Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
8/9/2011 5:47:40 AM EDT
Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?
8/9/2011 5:55:57 AM EDT
[#1]
Lower cost of operation.




8/9/2011 5:58:48 AM EDT
[#2]
Ummm,   no.


A 220/240 unit uses twice as much electicity as a 110/120v




















8/9/2011 6:04:01 AM EDT
[#3]





Quoted:



Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?



They don't have to pull as many amps for the same work.  But you have to have a special power line run to the unit.





 
8/9/2011 6:05:31 AM EDT
[#4]
Quoted:

Quoted:
Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?

They don't have to pull as many amps for the same work.  But you have to have a special power line run to the unit.
 


Yes but they use twice as many volts so it is the same in the end. The Kw-hr amount is the same.
8/9/2011 6:11:50 AM EDT
[#5]



Quoted:



Quoted:




Quoted:

Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?


They don't have to pull as many amps for the same work.  But you have to have a special power line run to the unit.

 




Yes but they use twice as many volts so it is the same in the end. The Kw-hr amount is the same.


I understand that.



 
8/9/2011 6:14:48 AM EDT
[#6]
Quoted:
Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?


If you want a unit with heating, then 220/240V.

I have 120V 12000 BTU.  10 amp draw.  Works well for 500 square feet.

I looked at 220V and it had 5 amp draw for 18000 BTU.

8/9/2011 6:43:36 AM EDT
[#7]
Quoted:
Aside from the size/ higher BTU rating is there any advantage to a 220/240V unit vs a 110/120 unit?


The larger models tend to start easier on 220/240 volts. If you have wiring that's a little undersized or have low AC supply voltage, the fact that a 220/240 volt model will draw half as much current can make a difference in getting the compressor started.

The downside is that you can't easily move a 220/240V unit to another window, unless you have 220/240V wall outlets near every window. Also, not all generators produce 220/240V - a consideration if you ever want to power a window unit with a generator during an extended power outage.
8/9/2011 6:45:27 AM EDT
[#8]
No.

It's about amperage draw.

Once you get to about 12,000 BTU units, you have to go to 240V.

IIRC, an 8000 BTU unit draws about 7.5 amps.
8/9/2011 6:46:48 AM EDT
[#9]
if you rent, a 240V would be idiotic. no one has outlets wired for that.
8/9/2011 6:54:29 AM EDT
[#10]
Btu's require a certian KW load to achieve, the voltage of the unit wont change the cost.

I have 3 110v units and love them.  Pretty powerful for the size.  1 cools my 20x30 garage very well, and its a little baby unit.
8/9/2011 6:57:03 AM EDT
[#11]
Thanks guys, will have to install wiring either way. did not consider the heating aspect of it either. now I have MORE to look into
8/9/2011 7:12:20 AM EDT
[#12]
Savings is in reduced surges when starting up the compressor.   Your electric bill is based on how many amp hours you use, plus peaks (surges) like when you weld or fire up compressors.  By going to 220, you typically reduce the peak demands.


8/9/2011 7:17:43 AM EDT
[#13]
Ohm's Law,....Learn it, Live it, Love it.
8/9/2011 8:58:48 AM EDT
[#14]



Quoted:


Savings is in reduced surges when starting up the compressor.   Your electric bill is based on how many amp hours you use, plus peaks (surges) like when you weld or fire up compressors.  By going to 220, you typically reduce the peak demands.



We only measure demand on larger commercial customers.  Other utilities might be different, but none I am aware of.