User Panel
Posted: 9/9/2010 5:59:47 PM EDT
Is it possible to put a turbo charger on a 85 GMC with a V8 Gas under the hood? Sorry for the newbish question.
Thanks Scott |
|
Sure, it is possible.
How well it would function and how much you'd draw out of that motor in its stock form is a different question though. |
|
Quoted:
Sure, it is possible. How well it would function and how much you'd draw out of that motor in its stock form is a different question though. Whats your thoughts on that? Or would I be better off finding a Cummins or a Duramax for it? Scott |
|
Quoted:
Quoted:
Sure, it is possible. How well it would function and how much you'd draw out of that motor in its stock form is a different question though. Whats your thoughts on that? Or would I be better off finding a Cummins or a Duramax for it? Scott There's probably some guys that can help you out a lot better than I can on here, regarding force induction from scratch on a stock V8 motor. That being said, I'm not sure of the compression you have and the setup you'd be looking at. What are you looking to get out of this motor by turbocharging it? Are you looking at performance, power, etc. from a "per dollar" aspect? |
|
Power is what i'm lacking and needing, performance would be nice to, I feel it needs a lil more giddy up when I'm pulling trailers and in general. I probably dont need it still being in highschool, but its cheaper than a rebuilt Duramax or Cummins. And i dont understand your "per dollar" aspect. Im guessing your saying buying power with add ons.
|
|
Quoted:
Power is what i'm lacking and needing, performance would be nice to, I feel it needs a lil more giddy up when I'm pulling trailers and in general. I probably dont need it still being in highschool, but its cheaper than a rebuilt Duramax or Cummins. And i dont understand your "per dollar" aspect. Im guessing your saying buying power with add ons. By "per dollar", I mean are you trying to get the most power for you buck...or are you just trying to get the most power regardless of cost? I'm trying to help you sort out what would be the most cost effective, short-term and long-term, for you and your truck –– if that's what you're looking for as well. |
|
Quoted:
Quoted:
Power is what i'm lacking and needing, performance would be nice to, I feel it needs a lil more giddy up when I'm pulling trailers and in general. I probably dont need it still being in highschool, but its cheaper than a rebuilt Duramax or Cummins. And i dont understand your "per dollar" aspect. Im guessing your saying buying power with add ons. By "per dollar", I mean are you trying to get the most power for you buck...or are you just trying to get the most power regardless of cost? I'm trying to help you sort out what would be the most cost effective, short-term and long-term, for you and your truck –– if that's what you're looking for as well. My apologies. long day, and most power for my buck would be nice. If i gotta drop some cash i will, but if i can do it for a lower cost that will work just as good i will. |
|
Not cost effective. At the minimum, you need:
- turbo(s) - header/exhaust fabrication - drill and tap the block for turbo oil feed and return lines - replace stock cast pistons with forged pistons (if you want to run more than 5psi without cracking pistons) - high flow/pressure fuel pump - larger fuel injectors - computer that can accept a custom tune - access to a dyno to tune the computer A better option would be to buy a crate engine or build up a motor to your liking. |
|
Quoted:
Not cost effective. At the minimum, you need: - turbo(s) - header/exhaust fabrication - drill and tap the block for turbo oil feed and return lines - replace stock cast pistons with forged pistons (if you want to run more than 5psi without cracking pistons) - high flow/pressure fuel pump - larger fuel injectors - computer that can accept a custom tune - access to a dyno to tune the computer A better option would be to buy a crate engine or build up a motor to your liking. *whistles* So your saying get a rebuilt Duramax or Cummins that has a turbo and drop it in? Scott |
|
Quoted:
Quoted:
Not cost effective. At the minimum, you need: - turbo(s) - header/exhaust fabrication - drill and tap the block for turbo oil feed and return lines - replace stock cast pistons with forged pistons (if you want to run more than 5psi without cracking pistons) - high flow/pressure fuel pump - larger fuel injectors - computer that can accept a custom tune - access to a dyno to tune the computer A better option would be to buy a crate engine or build up a motor to your liking. *whistles* So your saying get a rebuilt Duramax or Cummins that has a turbo and drop it in? Scott Gasser. You don't want to try a diesel swap unless you have a complete donor truck of the same model/vintage. |
|
If you want to tow big, id get a 3/4 ton to 1 ton truck.
Ford F250+ Dodge Ram 2500+ etc etc. |
|
I don't mean to be rude when I say that if you don't know that turbocharger is one word, this project won't end well.
