User Panel
User Panel
User Panel
IL, USA
|
Posted: 3/19/2015 1:33:58 PM EDT
[#1]
Quote HistoryOriginally Posted By LonghunterCO: Where do you get them? Quote HistoryOriginally Posted By LonghunterCO: Originally Posted By bobapunk: Originally Posted By LonghunterCO: Originally Posted By bobapunk: Nice! I just made this over the weekend: https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-xpf1/t31.0-8/11025237_458886130946276_5221562977872693884_o.jpg So snap base on the front side to snap loops onto front of sheath. How are they attached to the back? The screw through the bottom snap is threaded into a post. The post is holding the strap to the sheath. Where do you get them? Anywhere Kydex supplies are sold IFI KK DIY Holsterloops |
|
|
|
Posted: 3/23/2015 4:42:49 PM EDT
[#2]
had my first clip failure. i was on a holster i made for my dad. one of the standard 1.5" IWB clip. he said he was moving the holster on his belt and it broke where the screw holes are. im thinking he was pulling up on it was too much.
|
|
|
|
|
Posted: 3/24/2015 7:46:06 PM EDT
[#3]
Quote HistoryOriginally Posted By evnash: had my first clip failure. i was on a holster i made for my dad. one of the standard 1.5" IWB clip. he said he was moving the holster on his belt and it broke where the screw holes are. im thinking he was pulling up on it was too much. |
|
|
|
|
Posted: 3/24/2015 8:06:14 PM EDT
[#4]
S&W Shield 9mm single mag carrier .080 Kydex R/H IWB Adjustable retention.
I flared the opening for ease of replacing the mag. Small mag.....Small carrier    |
|
|
|
|
Posted: 3/24/2015 8:08:54 PM EDT
[#5]
Quote HistoryOriginally Posted By jjglith:
Some of the early clips were of a inferior material. If your clips did not have the holes pre-drilled it might have been one of them. Also, It helps if you put a small O ring between the clip and Kydex. Quote HistoryOriginally Posted By jjglith:
Originally Posted By evnash:
had my first clip failure. i was on a holster i made for my dad. one of the standard 1.5" IWB clip. he said he was moving the holster on his belt and it broke where the screw holes are. im thinking he was pulling up on it was too much. Metal or silicone o ring? |
|
|
|
|
Posted: 3/24/2015 8:31:22 PM EDT
[#6]
S&W M&P 4.25 9/40 .080 Kydex IWB
Adjustable retention & ride height. Injected molded tuckable strut w/PTD snap. Polymer webbing strap.    |
|
|
|
|
Posted: 3/24/2015 8:37:50 PM EDT
[Last Edit: jjglith]
[#7]
Quote HistoryOriginally Posted By evnash: Metal or silicone o ring? Quote HistoryOriginally Posted By evnash: Originally Posted By jjglith: Originally Posted By evnash: had my first clip failure. i was on a holster i made for my dad. one of the standard 1.5" IWB clip. he said he was moving the holster on his belt and it broke where the screw holes are. im thinking he was pulling up on it was too much. Metal or silicone o ring? http://www.ifithermoplastics.com/products/o-rings |
|
|
|
|
Posted: 3/28/2015 9:04:36 PM EDT
[#8]
Quote HistoryOriginally Posted By PFC_Dustin:
How did you do the stars and hearts? Quote HistoryOriginally Posted By PFC_Dustin:
Originally Posted By 44Punk:
Some of my more recent stuff. I think we are about 500 holsters/sheaths in. <a href="http://s15.photobucket.com/user/johnmontoya44/media/Mobile%20Uploads/image_zpsd587075b.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/Mobile%20Uploads/image_zpsd587075b.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/image_zps3ae93564.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/image_zps3ae93564.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/DFFDC627-18AC-4FD5-A71E-571922D3F85A_zpsmkcvtxk0.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/DFFDC627-18AC-4FD5-A71E-571922D3F85A_zpsmkcvtxk0.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/imagejpg3_zps147072f6.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/imagejpg3_zps147072f6.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/imagejpg1_zps0f76058c.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/imagejpg1_zps0f76058c.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/imagejpg1_zps71fe975a.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/imagejpg1_zps71fe975a.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/55966780-CE49-4678-AC6E-D8828645977C_zpspufrpct4.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/55966780-CE49-4678-AC6E-D8828645977C_zpspufrpct4.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/B8BB62BC-BC40-4C02-9B04-176D151E7EA9_zpsd5es27nq.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/B8BB62BC-BC40-4C02-9B04-176D151E7EA9_zpsd5es27nq.jpg</a> <a href="http://s15.photobucket.com/user/johnmontoya44/media/CDDA0F62-8C83-4537-96BF-08BE7C065E25_zpsvtpmyquv.jpg.html" target="_blank">http://i15.photobucket.com/albums/a397/johnmontoya44/CDDA0F62-8C83-4537-96BF-08BE7C065E25_zpsvtpmyquv.jpg</a> How did you do the stars and hearts? I bought some leather working tools from a guy in Japan. I had to grind them down to get them to fit in my press but they work great. They make ragged holes but you put some heat on afterwords and they clean right up |
|
|
|
LA, USA
|
Posted: 3/28/2015 11:59:40 PM EDT
[#9]
 
|
|
|
MO, USA
|
Posted: 3/29/2015 9:26:11 PM EDT
[#10]
Nowhere near as nice as what some of you guys have made, but my first attempt at a mag pouch.
