User Panel
Posted: 12/5/2016 2:55:44 AM EDT
I need to install a 5.56 barrel into an upper. I can't find a reason to spend the money on a reaction rod, as it only does one caliber. I plan on a 9mm, an A1, and a dedicated .22, and a reaction rod wouldn't make sense spending all that money if I'm only going to make a couple 556 guns. I read that the clam shells weren't advised because it can warp the receiver while torquing the barrel down. My second idea was to use the magpul vice because it has more than one purpose. How would I torque a 9mm or .22 gun? Would a clamshell work for these?
|
|
if you have a decent bench vise make a set of barrel blocks out of oak.
|
|
Quoted:
I read that the clam shells weren't advised because it can warp the receiver while torquing the barrel down. View Quote The only way a clamshell goes wrong, is if you use one that was designed to fit a specific manufacturer's billet receiver, and try using it on a different one that it doesn't fit. The reason for this is that there is no "standard" outside dimensions for billet. Forged receivers should all be the same, though. |
|
|
AFAIK people have managed to damage uppers using any of the installation tools.
I have used clamshells since they came onto the market and have not had any problems. |
|
Reaction Rods cause more problems than clamshell upper receiver vise blocks.
|
|
I have only done one build so I am not exactly a plethora of data, but I used the Brownells clam shell, torqued to 60 and had zero issues. The gun runs beautifully.
|
|
What I use:
Wheeler Engineering Clamshell & BCG/Gas Tube Alignment Tool Brownell's Armorer's Wrench or Proprietary Barrel Nut Wrench AeroShell 64 (33MS) Magnetic Nylon Soft Jaws & Strip of Leather for Flash Hider Installation |
|
They won't work for A1/A2 uppers but any flat tops I would recommend this. Used in the horizontal position you can safely install barrels etc. I've now done several builds with them and have been very pleased.
|
|
Quoted:
Where did you read that? Sales propaganda for some other product? Hundreds of thousands of rifles have been assembled for decades using clamshells. Every shop that I know of uses them daily. I don't know of one professional shop assembling ARs that uses a reaction rod, or any other barrel extension holding tool. The only way a clamshell goes wrong, is if you use one that was designed to fit a specific manufacturer's billet receiver, and try using it on a different one that it doesn't fit. The reason for this is that there is no "standard" outside dimensions for billet. Forged receivers should all be the same, though. View Quote After actually assembling several thousand uppers over the last several years using RR's without a single mishap, perhaps you would enlighten me as to what I am doing wrong. Enquiring minds want to know. Not trying to bust your chops there bbies1973, but my real world experience contradicts your, I assume, opinion. If not an opinion, please point me in the direction of the evidence your statement is based on. I honestly do not see how you can come to your conclusion based on any real life experience. I do not in any way claim to have all the answers, AND AM ALWAYS WILLING TO LEARN from others, and their experiences. So help a brother out and learn me something. |
|
Quoted:
They won't work for A1/A2 uppers but any flat tops I would recommend this. Used in the horizontal position you can safely install barrels etc. I've now done several builds with them and have been very pleased. View Quote You are correct outrider, in that the product you mentioned is designed to allow the barrel/nut install. It will not protect against the possibility of stripping out the alignment pin when installing a muzzle device. While a rare event I have seen it happen when the barrel extension is un-supported. If one is only doing a few builds, then imho a good set of barrel blocks is more than adequate when properly fitted and used. |
|
Quoted:
Where did you read that? Sales propaganda for some other product? Hundreds of thousands of rifles have been assembled for decades using clamshells. Every shop that I know of uses them daily. I don't know of one professional shop assembling ARs that uses a reaction rod, or any other barrel extension holding tool. The only way a clamshell goes wrong, is if you use one that was designed to fit a specific manufacturer's billet receiver, and try using it on a different one that it doesn't fit. The reason for this is that there is no "standard" outside dimensions for billet. Forged receivers should all be the same, though. View Quote https://www.youtube.com/watch?v=s_vFcUc_tbo Daniel Defense uses reaction rods. |
|
Quoted:
https://www.youtube.com/watch?v=s_vFcUc_tbo Daniel Defense uses reaction rods. View Quote Thanks for linking that video. I'm a little disappointed with a few of the assembly procedures shown in that video. No lube was used for the barrel nut or the castle nut, there was no proper support used to hold the lower receiver for installing and staking the castle nut and they used a Reaction Rod to install the barrel nut and the flash suppressor. With the reputation that Daniel Defense has I expected better. I'll add them to my list of companies that use Reaction Rods I guess. BCM Sig Sionics Knight's Armament HK Daniel Defense |
|
Quoted:
if you have a decent bench vise make a set of barrel blocks out of oak. View Quote This has been my method for years. It's not the most high tech solution but it works for me. As someone else said you can damage the receiver even with the right tools if you over torque or apply too much pressure anyway. |
|
Assuming you have a large bench vice?
