User Panel
Posted: 5/15/2024 4:02:15 PM EDT
What options are there if your barrel/bolt have too small of a headspace and you have failure to extract issues?
Try to ream it out? Use some sandpaper to wear down the throat? |
|
|
Speaking of AR type rifle I would not expect failure to extract from inadequate headspace. Instead, I would expect the bolt to not fully close and the firing pin does not reach the primer causing failure to fire problems and along with that hard to hand extract unfired chambered or partially chambered rounds. But that is just me.
|
|
|
Are you certain the ammo isn't the issue? Try a couple different bolts before you attempt to ream the chamber. If it's a chrome or nitrided barrel, I would find another barrel and bolt combination that gives an acceptable headspace dimension. EDIT: what does a go, no-go and field gauge show? You're saying this combination of bolt and barrel will not lock on a "Go" dimension gauge?
|
|
"Peace is that brief glorious moment in history when everybody stands around reloading." -Thomas Jefferson
RIP TSgt Jason Norton and SSgt Brian McElroy. KIA 22 Jan 06, near Taji, Iraq. LaRue Armorer Glock Armorer NRA Life Member |
Originally Posted By CATM: Are you certain the ammo isn't the issue? Try a couple different bolts before you attempt to ream the chamber. If it's a chrome or nitrided barrel, I would find another barrel and bolt combination that gives an acceptable headspace dimension. EDIT: what does a go, no-go and field gauge show? You're saying this combination of bolt and barrel will not lock on a "Go" dimension gauge? View Quote No go is good. I cheaped out and didn't get the go, I'm seeing that was a mistake. I just used a loaded round thinking "good enough". I'll try some different ammo and see if that helps. And ya it's a nitride barrel. I do have a spare bolt I'll try also that I forgot I had. |
|
|
If it's closing on ammo and you are firing it, then it has enough headspace. Now it may have tight headspace, but that's another issue. What makes you think you extraction issue has to do with headspace?
Also more details would be helpful. |
|
|
Originally Posted By bpm990d: If it's closing on ammo and you are firing it, then it has enough headspace. Now it may have tight headspace, but that's another issue. What makes you think you extraction issue has to do with headspace? Also more details would be helpful. View Quote This ^^^ Been preaching it for years. Also, in agreement that we need more info. |
|
|
Originally Posted By j3_: Speaking of AR type rifle I would not expect failure to extract from inadequate headspace. Instead, I would expect the bolt to not fully close and the firing pin does not reach the primer causing failure to fire problems and along with that hard to hand extract unfired chambered or partially rounds. But that is just me. View Quote The AR, like many military weapons, uses a concept called "crush-up" - the longest allowable case is somewhat longer than the shortest allowable chamber. I don't remember exactly what this figure is, but I want to say it's like .003". I'll have to check my notes when I get home. Steel cases might present a problem in this regard. |
|
|
Originally Posted By CPT_CAVEMAN: What options are there if your barrel/bolt have too small of a headspace and you have failure to extract issues? Try to ream it out? Use some sandpaper to wear down the throat? View Quote What kind of ammo are you shooting? |
|
|
Originally Posted By brownbomber: The AR, like many military weapons, uses a concept called "crush-up" - the longest allowable case is somewhat longer than the shortest allowable chamber. I don't remember exactly what this figure is, but I want to say it's like .003". I'll have to check my notes when I get home. Steel cases might present a problem in this regard. View Quote SAAMI specifications for the maximum cartridge case give the headspace as 1.4666". SAAMI specifications for the minimum chamber give the headspace as 1.4636". That gives a maximum crush up of 0.0030". SAAMI allows a crush as well. Military maximum case length is 1.4667" M16 minimum chamber is 1.4646", 0.0021" crush. M249 minimum chamber is 1.4611". 0.0056" crush. |
|
|
Originally Posted By brownbomber: The AR, like many military weapons, uses a concept called "crush-up" - the longest allowable case is somewhat longer than the shortest allowable chamber. I don't remember exactly what this figure is, but I want to say it's like .003". I'll have to check my notes when I get home. Steel cases might present a problem in this regard. View Quote I have never ran into commercial ammo that I have purchased that the case was sized to cause a crush even if drawings, Saami, or govt. specs allowed it. I based my response on my own experiences only which has worked very well for me. If there is fault in it based on equal real world experiences that are different than mine I would consider those for my own use based on their value. Post up a manufacturer making cases or ammunition sized to utilize any allowed crush for an AR!5 if someone knows of one. At most wouldn't that crush scenario only apply to trying to extract an unfired round? |
|
|
Originally Posted By j3_: I have never ran into commercial ammo that I have purchased that the case was sized to cause a crush even if drawings, Saami, or govt. specs allowed it. I based my response on my own experiences only which has worked very well for me. If there is fault in it based on equal real world experiences that are different than mine I would consider those for my own use based on their value. Post up a manufacturer making cases or ammunition sized to utilize any allowed crush for an AR!5 if someone knows of one. At most wouldn't that crush scenario only apply to trying to extract an unfired round? View Quote I'm fairly certain that no man'f are incorporating "crush" into their ammo specs. Folks are shooting that stuff in firearms other than AR's. Headspace will have little to no effect on extraction/ejection, IMO. Once it goes bang, everything changes. |
|
|