It is for my 10 round KelTec P32 magazine. The 7 rounder fits & pretty much disappears, but I didn't cut any access out so its really hard to get out. Its a fixable problem, I pretty much just wanted a way to carry the spare mag. Other than this I've only made a few stands for cell phones & tablets so I don't have to hold them when I watch movies. |
|
|
|
Posted: 3/30/2015 12:17:58 PM EDT
[#11]
Quote HistoryOriginally Posted By DAVE_M:
https://farm9.staticflickr.com/8703/16331166923_c0e970fc5a_z.jpghttps://farm8.staticflickr.com/7639/16949926292_a7349f5ba8_z.jpg https://farm8.staticflickr.com/7285/16765026619_17a26d9c50_z.jpg https://farm9.staticflickr.com/8749/16336924423_d4353498bf_z.jpg https://farm9.staticflickr.com/8688/16749634277_93cd3b49ab_z.jpg https://farm8.staticflickr.com/7613/16769553850_cfb3391f48_z.jpg This is SWEET. |
|
|
|
LA, USA
|
Posted: 3/31/2015 7:32:49 AM EDT
[Last Edit: DAVE_M]
[#12]
Quote HistoryOriginally Posted By Dodge223:
This is SWEET. Quote HistoryOriginally Posted By Dodge223:
Originally Posted By DAVE_M:
https://farm9.staticflickr.com/8703/16331166923_c0e970fc5a_z.jpghttps://farm8.staticflickr.com/7639/16949926292_a7349f5ba8_z.jpg https://farm8.staticflickr.com/7285/16765026619_17a26d9c50_z.jpg https://farm9.staticflickr.com/8749/16336924423_d4353498bf_z.jpg https://farm9.staticflickr.com/8688/16749634277_93cd3b49ab_z.jpg https://farm8.staticflickr.com/7613/16769553850_cfb3391f48_z.jpg This is SWEET. Thanks! I carried it without the pouch, Sunday. I may end up changing the loops and adding a larger fire steel, but other than that, I am very pleased with how the sheath came out. Edit - Attached to my belt. I'm sorry you guys have to stare at my cute butt.  
Added a new, larger firesteel and better loops from IFI.  
And here it is mounted to my Condor H20 carrier. 
|
|
|
MO, USA
|
Posted: 4/6/2015 1:42:09 PM EDT
[#13]
He's my new Stalker Shoulder Holster I made last week. Took the inspiration from the old USGI military shoulder / chest holster.
|
|
|
|
Posted: 4/7/2015 6:11:19 PM EDT
[#14]
Quote HistoryOriginally Posted By Chainsaw1:
He's my new Stalker Shoulder Holster I made last week. Took the inspiration from the old USGI military shoulder / chest holster. http://www.arestactical.net/wp-content/uploads/2015/04/stalker-holster.jpg Well done! |
|
|
|
|
Posted: 4/9/2015 5:44:20 AM EDT
[#15]
How is everyone storing all their kydex sheets? I'm having an issue keeping them organized on the shelves I was using.