If someone makes a kit to drop in a diesel motor of any kind you will be better off than with a turbo gas motor IMO. The fuel injection setup alone will be a large expense unless you are very skilled at tuning. To be honest, you can probably buy a turbo diesel truck for less than what this project will cost you. A friend of mine just picked up a F450 diesel with a 12' dump on it for $3,750. The hydraulics on the bed need gone through, but the motor has 140K on the 7.3 turbo diesel motor in it. It has a 5 speed and pulls whatever he needs. It came with a huge file of receipts and was thoroughly checked out by a good diesel repair shop. The guy told him that he will never get a better deal on a vehicle. ETA: The other guys are right that if you just drop a diesel into a half ton truck the truck won't be able to handle it. |
|
Quoted:
I don't mean to be rude when I say that if you don't know that turbocharger is one word, this project won't end well. If someone makes a kit to drop in a diesel motor of any kind you will be better off than with a turbo gas motor IMO. The fuel injection setup alone will be a large expense unless you are very skilled at tuning. To be honest, you can probably buy a turbo diesel truck for less than what this project will cost you. A friend of mine just picked up a F450 diesel with a 12' dump on it for $3,750. The hydraulics on the bed need gone through, but the motor has 140K on the 7.3 turbo diesel motor in it. It has a 5 speed and pulls whatever he needs. It came with a huge file of receipts and was thoroughly checked out by a good diesel repair shop. The guy told him that he will never get a better deal on a vehicle. ETA: The other guys are right that if you just drop a diesel into a half ton truck the truck won't be able to handle it. Good point there, it wouldnt have ended well. O hell. Everyone done poked holes in my ideas, which is a good thing, since they know more than me. Now i will be looking for a new truck. Scott |
|
Quoted:
Quoted:
Quoted:
Not cost effective. At the minimum, you need: - turbo(s) - header/exhaust fabrication - drill and tap the block for turbo oil feed and return lines - replace stock cast pistons with forged pistons (if you want to run more than 5psi without cracking pistons) - high flow/pressure fuel pump - larger fuel injectors - computer that can accept a custom tune - access to a dyno to tune the computer A better option would be to buy a crate engine or build up a motor to your liking. *whistles* So your saying get a rebuilt Duramax or Cummins that has a turbo and drop it in? Scott Gasser. You don't want to try a diesel swap unless you have a complete donor truck of the same model/vintage. Little explanation would be nice here. Thanks Scott |
|
i didnt see anything posted about what you are towing. how heavy & how far?
what kind of 85 GMC ? on top of what is posted above, you may need to upgrade your transmission too. buying a used diesel truck would probably be a better bang for the buck, but that all depends on your intended use. as well as what you need versus want in towing |
|
Before spending money engine performance/swap stuff have you checked your ring/pinion gear vs tire diameter to see if a r&p change might be what you need?
Brian |
|
Quoted:
Quoted:
Quoted:
Quoted:
Not cost effective. At the minimum, you need: - turbo(s) - header/exhaust fabrication - drill and tap the block for turbo oil feed and return lines - replace stock cast pistons with forged pistons (if you want to run more than 5psi without cracking pistons) - high flow/pressure fuel pump - larger fuel injectors - computer that can accept a custom tune - access to a dyno to tune the computer A better option would be to buy a crate engine or build up a motor to your liking. *whistles* So your saying get a rebuilt Duramax or Cummins that has a turbo and drop it in? Scott Gasser. You don't want to try a diesel swap unless you have a complete donor truck of the same model/vintage. Little explanation would be nice here. Thanks Scott Lots of parts are different beyond the motor. You need the diesel's fuel tank, transfer pump, water separator, etc. You also can't use the gas truck's vacuum brake booster (diesels don't have throttles and don't create enough vacuum). Plus all the wiring harnesses for the motor and diesel specific transmission. |
|
There's a reason you don't see any gasoline trucks with turbos pulling trailers. Turbos generate TONS of heat, which means high intake temps and detonation. They're good for a short burst of power every now and then, but if you're looking to hook up a trailer and pull it with a turbocharged gasoline engine, you'll cook the motor on the first steep grade.