I have a colt armorer's manual dated 1992, it shows aluminum barrel blocks only! I bought a set from model 1 sales in '04 and have been using them ever since. It is all colt recommends. You can do muzzle devises with it also, where as any of the other upper blocks or rods will leave a 16 or 20" unsupported barrel, not good for cranking on the muzzle end. |
|
I just use the Wheeer's clamshell with the gas tube alignment deal.
I am 2 for 2 of not screwing anything up. Going to use it for the third one too. |
|
Wheelers clamshell $50 and I made a ghetto barrel block with a hand saw, a drill bit and a 2x4. My vise is only 3.5" and bolted to my workbench.
If you don't have a workbench, bolt your vise to a 2x4 and park your car on it. It doesn't take much $. |
|
I've had good luck with clamshells and the Magpul BEV block. i bought the bev block because two of my builds were billets that wouldn't fit in a clamshell.
One thing I like about the bev block is that it locks into the barrel extension and keeps the barrel from shifting when being tightened. |
|
I use these http://www.spikestactical.com/tools-block-worx-upper-vise-block-p-557.html
|
|
Quoted:
They won't work for A1/A2 uppers but any flat tops I would recommend this. Used in the horizontal position you can safely install barrels etc. I've now done several builds with them and have been very pleased. View Quote |
|
|
Vise blocks, reaction rod, etc.
Matters very little ocmpared to using a half decent torque wrench. Cheap ones suck. The cheapo loaners at ORileys and AutoZone suck. The cheapos at HD most likely suck. Basically, the Chinese don't make any good ones. |
|
Quoted:
Oh please elaborate! I have both, and used both, I'll take the RR for barrel and muzzle device install all day long. I've seen sheared barrel extension index pins from clamshells View Quote Just do a search. You will see plenty of threads about sheared indexing pins, and loosened barrel extensions caused by Reaction Rod use. The rare occurrence of a sheared indexing pin while using clamshell upper receiver vise blocks is usually caused by someone using them incorrectly trying to remove or install a muzzle devise. Clamshell upper receiver vise blocks are the wrong tool for muzzle devise work. Clamshell upper receiver vise blocks are for barrel installation/removal only. Barrel blocks are for muzzle devise work only. Geissele Super Reaction Rod can work for barrel installation or removal but they are to complicated and a pain to set up. Reaction Rod style tools can be used for muzzle devise work but you are at risk of loosening or tightening the barrel extension if it was not torqued to spec. |
|
Agree with post above. Use clamshell for barrel installation. For muzzle devices, I wrap a strip of leather around the barrel and clamp it really hard as close to the device as possible in a strong bench vise. Leather grips the barrel well.
