User Panel
Posted: 3/12/2015 10:24:24 PM EDT
Looking for the cheapest 18650 LED light I can find. We are standardizing on them for our heavy use lights here.... Why do I want cheap? OK you busted me. The real reason is that my 3 year old daughter has recently become obsessed with flashlights and has blasted through a small mountain of AAs in our cheapo LED lights. She's getting upgraded to rechargeable and all my rechargeable flashlights use 18650s.
|
|
http://intl-outdoor.com/xintd-c8-v4-xml2-t6-18650-flashlight-p-308.html
|
|
Amazon has a bunch under $10, but battery and charger are extra.
|
|
AA Eneloops
18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. |
|
|
|
|
Quoted:
What do you call high power? Can anyone expand on this? View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 What do you call high power? Can anyone expand on this? I don't see many 18650 lights that put out less than 500 lumens on the top end. Lots of them are close to 1000. At that level the light puts out a huge amount of heat. Enough to burn someone. Unprotected cells would be extremely bad for a kid. You would ruin them as soon as they were over discharged the first time, if it didn't burn. |
|
Quoted:
What do you call high power? Can anyone expand on this? View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 What do you call high power? Can anyone expand on this? jmho it's not so much the light as it is th battery itself. while a meltdown isn;t very common when it happens it's not something i'd want a kid holding. lithium batts are still just a bit on the iffy side for me. |
|
Quoted:
I don't see many 18650 lights that put out less than 500 lumens on the top end. Lots of them are close to 1000. At that level the light puts out a huge amount of heat. Enough to burn someone. Unprotected cells would be extremely bad for a kid. You would ruin them as soon as they were over discharged the first time, if it didn't burn. View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 What do you call high power? Can anyone expand on this? I don't see many 18650 lights that put out less than 500 lumens on the top end. Lots of them are close to 1000. At that level the light puts out a huge amount of heat. Enough to burn someone. Unprotected cells would be extremely bad for a kid. You would ruin them as soon as they were over discharged the first time, if it didn't burn. So use protected cells. |
|
Quoted:
Quoted:
Quoted:
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 What do you call high power? Can anyone expand on this? I don't see many 18650 lights that put out less than 500 lumens on the top end. Lots of them are close to 1000. At that level the light puts out a huge amount of heat. Enough to burn someone. Unprotected cells would be extremely bad for a kid. You would ruin them as soon as they were over discharged the first time, if it didn't burn. So use protected cells. Repeatedly draining a lithium ion battery all the way down until the protection kicks in will kill the battery in short order. |
|
Quoted:
Repeatedly draining a lithium ion battery all the way down until the protection kicks in will kill the battery in short order. View Quote unless you are buying really, really, and did i mention really cheap ass Chinese lights all are going to have low voltage shutoff built into the driver circuit. the shutoff can be anywhere from 3.2-2.8v so the cell remains safe. |
|
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 I don't have any eneloops although I've heard you guys talking about them. Can you charge them and leave them charged for long periods (6mo-year)? Can they be substituted for any device that would normally hold the particular size? Are they damaged by leaving them discharged for a prolonged period? Any catches other than cost? Also I appreciate the replies. I honestly had not thought about the safety aspects of using the lithium. She likes to turn the light on and then forget about it until it dies which I could see being a fire hazard if she dropped it into her toy box or something and it overheated. |
|
Quoted:
I don't have any eneloops although I've heard you guys talking about them. Can you charge them and leave them charged for long periods (6mo-year)? Can they be substituted for any device that would normally hold the particular size? Are they damaged by leaving them discharged for a prolonged period? Any catches other than cost? Also I appreciate the replies. I honestly had not thought about the safety aspects of using the lithium. She likes to turn the light on and then forget about it until it dies which I could see being a fire hazard if she dropped it into her toy box or something and it overheated. View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
AA Eneloops 18650 are too dangerous for kids. Especially in a high power light. Eneloops won't explode when discharged too fast. this x1000 I don't have any eneloops although I've heard you guys talking about them. Can you charge them and leave them charged for long periods (6mo-year)? Can they be substituted for any device that would normally hold the particular size? Are they damaged by leaving them discharged for a prolonged period? Any catches other than cost? Also I appreciate the replies. I honestly had not thought about the safety aspects of using the lithium. She likes to turn the light on and then forget about it until it dies which I could see being a fire hazard if she dropped it into her toy box or something and it overheated. I don't know about leaving them discharged but they are famous for holding a charge over years. They have very low self discharge rates. Use them in place of any AA battery. |
|
Cause 3: Over-discharged.