|
|
|
|
LA, USA
|
Posted: 4/9/2015 9:18:51 AM EDT
[#16]
Quote HistoryOriginally Posted By PFC_Dustin:
How is everyone storing all their kydex sheets? I'm having an issue keeping them organized on the shelves I was using. Still in the box from IFI, color coded, and stacked on top of each other. I have yet to find a reliable way to store 24"x12" sheets, other than this. |
|
|
MO, USA
|
Posted: 4/9/2015 1:08:32 PM EDT
[#17]
wire file folder holder
|
|
|
TX, USA
|
Posted: 4/10/2015 1:28:13 PM EDT
[#18]
Quote HistoryOriginally Posted By Chainsaw1:
wire file folder holder http://ecx.images-amazon.com/images/I/416CdAMP6KL._SY450_.jpg Good call. I found two wire plate drying racks from Ross or TJ Maxx while the wife was shopping. Similar to the folder hanger thing, but flat instead of stepped. I drilled holes in a piece of an old desk and ziptied the wire bases to it for a nice rack. I don't have room on the bench for it now, once I get another table in the shoppe it will be pressed into service. 
|
|
|
|
Posted: 4/10/2015 7:27:30 PM EDT
[#19]
Those are great ideas, thanks. I was using bread crates but they are both too big and too small lol.
|
|
|
|
|
Posted: 4/11/2015 9:36:43 AM EDT
[#20]
Quote HistoryOriginally Posted By PFC_Dustin:
How is everyone storing all their kydex sheets? I'm having an issue keeping them organized on the shelves I was using. I built dividers under my workbench for smallish sheets. The old 4x4 sheets get stored between the back of the bench and the wall. |
|
|
|
|
Posted: 4/16/2015 11:06:23 AM EDT
[#21]
I just finished my Coffee Bum toco press (was using book type press previously). What are you all using to build your blocking to set your spacing for the chicago tension? Would cardboard work or do you have to use hardboard/masonite, or other?
|
|
|
|
LA, USA
|
Posted: 4/16/2015 4:16:52 PM EDT
[Last Edit: DAVE_M]
[#22]
Quote HistoryOriginally Posted By LonghunterCO:
I just finished my Coffee Bum toco press (was using book type press previously). What are you all using to build your blocking to set your spacing for the chicago tension? Would cardboard work or do you have to use hardboard/masonite, or other? Cardboard will compress too much. You are PRESSING the holster after all. Go to Michael's or Hobby Lobby, you can get small pieces of craft pine and beechwood in varying thicknesses for relatively cheap. 
|
|
|
|
Posted: 4/16/2015 6:09:06 PM EDT
[#23]
Thanks Dave_M
. Are you using like a 1/4 stock ? |
|
|
|
IL, USA
|
Posted: 4/17/2015 12:23:23 PM EDT
[#24]
Quote HistoryOriginally Posted By LonghunterCO: Thanks Dave_M . Are you using like a 1/4 stock ? I prefer 3/8" or even 1/2" for thicker guns like the Glock.
Many times the craft board is sold in metric thickness. 13mm is about 1/2" |
|
|
|
Posted: 4/17/2015 12:32:43 PM EDT
[#25]
Has anyone made a Glock 43 holster yet?
|
|
|
|
|
Posted: 4/18/2015 8:02:57 PM EDT
[#26]
Quote HistoryOriginally Posted By seejay3558:
Has anyone made a Glock 43 holster yet? Came here to see this ^^^^ Please IM me if you are. Thanks! |
|
|
|
TX, USA
|
Posted: 4/20/2015 10:29:39 AM EDT
[#27]
whats the favorite "blue gun" of everyone here?? looking for a Glock 17 i can use with and without a light.
|
|
|
LA, USA
|
Posted: 4/20/2015 2:13:16 PM EDT
[Last Edit: DAVE_M]
[#28]
Quote HistoryOriginally Posted By 10Point3:
whats the favorite "blue gun" of everyone here?? looking for a Glock 17 i can use with and without a light. Blue Guns MultiMolds DIYHolster's Drones |
|
|
|
Posted: 4/20/2015 10:54:34 PM EDT
[#29]
Quote HistoryOriginally Posted By DAVE_M:
Blue Guns MultiMolds DIYHolster's Drones Quote HistoryOriginally Posted By DAVE_M:
Originally Posted By 10Point3:
whats the favorite "blue gun" of everyone here?? looking for a Glock 17 i can use with and without a light. Blue Guns MultiMolds DIYHolster's Drones Blue guns I've gotten always were wrong on dimensions so I quit ordering them. Multimolds and diy holsters have always been dead on and never required any tweaking. |
|
|
|
|
Posted: 4/20/2015 11:08:15 PM EDT
[#30]
Does anybody know the best way to mold a M&P Shield with a Lasermax Centerfire.