|
|
Quoted:
Vise blocks, reaction rod, etc. Matters very little ocmpared to using a half decent torque wrench. Cheap ones suck. The cheapo loaners at ORileys and AutoZone suck. The cheapos at HD most likely suck. Basically, the Chinese don't make any good ones. View Quote Lol I have the harbor freight torque wrench on sale for 10 dollars... |
|
Quoted:
Oh please elaborate! I have both, and used both, I'll take the RR for barrel and muzzle device install all day long. I've seen sheared barrel extension index pins from clamshells View Quote View All Quotes View All Quotes Quoted:
Quoted:
Reaction Rods cause more problems than clamshell upper receiver vise blocks. Oh please elaborate! I have both, and used both, I'll take the RR for barrel and muzzle device install all day long. I've seen sheared barrel extension index pins from clamshells More than one barrel manufacturer had come in and said that supporting the barrel extension when attaching the barrel nut is bad, because the extension is torqued into the barrel.and it can be shifted and come out of head space. There are only two things that need attention when attaching a barrel: the threads on the receiver need to be held steady, and a wrench needs to tighten the barrel nut. There is no reason at all to have pressure on a third area, the barrel extension, which has nothing to do with how tightly the barrel nut is torqued down. It's also a bad idea to use a RR to put on muzzle devices because it can ruin the head space. I like the No-Mar blocks. You want a barrel block for the muzzle device. Nothing else is necessary, and is possibly harmful. |
|
Quoted:
Lol I have the harbor freight torque wrench on sale for 10 dollars... View Quote View All Quotes View All Quotes Quoted:
Quoted:
Vise blocks, reaction rod, etc. Matters very little ocmpared to using a half decent torque wrench. Cheap ones suck. The cheapo loaners at ORileys and AutoZone suck. The cheapos at HD most likely suck. Basically, the Chinese don't make any good ones. Lol I have the harbor freight torque wrench on sale for 10 dollars... I use the mk1 arm, usually. 30 to 80lbs a foot from the pivot point is spec. |
|
Quoted:
More than one barrel manufacturer had come in and said that supporting the barrel extension when attaching the barrel nut is bad, because the extension is torqued into the barrel.and it can be shifted and come out of head space. View Quote I agree with the majority of your post but you cannot affect the head space by installing or removing a barrel nut with the reaction rod, though you can potentially affect head space by installing or removing a muzzle devise. I think it may have been Ballistic Advantage or Faxon Firearms that were warning against Reaction Rod use for muzzle devise installation or removal for the reason that it could affect head space. Both ADCO and Ken Elmore from Specialized Armament have advised against using the Reaction Rod for installing or removing barrel nuts. |
|
|
Quoted:
They won't work for A1/A2 uppers but any flat tops I would recommend this. Used in the horizontal position you can safely install barrels etc. I've now done several builds with them and have been very pleased. View Quote I had always used a clamshell vice block until I discovered the Plastix Revolution blocks in the link above. It works great and is one of the cheapest options available. I highly reccomend it. |
|
Quoted:
Thanks for linking that video. I'm a little disappointed with a few of the assembly procedures shown in that video. No lube was used for the barrel nut or the castle nut, there was no proper support used to hold the lower receiver for installing and staking the castle nut and they used a Reaction Rod to install the barrel nut and the flash suppressor. With the reputation that Daniel Defense has I expected better. I'll add them to my list of companies that use Reaction Rods I guess. BCM Sig Sionics Knight's Armament HK Daniel Defense View Quote You can tell all of that from the video? It was a time lapse video, I wouldn't form any kind of opinion based off of that. One thing you can tell though is that they did not use the torque wrench at 90 degrees to the barrel nut wrench, which has been an argument I've seen around here several times. I personally don't think that matters but I thought I'd point it out. |
|
Quoted:
You can tell all of that from the video? It was a time lapse video, I wouldn't form any kind of opinion based off of that. One thing you can tell though is that they did not use the torque wrench at 90 degrees to the barrel nut wrench, which has been an argument I've seen around here several times. I personally don't think that matters but I thought I'd point it out. View Quote Maybe you're right and I shouldn't judge if they greased the threads or not based on what could be seen in the video. I guess they could have pre-greased both the barrel nut and the castle nut. They certainly do use a Reaction Rod though and no proper support for installing and staking the castle nut. |
|
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.