User Panel
Posted: 5/29/2023 10:42:57 AM EDT
Looking for a good punch set that wont scratch my weapons, any suggestions?
|
|
|
I'm not sure I understand. Any punch - used improperly - will scratch what you're working on.
Are you wanting polymer punches? Brass? Steel? |
|
|
In my opinion these gedore punches and drifts are the best, now as far as avoiding scratching your firearm this is 100% on the craftsmen
https://www.kctool.com/gedore-113-drift-punch-set-6-pcs-in-plastic-holder/ https://www.kctool.com/gedore-116-l-pin-punch-set-6-pcs-in-plastic-holder/ |
|
|
I'm sorry I'm new to armory and DIY but I have basic knowledge in guns. What's the difference between brass and steel punches?
I have some roll pins I need to remove to work on a upper. Just need the proper tools. |
|
|
If you’re just banging in roll pins then this tekton set is good enough. Been using mine for a few years now and haven’t had any problems.
https://www.amazon.com/dp/B012TKY0VI?tag=arfcom00-20 |
|
|
When I went looking for a set of Delrin or similar punches, I was surprised that there basically weren’t any.
I purchased some Delrin dowels from Amazon. Way longer than necessary, I cut them down into useable sizes. |
|
If the truth makes you uncomfortable, don't blame the truth. Blame the lie that made you comfortable. -James Ng Uni
|
Pay the $16 or so for the special bolt catch punches.
|
|
To compel a man to subsidize with his taxes the propagation of ideas which he disbelieves and abhors is sinful and tyrannical.
Thomas Jefferson, 3rd President of US (1743 - 1826) LGBTQ - Let's Get Biden To Quit |
Originally Posted By Jerrylo913: I'm sorry I'm new to armory and DIY but I have basic knowledge in guns. What's the difference between brass and steel punches? I have some roll pins I need to remove to work on a upper. Just need the proper tools. View Quote I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. |
|
#Pureblood
|
Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. View Quote Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. |
|
#53 says, "Take 22 mg absorbed Vit C per lb plus 1 gram Chaga daily. Don't forget 2000iu Vit D-3 & K-2, 30 mg Zinc and 2 mg Cu."
Unfettered with the formalities of an economics education but well read in monetary history. |
Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. View Quote Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. |
|
#53 says, "Take 22 mg absorbed Vit C per lb plus 1 gram Chaga daily. Don't forget 2000iu Vit D-3 & K-2, 30 mg Zinc and 2 mg Cu."
Unfettered with the formalities of an economics education but well read in monetary history. |
Get some blue painters tape
If really nit picky use 3-4 layers Wheelers has a complete AR tool set Not necessarily the best but good Birchwood Casey has some Aluma -black To touch up spots, read directions fully |
|
|
Originally Posted By Jerrylo913: I'm sorry I'm new to armory and DIY but I have basic knowledge in guns. What's the difference between brass and steel punches? I have some roll pins I need to remove to work on a upper. Just need the proper tools. View Quote https://www.brownells.com/tools-cleaning/general-gunsmith-tools/punches/roll-pin-punches/ |
|
|
It's not clear to me what you're doing, but if it's roll pins, then roll pin starter punches make life much easier.
|
|
|
Originally Posted By Riter: Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. View Quote View All Quotes View All Quotes Originally Posted By Riter: Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. Good to know, thanks! |
|
#Pureblood
|
Originally Posted By Sketti: Good to know, thanks! View Quote View All Quotes View All Quotes Originally Posted By Sketti: Originally Posted By Riter: Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. Good to know, thanks! WD40 and 0000 steel wool as well. |
|
Can't never could 'til try came along.
|
Originally Posted By TGWLDR: WD40 and 0000 steel wool as well. View Quote View All Quotes View All Quotes Originally Posted By TGWLDR: Originally Posted By Sketti: Originally Posted By Riter: Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. Good to know, thanks! WD40 and 0000 steel wool as well. |
|
#Pureblood
|
Originally Posted By Sketti: 0000 steel wool won't leave small scratchs? View Quote View All Quotes View All Quotes Originally Posted By Sketti: Originally Posted By TGWLDR: Originally Posted By Sketti: Originally Posted By Riter: Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. Good to know, thanks! WD40 and 0000 steel wool as well. Correct. |
|
Can't never could 'til try came along.
|
Originally Posted By TGWLDR: Originally Posted By Sketti: Originally Posted By TGWLDR: Originally Posted By Sketti: Originally Posted By Riter: Originally Posted By Sketti: Brass is a softer metal and less likely to scratch however it's not as strong as the steel punch and may bend easier. Keep in mind you can still scratch your upper with a brass punch if you hit the punch wrong, etc. I'm new to DIYing myself and have been testing various different things/brand names. So far I like the Mayhew, Starrett, and Grace brand punches, all are made in the USA. Also, having a good/appropriate hammer is just as important as having good punches. Brass marks may be removed with Hoppes or gun solvent. I'd use brass too. Good to know, thanks! WD40 and 0000 steel wool as well. Correct. cool, thanks! |
|
#Pureblood
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.