I don't want to press the laser, but my attempts to block it have failed. I tried hardened molding clay on the prop gun, but blew it apart in the press. I have asked lasermax if I could buy just the shell, but haven't heard back yet. I tried carving one from wood, but can't find it after all that work. That might have actually worked. |
|
|
|
|
Posted: 4/21/2015 10:09:49 PM EDT
[Last Edit: docbrown30]
[#31]
Quote HistoryOriginally Posted By Mach:
Does anybody know the best way to mold a M&P Shield with a Lasermax Centerfire. I don't want to press the laser, but my attempts to block it have failed. I tried hardened molding clay on the prop gun, but blew it apart in the press. I have asked lasermax if I could buy just the shell, but haven't heard back yet. I tried carving one from wood, but can't find it after all that work. That might have actually worked. Just wrap it in a couple layers of painters tape. The Kydex cools quick enough that the heat won't damage it, and the thickness of the gun will prevent the laser from being pressed too tightly. I'd recommend removing the battery, and putting a small block over the button so it isn't activated while holstered. |
|
|
|
|
Posted: 4/21/2015 11:28:24 PM EDT
[#32]
Quote HistoryOriginally Posted By docbrown30:
Just wrap it in a couple layers of painters tape. The Kydex cools quick enough that the heat won't damage it, and the thickness of the gun will prevent the laser from being pressed too tightly. I'd recommend removing the battery, and putting a small block over the button so it isn't activated while holstered. Quote HistoryOriginally Posted By docbrown30:
Originally Posted By Mach:
Does anybody know the best way to mold a M&P Shield with a Lasermax Centerfire. I don't want to press the laser, but my attempts to block it have failed. I tried hardened molding clay on the prop gun, but blew it apart in the press. I have asked lasermax if I could buy just the shell, but haven't heard back yet. I tried carving one from wood, but can't find it after all that work. That might have actually worked. Just wrap it in a couple layers of painters tape. The Kydex cools quick enough that the heat won't damage it, and the thickness of the gun will prevent the laser from being pressed too tightly. I'd recommend removing the battery, and putting a small block over the button so it isn't activated while holstered. I constricted the lower front of an M&P Shield by pressing it. The heat made the Shield's Lower semi-circle of plastic bend in causing friction when the slide moves back. ( the front bottom of the slide that holds the Spring was rubbing against the lower because the lower was reshaped when I pressed it. I was able to fix it with heat and stretching it back out, but I no longer press real guns and that goes for the laser too. |
|
|
|
TX, USA
|
Posted: 4/22/2015 11:30:14 AM EDT
[#33]
Sounds like your heat and/or pressure was too high. Kydex only needs to be 300-315 and pre--heat your foam and mold product to 180-200. I've never had an issue other than magwells becoming tight. Fix that by inserting a full mag or leaving the grip out of the press. The press itself doesn't need to be so tight the carbon deposits turn to diamons, maybe 250-300lbs tight with good foam will give good definition. That's no different than a large American gentleman sitting on the gun in his pickup truck.
|
|
|
IL, USA
|
Posted: 4/22/2015 3:21:07 PM EDT
[#34]
popped my Kryptek cherry last night.