Applications without over-discharge preventing device can cause batteries to over-discharge. For example, use low current draw LED light until battery runs out, it cause over-discharge and later cannot charge the battery correctly. Recharging battery 2-3 times solves this problem but if the problem still persists, It is considered battery’ s life span has ended and please stop using. Continuous over-discharging causes damage to the batteries. We recommend to recharge the battery, once luminous energy become low or battery energy become low during using LED light they will maintain 75-80% of charge after 3 years if no use. http://panasonic.net/energy/eneloop/pdf/eneloop_handbook.pdf |
|
for her just getting the cheapest nicad rechargeables you can find might be best. they are not that expensive compared to alkalines and if you get 20 charges out of them before she kills them you come out ahead.
would also be a good time to teach her about responsibility such as turning thigs off properly and taking care of it. |
|
Quoted:
for her just getting the cheapest nicad rechargeables you can find might be best. they are not that expensive compared to alkalines and if you get 20 charges out of them before she kills them you come out ahead. would also be a good time to teach her about responsibility such as turning thigs off properly and taking care of it. View Quote I think this is the most prudent. |
|
Quoted:
for her just getting the cheapest nicad rechargeables you can find might be best. they are not that expensive compared to alkalines and if you get 20 charges out of them before she kills them you come out ahead. would also be a good time to teach her about responsibility such as turning thigs off properly and taking care of it. View Quote Oh yes... We are on that part hard. |
|
Quoted:
Cause 3: Over-discharged. Applications without over-discharge preventing device can cause batteries to over-discharge. For example, use low current draw LED light until battery runs out, it cause over-discharge and later cannot charge the battery correctly. Recharging battery 2-3 times solves this problem but if the problem still persists, It is considered battery’ s life span has ended and please stop using. Continuous over-discharging causes damage to the batteries. We recommend to recharge the battery, once luminous energy become low or battery energy become low during using LED light View Quote I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. |
|
Quoted:
I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. View Quote View All Quotes View All Quotes Quoted:
Quoted:
Cause 3: Over-discharged. Applications without over-discharge preventing device can cause batteries to over-discharge. For example, use low current draw LED light until battery runs out, it cause over-discharge and later cannot charge the battery correctly. Recharging battery 2-3 times solves this problem but if the problem still persists, It is considered battery’ s life span has ended and please stop using. Continuous over-discharging causes damage to the batteries. We recommend to recharge the battery, once luminous energy become low or battery energy become low during using LED light I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. OK so other than remove the battery and check it with a volt meter after each use how do you propose a person uses rechargeable battery that won't damage it? |
|
Quoted:
OK so other than remove the battery and check it with a volt meter after each use how do you propose a person uses rechargeable battery that won't damage it? View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
Cause 3: Over-discharged. Applications without over-discharge preventing device can cause batteries to over-discharge. For example, use low current draw LED light until battery runs out, it cause over-discharge and later cannot charge the battery correctly. Recharging battery 2-3 times solves this problem but if the problem still persists, It is considered battery’ s life span has ended and please stop using. Continuous over-discharging causes damage to the batteries. We recommend to recharge the battery, once luminous energy become low or battery energy become low during using LED light I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. OK so other than remove the battery and check it with a volt meter after each use how do you propose a person uses rechargeable battery that won't damage it? Steal her light from her every few days and charge it up! LOL! |
|
Quoted:
I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. View Quote View All Quotes View All Quotes Quoted:
Quoted:
Cause 3: Over-discharged. Applications without over-discharge preventing device can cause batteries to over-discharge. For example, use low current draw LED light until battery runs out, it cause over-discharge and later cannot charge the battery correctly. Recharging battery 2-3 times solves this problem but if the problem still persists, It is considered battery’ s life span has ended and please stop using. Continuous over-discharging causes damage to the batteries. We recommend to recharge the battery, once luminous energy become low or battery energy become low during using LED light I have been designing and manufacturing Ni-MH & Ni-Cd chemistry battery chargers for 25 yrs. The following are generalized comments. Cells from different manufactures will have different parameters. This is not really true for a single cell but it is true for multiple cells in series. With multiple cells and discharging to zero volts, one of the cells with go to zero first and other(s) will reverse charge that cell as the load current runs thru it. This will damage the zero volt cell. There is no reason to discharge a Ni cell much below 1.0v. At this point something like 95% of stored energy has been used. Anything further is waste of time and risks damaging the cell if used in a series application. that came direct from eneloops data sheet |
|
I have 4 of these 18650 lights. $7.99 a piece, bright as hell, 5 mode, if I lose one meh.
