Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
AR Sponsor
6/16/2010 4:33:25 AM EDT
I finished the lower receiver on my first AR project yesterday. I been lurking on this board for about a year reading and learning and recently started posting. This is a great site. BRD has taken over.

Everything went together well with a couple exceptions. First the front screw on the Magpul trigger guard SUCKS. Mine screwed in about 3/4 of the way and my allen wrench broke off inside the screw, so now it sits with about 2mm of thread showing. The trigger guard itself is very secure and i dont think anyone would notice except me. My second problem was the safety seemed a bit out of spec. When installed with the handgrip and detent/spring it would NOT cycle to SAFE from FIRE, and after taking off/putting on/ looking the detent was getting hung inside the groove on the back because of a sharp burr on the edge. A little filing and drilling fixed that.

Now waiting on Rock River Arms upper assembly.

Parts List:
Daniel Defense Stripped Lower
DPMS parts kit
Hogue Grip
Magpul MOE 6-pos stock
Magpul Trigger Guard
Rock River Arms 16" CAR A4 upper/assembly 5.56 HBAR, 1/9 chrome lined, chromed BCG
Magpul MOE handguard with 11-slot rails
YHM muzzle brake
Magpul MBUS rear sight
Magpul PMAGs
http://dl.dropbox.com/u/5209291/Lower%20and%20handguard.jpg
http://dl.dropbox.com/u/5209291/Hogue%20Handgrip.jpg
http://dl.dropbox.com/u/5209291/Daniel%20Defense%20Lower.jpg
http://dl.dropbox.com/u/5209291/Magpul%20MOE%20and%20YHM%20brake.jpg

More pics when upper gets here!
6/16/2010 5:53:10 AM EDT
[#1]
Sweet! I'm in the process of finishing up mine as well.

Doesn't it suck waiting for parts? Waiting on a few myself
6/30/2010 4:33:37 AM EDT
[#2]
Rock River Barreled Upper arrived yesterday. Snapped right together and I have to say I am quite please with how snug the fit is between the RRA upper and DD lower. Both A++ quality. Switched out to YHM muzzle brake. Replaced CAR handguard with Magpuol MOE unit. The only range I could get to yesterday was an indoor 25yd range, so target is my first mag. The thing was remarkably close to where I wanted the BUIS from the factory!! I attempted to keep the BUIS at a 50yd zero (while only shooting at 25yds). Optics to come soon. BUIS only for now.

And me taking the first shot with the new black rifle!!

http://dl.dropbox.com/u/5209291/AR15action.jpg
http://dl.dropbox.com/u/5209291/AR15backview.jpg
http://dl.dropbox.com/u/5209291/AR15Magpulcomplete2.jpg
http://dl.dropbox.com/u/5209291/Ar15Magpulcomplete.jpg
http://dl.dropbox.com/u/5209291/UpperLower.jpg
http://dl.dropbox.com/u/5209291/MagpulYHMbrake.jpg
http://dl.dropbox.com/u/5209291/Firsttarget.jpg



6/30/2010 4:54:55 AM EDT
[#3]
Nice rifle.
6/30/2010 6:05:01 AM EDT
[#4]
nice stick.. you'll enjoy and i guarentee it wont be one and done.. i just finished my first and about to order a lower and lpk kit from spikes to start a spr build.. cant wait!
6/30/2010 9:05:10 AM EDT
[#5]
Nice rifle.
6/30/2010 11:44:58 AM EDT
[#6]
Front screw on trigger guard did the same for me as well. Have to EZ out the thing
7/6/2010 5:52:57 AM EDT
[#7]
Nice build
7/6/2010 9:58:46 AM EDT
[#8]
Very nice indeed - good job!
7/12/2010 4:23:26 PM EDT
[#9]
added my scope and a tangodown forend grip

http://dl.dropbox.com/u/5209291/Ar15HandgripScope.jpg
AR Sponsor