I am pleased:     |
|
|
|
Posted: 4/22/2015 8:17:25 PM EDT
[#35]
Does anyone know where I can find a mold for an M&P Pro 5"? I can't seem to find one anywhere.
|
|
|
|
MO, USA
|
Posted: 4/23/2015 11:14:49 AM EDT
[#36]
No one that I know of has a 5" M&P mold yet. Be careful because the Pro and CORE are different slides IIRC.
|
|
|
|
Posted: 4/23/2015 11:45:57 AM EDT
[#37]
Quote HistoryOriginally Posted By Chainsaw1: No one that I know of has a 5" M&P mold yet. Be careful because the Pro and CORE are different slides IIRC. |
|
|
|
IL, USA
|
Posted: 4/23/2015 5:18:41 PM EDT
[Last Edit: bobapunk]
[#38]
|
|
|
|
Posted: 4/23/2015 7:53:32 PM EDT
[#39]
Quote HistoryI just ordered a G17/22 from Knife kits... Next I'm ordering G34/35.... And mags for those.. I see you have a new list coming out. Are you going to be doing a M&P 22 (and Compact) and mags for them by any chance? Also, I'd like to see CZ Scorpion Mags too... I've only see one person making mag holders for them, I'd like to see if I can make some, when my other parts get here... |
|
|
|
TX, USA
|
Posted: 4/24/2015 11:45:46 AM EDT
[#40]
Quote HistoryOriginally Posted By bobapunk:
popped my Kryptek cherry last night. I am pleased: https://scontent-ord.xx.fbcdn.net/hphotos-xap1/t31.0-8/1973416_496400277194861_2782766625760607652_o.jpg https://scontent-ord.xx.fbcdn.net/hphotos-xpa1/t31.0-8/s960x960/11174577_496400447194844_598015823458006657_o.jpg https://scontent-ord.xx.fbcdn.net/hphotos-xtf1/t31.0-8/11074370_496400313861524_7552849516721107303_o.jpg https://scontent-ord.xx.fbcdn.net/hphotos-xfp1/t31.0-8/s960x960/11048671_496400360528186_3705226961544150381_o.jpg Nice work! That looks almost identical to how I make my holsters. I see in the second pic down at the body bend the separation of the two halves. A huge annoyance of mine. I've found that it comes from finishing your edges and then doing the bend. This method only works if you get the to-be-bent area really hot and pliable and go slooooooow. If you just get it somewhat pliable and force it, it will separate because one piece of kydex is hotter than the other and the cooler one doesnt want to bend with the other at the same rate. I've found that doing just a sisal wheel blend to knock down the sanded edges and a "pre-finish" type edge, then do the body bend, watching out for the separation, pinch that area while hot to seal the edge, then go back to sisal, yellow cloth with black compound, denim wheel, soft cotton wheel. |
|
|
FL, USA
|
Posted: 4/24/2015 12:01:02 PM EDT
[#41]
Quote HistoryOriginally Posted By seejay3558:
Has anyone made a Glock 43 holster yet? Mold will be in today, should have several done this week with pre-orders I have. |
|
|
|
Posted: 4/25/2015 7:09:46 PM EDT
[#42]
Nice work everyone.
Can someone recommend a "kit" that I can try and make an OWB triple magazine holder for G21 mags? Thanks. |
|
|
|
|
Posted: 4/25/2015 10:13:50 PM EDT
[#43]
Probably a dumb question, but will pressing a stippled gun have any adverse affects on the stippling (heat messing it up)?
|
|
|
|
|
Posted: 4/26/2015 12:50:56 AM EDT
[#44]
Quote HistoryOriginally Posted By Lungbuster: Nice work everyone. Can someone recommend a "kit" that I can try and make an OWB triple magazine holder for G21 mags? Thanks. Not sure there is a "Kit"... I would suggest 3 of these http://shop.multimoldguns.com/Multi-Mold-Magazines-MMM.htm .jpg) 2 slices of Kydex 2 Belt clips/loops of your choice... |
|
|
|
|
Posted: 4/26/2015 12:52:17 AM EDT
[#45]
Quote HistoryOriginally Posted By sorzal: Probably a dumb question, but will pressing a stippled gun have any adverse affects on the stippling (heat messing it up)? |
|
|
|
|
Posted: 4/26/2015 1:41:05 AM EDT
[Last Edit: PFC_Dustin]
[#46]
Quote HistoryOriginally Posted By smullen:
I don't think its a dumb question, better safe than sorry... I'd like to know for sure too... Quote HistoryOriginally Posted By smullen:
Originally Posted By sorzal:
Probably a dumb question, but will pressing a stippled gun have any adverse affects on the stippling (heat messing it up)? It didn't have any effect on mine. But taping over it might be good because the stippleing will be molded into the kydex which I would imagine might might act like sand paper on your stipple job as you draw and reholster. I didn't tape mine up but the stipple job was on the part of the holster that I cut off. But no effect on my guns and one of them has been pressed maybe 12 or so times. |