https://www.dealmetic.com/product.asp?ID=FL05518 |
|
|
Most of my cheap 18650 lights get pretty hot.
I usually give my kids some AA or AAA lights that they can play with. Go to lowes and buy a mega pack of their off brand AA or AAA batteries. Those last a LONG time. Plus, I find my rechargable batteries to be too expensive for the kids, as they have a tendency to lose the lights. |
|
$20 well spent; very bright, with battery and charger; 1200 lumens
http://www.amazon.com/gp/product/B00I946KU8/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 or http://www.amazon.com/Fenix-XP-E2-Pocket-Light-Keychain/dp/B00I8D4AMA/ref=sr_1_7?ie=UTF8&qid=1427523779&sr=8-7&keywords=fenix+e12 eta: http://www.midwestblade.com/index.php?option=com_virtuemart&view=productdetails&virtuemart_product_id=140&virtuemart_category_id=154 Got a email this morning: 30% off ALL Fenix Flashlights. Use Coupon Code: 30offFenix Includes all Fenix Flashlights, Batteries, and Chargers! Offers good while supplies last. Offers expires at 11:59pm (CDT) Friday, April 3, 2015. I think this is a good deal (above). I have several, the latest a PD35 at 960 lumens; a little larger than I care to carry in a pocket, but it does fit. I also bought a NiteCore I4 charger that charges a large range of battery types including AA & 18650, CR123A, etc. |
|
different option but this with some rechargeable 123s might be a good option.
https://tigeroutfitters.com/featured/blackhawk-night-ops-legacy-x6-p-flashlight-black.html the Legacy family of lights offers big light output in a compact, rugged package. Perfect for duty carry, personal defense or outdoor excursions, the Legacy X6 is the latest generation of powerful Xenon lamp systems. The penetrating beam signature is perfectly pre-focused, leaving no shadows or artifacts. PRODUCT DETAILS • Anti-roll system for stability • Completely pre-focused, penetrating light beam leaves no shadows or artifacts • Momentary switch or constant on • Max output: 65 lumens • Runtime is 120 minutes with a Xenon bulb Flashlight runs on CR123 batteries. |
|
Quoted:
$20 well spent; very bright, with battery and charger; 1200 lumens http://www.amazon.com/gp/product/B00I946KU8/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 or http://www.amazon.com/Fenix-XP-E2-Pocket-Light-Keychain/dp/B00I8D4AMA/ref=sr_1_7?ie=UTF8&qid=1427523779&sr=8-7&keywords=fenix+e12 eta: http://www.midwestblade.com/index.php?option=com_virtuemart&view=productdetails&virtuemart_product_id=140&virtuemart_category_id=154 Got a email this morning: 30% off ALL Fenix Flashlights. Use Coupon Code: 30offFenix Includes all Fenix Flashlights, Batteries, and Chargers! Offers good while supplies last. Offers expires at 11:59pm (CDT) Friday, April 3, 2015. I think this is a good deal (above). I have several, the latest a PD35 at 960 lumens; a little larger than I care to carry in a pocket, but it does fit. I also bought a NiteCore I4 charger that charges a large range of battery types including AA & 18650, CR123A, etc. View Quote I almost bought the PD40 off midwestblade but they don't sell the battery. |
|
Batman
try http://www.orbtronic.com/26650-batteries-chargers-li-ion-IMR-LiFePO4 or Amazon.com I ordered some 18650s from Amazon and they came from Orbtronic.com |
|
I like these: http://www.amazon.com/gp/product/B00BIYKHVO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
They work great and if I destroy or lose one its not a big deal at that price.. |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.