Originally Posted By lysanderxiii: SAAMI specifications for the maximum cartridge case give the headspace as 1.4666". SAAMI specifications for the minimum chamber give the headspace as 1.4636". That gives a maximum crush up of 0.0030". SAAMI allows a crush as well. Military maximum case length is 1.4667" M16 minimum chamber is 1.4646", 0.0021" crush. M249 minimum chamber is 1.4611". 0.0056" crush. View Quote View All Quotes View All Quotes Originally Posted By lysanderxiii: Originally Posted By brownbomber: The AR, like many military weapons, uses a concept called "crush-up" - the longest allowable case is somewhat longer than the shortest allowable chamber. I don't remember exactly what this figure is, but I want to say it's like .003". I'll have to check my notes when I get home. Steel cases might present a problem in this regard. SAAMI specifications for the maximum cartridge case give the headspace as 1.4666". SAAMI specifications for the minimum chamber give the headspace as 1.4636". That gives a maximum crush up of 0.0030". SAAMI allows a crush as well. Military maximum case length is 1.4667" M16 minimum chamber is 1.4646", 0.0021" crush. M249 minimum chamber is 1.4611". 0.0056" crush. M240 is -.009 crush to +.007 clearance. M60 is -.0025 crush to +.0065 clearance. The 1918 BAR is -.0092 crush to +.0087 clearance. The M14 and M14 National Match both DONT have any crush. The M1 Garand is -.0056 crush to +.0044 clearance. |
|
|
Originally Posted By j3_: I have never ran into commercial ammo that I have purchased that the case was sized to cause a crush even if drawings, Saami, or govt. specs allowed it. I based my response on my own experiences only which has worked very well for me. If there is fault in it based on equal real world experiences that are different than mine I would consider those for my own use based on their value. Post up a manufacturer making cases or ammunition sized to utilize any allowed crush for an AR!5 if someone knows of one. At most wouldn't that crush scenario only apply to trying to extract an unfired round? View Quote View All Quotes View All Quotes Originally Posted By j3_: Originally Posted By brownbomber: The AR, like many military weapons, uses a concept called "crush-up" - the longest allowable case is somewhat longer than the shortest allowable chamber. I don't remember exactly what this figure is, but I want to say it's like .003". I'll have to check my notes when I get home. Steel cases might present a problem in this regard. I have never ran into commercial ammo that I have purchased that the case was sized to cause a crush even if drawings, Saami, or govt. specs allowed it. I based my response on my own experiences only which has worked very well for me. If there is fault in it based on equal real world experiences that are different than mine I would consider those for my own use based on their value. Post up a manufacturer making cases or ammunition sized to utilize any allowed crush for an AR!5 if someone knows of one. At most wouldn't that crush scenario only apply to trying to extract an unfired round? If you have an AR15 minimum chamber and an 5.56mm maxiumum-length case, you have a very slight crush condition. I'm not sure if you'd even be able to feel that, because I've never done it before. I suspect that cartridge length and chamber length follow a normal-distributuon, with very few falling at the extremes (but I don't know that for a fact). Crush-up is discussed in this publication: Technical Notes Small Arms Design, by John Rocha |
|
|
Is this a new barrel? What type of bore does it have, chrome lined or no? I had extraction issues with a DPMS barrel years ago. Stick with chrome lined or nitrided barrels.
|
|
|
Originally Posted By brownbomber: What kind of ammo are you shooting? View Quote View All Quotes View All Quotes Originally Posted By brownbomber: Originally Posted By CPT_CAVEMAN: What options are there if your barrel/bolt have too small of a headspace and you have failure to extract issues? Try to ream it out? Use some sandpaper to wear down the throat? What kind of ammo are you shooting? "Sergeant Major" |
|
|
Originally Posted By AZ_Gun_Nut: Is this a new barrel? What type of bore does it have, chrome lined or no? I had extraction issues with a DPMS barrel years ago. Stick with chrome lined or nitrided barrels. View Quote Brand new barrel, nitride. Thought it might be a tight chamber so used some flitz and a drill to "hone" it or remove a little material. Thought it might be a pressure curve issue, but that doesn't make complete sense. So super tight headspace I'm pretty sure is the issue and looking for the cheapest and/or quickest option to fix it. |
|
|
Originally Posted By CPT_CAVEMAN: "Sergeant Major" View Quote View All Quotes View All Quotes Originally Posted By CPT_CAVEMAN: Originally Posted By brownbomber: Originally Posted By CPT_CAVEMAN: What options are there if your barrel/bolt have too small of a headspace and you have failure to extract issues? Try to ream it out? Use some sandpaper to wear down the throat? What kind of ammo are you shooting? "Sergeant Major" Cold-worked steel cartridge cases do not have the elastic recovery that brass cases have. Large portions of the case are actually larger than the chamber after they are fired, not unlike a press-fit dowel pin. They must be yanked out with tremendous force, which sometimes exceeds the strength of the rim. The 7.62x39 case has much more taper and a much thicker rim for this reason. This phenomenon is discussed in many, many publications, including the Oerlikon Pocketbook. I don't think the extraction failures in your weapon are any indication of a headspace problem. |
|
|
|
|
|
Originally Posted By s4s4u: So you are wanting to change the chamber dimensions of a rifle because one type of ammo is giving you problems, without ever trying any other ammo? I think that may be a bit....rash....no? View Quote Well, when you put it that way lol. But it has worked in every other gun I've shot it in. |
|
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.