|
|
|
|
Posted: 4/26/2015 9:40:50 AM EDT
[#47]
Quote HistoryOriginally Posted By smullen:
Not sure there is a "Kit"... I would suggest 3 of these http://shop.multimoldguns.com/Multi-Mold-Magazines-MMM.htm http://shop.multimoldguns.com/images/MagBlue(1).jpg 2 slices of Kydex 2 Belt clips/loops of your choice... Quote HistoryOriginally Posted By smullen:
Originally Posted By Lungbuster:
Nice work everyone. Can someone recommend a "kit" that I can try and make an OWB triple magazine holder for G21 mags? Thanks. Not sure there is a "Kit"... I would suggest 3 of these http://shop.multimoldguns.com/Multi-Mold-Magazines-MMM.htm http://shop.multimoldguns.com/images/MagBlue(1).jpg 2 slices of Kydex 2 Belt clips/loops of your choice... Damn. They're as expensive as real magazines. Does the forming process ruin real magazines and that's why these are recommended? |
|
|
|
TX, USA
|
Posted: 4/27/2015 11:27:29 AM EDT
[#48]
Quote HistoryOriginally Posted By Lungbuster:
Damn. They're as expensive as real magazines. Does the forming process ruin real magazines and that's why these are recommended? Quote HistoryOriginally Posted By Lungbuster:
Originally Posted By smullen:
Originally Posted By Lungbuster:
Nice work everyone. Can someone recommend a "kit" that I can try and make an OWB triple magazine holder for G21 mags? Thanks. Not sure there is a "Kit"... I would suggest 3 of these http://shop.multimoldguns.com/Multi-Mold-Magazines-MMM.htm http://shop.multimoldguns.com/images/MagBlue(1).jpg 2 slices of Kydex 2 Belt clips/loops of your choice... Damn. They're as expensive as real magazines. Does the forming process ruin real magazines and that's why these are recommended? If you press a real mag, I would definetly load it with rounds. It needs structure or it will collapse ever so slightly. Snap caps, ehh, unless they are the solid aluminum ones, you'll also need to buy a ton of them, which are about 4x more than real rounds. If anyone doesn't think real rounds are "safe" blah blah, do what you think is safe. I've never had a problem. ANYWAY... You can get double mag drones and singles. If you get two singles, you can tape them with a block and make a double. If you get the double drone, you can only do doubles without significant work to make it a single. The Blue Gun brand mag drones DO NOT have a "bullet" on top as the Multimold brand does. It does make a difference in the final product. I did not know this so I took a dremel and ground away a bit of the "follower" in the blue gun mag and put a dummy round in place. Works perfectly actually. (dummy round is a de-primed piece of brass with a bullet I made on my reloading press.) For rifle mags, I would get the dummy for sure. The pressure would not be good on a Pmag and a USGI aluminum AR mag. Plus they come pre-blocked. |
|
|
|
Posted: 4/27/2015 5:09:52 PM EDT
[#49]
Quote HistoryOriginally Posted By Bizill:
<a href="http://s38.photobucket.com/user/bizill75/media/20150307_120751_zps4fwid3x9.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150307_120751_zps4fwid3x9.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150307_164246_zpslpqbctfx.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150307_164246_zpslpqbctfx.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150307_164141_zpsmcgoniww.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150307_164141_zpsmcgoniww.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150307_164154_zpsrglh8e2i.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150307_164154_zpsrglh8e2i.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150307_170026_zps4pv7qb9a.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150307_170026_zps4pv7qb9a.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150308_194101_zpszkyefnvg.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150308_194101_zpszkyefnvg.jpg</a> <a href="http://s38.photobucket.com/user/bizill75/media/20150308_193100_zpsm6uudrcs.jpg.html" target="_blank">http://i38.photobucket.com/albums/e139/bizill75/20150308_193100_zpsm6uudrcs.jpg</a> Tried to IM you but the inox is full. Hit me up. |
|
|
|
|
Posted: 4/27/2015 5:57:45 PM EDT
[#50]
A lot of people have just used wood sized and shaped to the mags. For P mags I just use bad mags filled with foam sealant.
|
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
