Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
4175 Online
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
AR15.COM
bravocompany
My Account
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
skd
GS
silencerShop
OSIGHT
palmetto
springfield
JRH
RS
geissele
cz
bravocompany
DFC
Holosun
aim
primaryArms
brownells
magpul
colt
Guns
midwest
vortex
fightlite
4175 Online
vortex
silencerShop
bravocompany
JRH
Guns
magpul
fightlite
DFC
colt
palmetto
Holosun
OSIGHT
aim
cz
brownells
skd
springfield
geissele
midwest
GS
RS
primaryArms
AR Sponsor
Site News Could You Have Stopped This? Vegas Shooting Analysis with Attorneys on Retainer
Sponsor News Introducing TNVC's NEW and Exclusive Filmed SuperGain (FSG) and Chimera Panoramic Goggle Giveaway!
1/12/2013 6:09:00 PM EDT
I'm sure a lot of you have seen me around asking questions lately as I am COMPLETELY new to AR's. I do not have enough experience to know what tolerances are considered "normal". (I am an AK guy). With that said, I have a MEGA lower and the Magpul Enhanced Triggerguard has some side to side movement. Almost as if it is not wide enough in between the ears AND the receiver. I searched the archives and found one other person that had the same experience with a MEGA lower.

Maybe it's just MEGA? Or, is it considered "OK" to have a wee bit of rattle on the trigger guard?

I appreciate the help, fellas

- nsz

ETA: To clarify, it moves side to side on both the roll pin AND the set screw...
1/13/2013 1:33:41 PM EDT
[#1]
bump? really? no one?
1/13/2013 1:50:39 PM EDT
[#2]
As long as your pins are in all the way, I wouldn't worry.  That's not a stress point, and a little lateral movement is acceptable.
1/13/2013 1:54:28 PM EDT
[#3]
Quoted:
As long as your pins are in all the way, I wouldn't worry.  That's not a stress point, and a little lateral movement is acceptable.


Alright cool. Thank you sir!
1/13/2013 3:16:15 PM EDT
[#4]
If it bothers you that much you could shim it.
1/13/2013 3:37:14 PM EDT
[#5]
Quoted:
If it bothers you that much you could shim it.


nah, J B weld instead.
1/13/2013 8:46:16 PM EDT
[#6]
Also, I know it sounds counter-intuitive, but make sure you have not overtightened the screw for the trigger guard...
1/13/2013 8:52:17 PM EDT
[#7]
Could always use the grip of shame....
1/13/2013 8:57:04 PM EDT
[#8]
Quoted:
Also, I know it sounds counter-intuitive, but make sure you have not overtightened the screw for the trigger guard...


I made sure NOT to overtighten it.
1/13/2013 9:55:34 PM EDT
[#9]
Quoted:
Could always use the grip of shame....


Nooooooooooooo!!!

1/14/2013 8:17:37 PM EDT
[#10]
Quoted:
Quoted:
Also, I know it sounds counter-intuitive, but make sure you have not overtightened the screw for the trigger guard...


I made sure NOT to overtighten it.


I would still try backing it out a half to full turn and see if that improves the situation.

1/14/2013 8:24:52 PM EDT
[#11]
maybe some blue thread locker?
1/14/2013 9:25:11 PM EDT
[#12]
We have a Mega lower with the MP Enhanced trigger guard and there is no play at all.

Quoted:
Could always use the grip of shame....

I do not like the grip of shame.
1/14/2013 10:12:13 PM EDT
[#13]
I took out the set screw, cleaned and degreased it, replaced the blue thread lock with fresh stuff and put it back in. It appears to be much tighter now. Thank you everyone for the help!
AR Sponsor
ar15com
springfield
RS
silencerShop
SAS
ar15com
cmmg
fightlite
THBRD
blackhills
bravocompany
Pro2A
Faxxon
brownells
primaryArms
gray
LAPG
palmetto
geissele
ar15com
LAPG
colt