Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
7063 Online
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
AR15.COM
bravocompany
My Account
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
palmetto
fightlite
Holosun
Guns
skd
OSIGHT
brownells
geissele
aim
midwest
colt
cz
GS
springfield
DFC
JRH
vortex
RS
silencerShop
magpul
primaryArms
bravocompany
7063 Online
geissele
colt
silencerShop
DFC
bravocompany
vortex
RS
springfield
JRH
brownells
aim
Guns
Holosun
GS
OSIGHT
primaryArms
midwest
palmetto
skd
fightlite
magpul
cz
AR Sponsor
Site News Could You Have Stopped This? Vegas Shooting Analysis with Attorneys on Retainer
Sponsor News Introducing TNVC's NEW and Exclusive Filmed SuperGain (FSG) and Chimera Panoramic Goggle Giveaway!
5/10/2009 1:26:00 PM EDT
Hey guys,



I have a 20" that I want to put a bipod on.  I am keeping the standards rifle handguards on this, so what are my options for mounting a bi-pod.  I don't think I cared for the barrel mounts..



What other options do I have here?
5/10/2009 4:07:15 PM EDT
[#1]
Swivel Stud or Bayonet Lug are your best options.
You can get one that clamps directly to the barrel but it may scratch it.
5/10/2009 7:21:08 PM EDT
[#2]
I made one with a Uncle Mikes QD stud, common washer and common lock nut.  Put inside a regular HG and attached the Harris to it then tightened the whole thing.  Rock solid and cheap and can be completely removed.
5/11/2009 2:48:21 AM EDT
[#3]


Harris makes an adaptor for handguards.

HB2 - Flange Nut - Allows mounting of stud on hollow fore-ends $12.00
5/11/2009 2:03:31 PM EDT
[#4]
That looks nice but I was too cheap to buy one and pay shipping when I had the stud from a Rem 700P on hand.
5/11/2009 5:00:57 PM EDT
[#5]




Quoted:

http://www.harrisbipods.com/IMG/HB2.jpg



Harris makes an adaptor for handguards.



HB2 - Flange Nut - Allows mounting of stud on hollow fore-ends $12.00


So I take it this lays on the inside of the handguard, and the stud srews up through the bottom, keeping it tight...





I have a sling mount on the rifle.. any way to modify that to attach the bipod. Sorry if these are stupid questions, I just don't have any knowledge when it comes to bipods - never used on before
5/11/2009 7:52:49 PM EDT
[#6]
200 views and only 3 people can reply?



What do all of you guys out there with bipods use if you don't have rails.  I'm wanting to order this thing up...  what route should I go with?
5/11/2009 8:00:14 PM EDT
[#7]
I would go with the stud combo in the pix provided IF it would not crush my handguard liner when it was made tight.  My washer went between the guard and liner.
AR Sponsor
cmmg
RS
SAS
bravocompany
blackhills
LAPG
palmetto
ar15com
Faxxon
brownells
colt
CA
Pro2A
gray
ar15com
silencerShop
THBRD
fightlite
primaryArms
LAPG
springfield
geissele