fairly solid, and then use aluminum blocks to clamp the receiver in the mill vice sideways to drill the trigger and hammer pins. Yeah, SolidWorks is flat out awesome. I'm not the best at it, but I can do most things very well. It's fun just designing widgets and such :D |
|
Me and my buddies have built over 10 AR's from Tactical Machine 80% lowers. We started using the jig from CNCGunsmithing and a drill press but then I bought the HF mini mill (Seig x2 clone). I added a DRO to my mill and now can machine a lower in about 2 hours using the fixture and dimensions I got from the ray-vin tutorial.
You can not go wrong using Tactical machine's 80% IMHO |
|
Russ477, is your finish anodized, and if so, how did you do it or did someone else. It looks really good. I am working on an 80%, no idea on the finish.
|
|
Russ4777
Thanks for the info, have never heard of the product, nice to have a good option. |
|
OK this is peaking my interest, so I have a few questions for now.
1. The Mini-Mill someone mentioned from HF, could you link it? or is this it? Harbor Freight 2. Would the Mini-Mill work on Titanium 80% lowers? I'm sure it would be hard on the cutting tools but still wondering. 3. Since you are the maker could you have them engraved while they are 80% with serial Numbers and your info? 4. Can you send it off to be anodized? you are really only sending your lower to get done and back to you again. |
|
Quoted:
OK this is peaking my interest, so I have a few questions for now. 1. The Mini-Mill someone mentioned from HF, could you link it? or is this it? Harbor Freight 2. Would the Mini-Mill work on Titanium 80% lowers? I'm sure it would be hard on the cutting tools but still wondering. 3. Since you are the maker could you have them engraved while they are 80% with serial Numbers and your info? 4. Can you send it off to be anodized? you are really only sending your lower to get done and back to you again. Here is a good look at the HF style and grace in design and construction, portrayed in great detail: Home Gunsmith Forum I didn't check to see if it's the same model you're looking at, but the author details some of the many problems that can and will rise up and bite you in the butt if you buy one of the HF machines and jump right into machining lowers. |
|
Posted by GLADIO:
I've read somewhere on the ARFCOM that some alphabet agency loves to wander through the customer database of 80% lowers sellers.. The ATF has no legal right to access 80% lower sellers records without a warrant.. The sellers do not have an FFL and not subject to the oversight of the ATF without a warrant. They do however have a say in determining which partially machined lowers are firearms and which are not. |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.