Turbo diesels on the other hand are made for just that. Diesels are incredibly efficient with heat and intake temps, and can put down the torque required to pull a trailer all day long. |
|
Quoted:
Is it possible to put a turbo charger on a 85 GMC with a V8 Gas under the hood? Sorry for the newbish question. Thanks Scott Short answer, yes. Long answer, it's probably not really practical or cost effective, in that with a Chevrolet V8, for a boost in power and performance it'd be easier and cheaper to go with a cam and a nice set of heads. |
|
I have a turbo in good shape from a 14L Caterpillar Diesel sitting on my desk as decoration right now
we can hook it up and see what happens |
|
Quoted: I have a turbo in good shape from a 14L Caterpillar Diesel sitting on my desk as decoration right now we can hook it up and see what happens not a whole lot. the volume of exhaust gas out of even a 454 would not be enough to turn the impeller on a turbo that big fast enough to make any gains. |
|
Quoted: I know, i was being facetious...Quoted: not a whole lot. the volume of exhaust gas out of even a 454 would not be enough to turn the impeller on a turbo that big fast enough to make any gains. I have a turbo in good shape from a 14L Caterpillar Diesel sitting on my desk as decoration right now we can hook it up and see what happens Friend worked at Borg Warner for a while and we've got boxes of rejected turbine/compressor wheels, and a few turbos from KP-35's up to the 140 on my desk... |
|
Quoted:
Quoted:
Sure, it is possible. How well it would function and how much you'd draw out of that motor in its stock form is a different question though. Whats your thoughts on that? Or would I be better off finding a Cummins or a Duramax for it? Scott Might have missed it but what it the main use of the truck? u r talking about turbo charging a gas v8 and then ask if it would be better to get a diesel? I'm thinking that you ar gonna be using for heavy towing/hauling? I would think that if that were the case then buying a diesel vs building a gas tow rig would be the better route. J- |
|
Quoted: There's a reason you don't see any gasoline trucks with turbos pulling trailers. Turbos generate TONS of heat, which means high intake temps and detonation. They're good for a short burst of power every now and then, but if you're looking to hook up a trailer and pull it with a turbocharged gasoline engine, you'll cook the motor on the first steep grade. Turbo diesels on the other hand are made for just that. Diesels are incredibly efficient with heat and intake temps, and can put down the torque required to pull a trailer all day long. |
|
85 should be carbed with a ECM IIRC.... Ditch the ECM and go with a 6-71 blower (roots style).....
|
|
Quoted:
85 should be carbed with a ECM IIRC.... Ditch the ECM and go with a 6-71 blower (roots style)..... But be ready for tranny work. |
|
Quoted:
Quoted:
Quoted:
Sure, it is possible. How well it would function and how much you'd draw out of that motor in its stock form is a different question though. Whats your thoughts on that? Or would I be better off finding a Cummins or a Duramax for it? Scott Might have missed it but what it the main use of the truck? u r talking about turbo charging a gas v8 and then ask if it would be better to get a diesel? I'm thinking that you ar gonna be using for heavy towing/hauling? I would think that if that were the case then buying a diesel vs building a gas tow rig would be the better route. J- General use, farm use, towing, back and forth to school, hauling girls around. I would love to go out and buy a powerstroke or a cummins (the only used trucks for sale around here) but i have no money. Scott |
|
Quoted:
Quoted:
Whats in it right now? 5.0 305 small block. Scott Swap in a small block 383 - 350 block/400 crank - and make sure the truck is geared properly for the tire size. Brian |
|
Put a cam in and clean up the heads a little. Maybe bolt on some headers. A blower would be SOOOOO much easier to put on a carb engine but turbo can be done. You would need a blowthru carb or find an old TPI setup. I was going to do a turbo TPI setup for an old camaro i had before i sold it.
|
|
Quoted: Quoted: I have a turbo in good shape from a 14L Caterpillar Diesel sitting on my desk as decoration right now we can hook it up and see what happens not a whole lot. the volume of exhaust gas out of even a 454 would not be enough to turn the impeller on a turbo that big fast enough to make any gains. Now if you had another hairdryer to feed it air... |
|
Quoted:
Put a cam in and clean up the heads a little. Maybe bolt on some headers. A blower would be SOOOOO much easier to put on a carb engine but turbo can be done. You would need a blowthru carb or find an old TPI setup. I was going to do a turbo TPI setup for an old camaro i had before i sold it. Educate me on a blower please? Scottq |
|
Quoted:
Before spending money engine performance/swap stuff have you checked your ring/pinion gear vs tire diameter to see if a r&p change might be what you need? Brian bolded, quoted underlined and reded for emphasis Bang for your buck NOTHING will beat a gear swap this thread is OVER |
|
Quoted:
I think imma just save up for a cummins. If you actually do any amount of substantial hauling and/or towing, you'll be much happier than with any gasser. |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.