User Panel
Which way does the ratchet/wrench swing? Therein lies your answer. Assuming you're looking straight at the bolt/nut.
|
|
|
|
It's always relative to the top as you are facing the bolt/nut you are manipulating. Once you do it a hundred times (within a reasonable amount of time...not once a year for 100 years), and say it to yourself, you should be able to see it. Ya know, it takes doing something 21 days (in a row, I think) to create a habit.
And if yur rill smurt, u cud evun cee hit buckword. |
|
Quoted: Right hand rule https://upload.wikimedia.org/wikipedia/commons/thumb/b/b9/Right-hand_screw_rule.svg/1200px-Right-hand_screw_rule.svg.png View Quote but what if you're left handed? |
|
Quoted: Quoted: Just wait until you run across a vehicle that has left-handed lug nuts, but only on the left side of the vehicle. I about gave myself a hernia trying to get the lug nuts off the drivers side wheel on my M35A2. I learned the next day that they went the other way. |
|
Quoted: I knew my left from right - that was not the problem. I remember my dad telling me that while teaching me to do an oil filter or something when I was single digit in years. The top is turning one way (left), and the bottom the opposite (right)! It sounded simple, so I was afraid to question it. Clockwise and counterclockwise would have made more sense to me. Dang near gave me a complex. And delayed my understanding of it for years CSB View Quote I am 100% with you OP. |
|
|
|
|
Quoted: That would never have occurred to me as an explanation, but it makes sense. I have gotten in trouble with this before. Okay, but what about those little wireless mice with the power switch - but it's not labeled on or off outside the switch, it's labeled on or off on the sliding part of the switch. You slide the switch to the right, and it displays a green 'ON' in the newly exposed part of the switch slider. You slide it the left, and it displays a red 'OFF'. (Edited to match the image). Which direction is on, and which off? https://www.lifewire.com/thmb/2CM0IMCJhn80VnPchKZj0fBFrUY=/1500x0/filters:no_upscale():max_bytes(150000):strip_icc()/002_pair-with-logitech-mouse-5184314-8df193eb4d24464cb5d12a260d752be4.jpg View Quote Mine slides up and down. FUCK!! |
|
|
Quoted: Do any still do that? Can't remember what car I had that was like that. 72 charger ? View Quote View All Quotes View All Quotes Quoted: Quoted: Just wait until you run across a vehicle that has left-handed lug nuts, but only on the left side of the vehicle. Do any still do that? Can't remember what car I had that was like that. 72 charger ? My '68 Coronet was like that. |
|
Quoted: I agree, it makes no sense, there is no left or right on a circle. View Quote Dat chirality tho… |
|
I’ll just add that it was explaining to me as “righty tightly, lefty loosely”, not the other way around
|
|
|
Quoted: Right hand rule https://upload.wikimedia.org/wikipedia/commons/thumb/b/b9/Right-hand_screw_rule.svg/1200px-Right-hand_screw_rule.svg.png View Quote This is best rule. It helped my boy who's dyslexic. When you're upside down and backwards, under a car and working on the back side of something toward you, this is a useful tool. You really want to get messed with? Start cutting right hand threads on a lathe with your tool upside down so you can go backwards. |
|
|
Try explaining NESW to someone who only knows left and right. You can’t make them understand those people are the ones who drive off the cliff because GPS told them to.
|
|
Quoted: Try explaining NESW to someone who only knows left and right. You can’t make them understand those people are the ones who drive off the cliff because GPS told them to. View Quote Which mnemonic device do you use? Never Eat Shredded Wheat? Never Eat Sour Watermelon? Never Eat Soggy Waffles? |
|
|
|
Looking at the bolt head, imagine that it's a wheel.
If you're tightening the bolt, the wheel would travel right. If you're loosening it, the wheel would travel left. If it's reverse-threaded, then it sucks and I hate it. |
|
|
Quoted: Looking at the bolt head, imagine that it's a wheel. If you're tightening the bolt, the wheel would travel right. If you're loosening it, the wheel would travel left. If it's reverse-threaded, then it sucks and I hate it. View Quote You dont really have to explain it, we get it now. Its when we were 3. |
|
|
Grown millwrightsI I work with have a hard time with it too don't put them on a flange with bolts running different ways either
|
|
|
Quoted: Try explaining NESW to someone who only knows left and right. You can’t make them understand those people are the ones who drive off the cliff because GPS told them to. View Quote Tell 'em cowboys always ride off into the sunset in the wild WEST (approximately). Sunset = WEST. The rest follows from there. Sunrise = EAST. North = Right (facing West) South = left (facing West) |
|
Quoted: but what if you're left handed? Right hand rule, not dominant hand rule. |
|
Quoted: Right hand rule https://upload.wikimedia.org/wikipedia/commons/thumb/b/b9/Right-hand_screw_rule.svg/1200px-Right-hand_screw_rule.svg.png View Quote Attached File |
|
Quoted: Looking at the bolt head, imagine that it's a wheel. If you're tightening the bolt, the wheel would travel right. If you're loosening it, the wheel would travel left. View Quote You assume a frame of reference that starts at top dead center. That frame of reference is not standard. You could be starting from a wrench applied below (6 o'clock) in which case left movement tightens, or you could be viewing the fastener from behind (mirror image) which again defies the lefty loosie - righty tighty mantra. Righty tighty is simple minded; people with a higher intellectual grasp understand why it is wrong. |
|
Quoted: Wrong. You assume a frame of reference that starts at top dead center. That frame of reference is not standard. You could be starting from a wrench applied below (6 o'clock) in which case left movement tightens, or you could be viewing the fastener from behind (mirror image) which again defies the lefty loosie - righty tighty mantra. Righty tighty is simple minded; people with a higher intellectual grasp understand why it is wrong. View Quote You bring up a good point about spacial recognition. I'm able to imagine something and rotate it in my mind as if it were a 3d model, but apparently not everyone is capable of that. I wonder how many people are out there where this doesn't come naturally for them? |
|
Quoted: Driver's side is left side unless you're a Brit or live in one of the other places that don't drive on the correct side of the road. View Quote View All Quotes View All Quotes Quoted: Quoted: Left looking at the front or the back? We should have port and starboard for cars too. |
|
Quoted: You bring up a good point about spacial recognition. I'm able to imagine something and rotate it in my mind as if it were a 3d model, but apparently not everyone is capable of that. I wonder how many people are out there where this doesn't come naturally for them? View Quote Sooooooooooooooo many people |
|
Quoted: Wrong. You assume a frame of reference that starts at top dead center. That frame of reference is not standard. You could be starting from a wrench applied below (6 o'clock) in which case left movement tightens, or you could be viewing the fastener from behind (mirror image) which again defies the lefty loosie - righty tighty mantra. Righty tighty is simple minded; people with a higher intellectual grasp understand why it is wrong. View Quote @14point5 Have you heard of the dunning-kruger effect? |
|
Those of you saying it’s a circle motion you can’t go left or right….
You’re the degenerate drivers that fuck up at the roundabouts. |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.