Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
5899 Online
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
AR15.COM
bravocompany
My Account
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
bravocompany
aim
midwest
magpul
springfield
GS
Guns
cz
DFC
OSIGHT
vortex
JRH
RS
brownells
silencerShop
colt
primaryArms
Holosun
fightlite
skd
geissele
palmetto
5899 Online
bravocompany
cz
OSIGHT
skd
GS
Holosun
DFC
midwest
magpul
vortex
geissele
brownells
JRH
palmetto
RS
aim
Guns
primaryArms
colt
fightlite
silencerShop
springfield
AK Sponsor
Sponsor News Introducing TNVC's NEW and Exclusive Filmed SuperGain (FSG) and Chimera Panoramic Goggle Giveaway!
Site News The People of Virginia VS Grabigial BanBerger | ARFCOM News
8/17/2006 4:43:50 PM EDT
Before I start, I will admit I did ask this question before but because I am not ::coughshortbuscough:: special , by the time I got around to fixing it (I will also admit it took awhile) the thread was gone and I cannot reference that far back.  Sssoooo...
The axis that holds the trigger assembly upright by means of the two holes in the receiver just above the trigger keeps falling out of place after a couple squeezes of the trigger.  Does anybody have any idea what part is AWOL and where I can get another?
8/17/2006 5:10:06 PM EDT
[#1]
Tapco, K-VAR, DPHarms.com should all have the part.  Shepard's hook or crook or RSA replacement.




WASR trigger assembly will not stay in    

BeAsT762
Member
Joined :: September 2005
Post Number :: 23

VA, USA

OK, I can't post pictures so I will try to use my amazing knowledge of English (  ) to describe it. There is a little pin right above the trigger that holds the entire thing in place. When I pull the trigger two or three times, the pin falls out of it's hole on the ejection port side. I then have to play with it on the other side of the weapon to push it back into the hole. If I push and hold the pin from the non- ejection port side, I can pull the trigger as much as I please without a problem. Any possible solutions? I was thinking of getting permafix or something and applying it to the OUTSIDE of the weapon on the to sides of the pin, holding it in place. Does this sound like a bad idea?
Thank you!!!



--------------------------------------------------------------------------------
Posted :: 5/16/2006 12:06:19 PM
Last Edited :: 5/16/2006 12:08:43 PM by BeAsT762




legonas
Team Member
Ubergeek AK lover
Joined :: March 2002
Post Number :: 1310

SC, USA

the trigger retaining wire is missing / not installed correctly.

www.gunsnet.net/Linx310/fcgremoval.htm for more info

here is a drop in easier to use replacement; www.tapco.com/product_information.asp?number=AK0680&back=yes&dept=190&last=13


--------------------------------------------------------------------------------
"The universe is an infinitely faceted diamond, and each of our souls is reflected in its magnificence. Choose your facet, your window to the world, wisely."


--------------------------------------------------------------------------------
Posted :: 5/16/2006 12:22:04 PM
Last Edited :: 5/16/2006 12:23:38 PM by legonas




stargazer111
Member
Joined :: January 2006
Post Number :: 193

TX, USA

Make sure both pins of the trigger assy. go "in" on the left side of the receiver.



--------------------------------------------------------------------------------
Posted :: 5/16/2006 4:21:36 PM




BeAsT762
Member
Joined :: September 2005
Post Number :: 24

VA, USA

Great, thanks a lot!



--------------------------------------------------------------------------------
Posted :: 5/17/2006 11:42:38 AM



WASR trigger assembly will not stay in  
AK Sponsor
Pro2A
bravocompany
THBRD
LAPG
geissele
Faxxon
colt
CA
RS
palmetto
gray
blackhills
ar15com
silencerShop
SAS
brownells
ar15com
primaryArms
LAPG
cmmg
fightlite
ar15com