User Panel
Posted: 2/13/2011 3:50:10 PM EDT
You know how some barrel and upper combos can be a pain to get the gas tube holes to line up? Well I ran into a real hard case today.
Either super tight or hand tight, no in between. I'm going to swap the barrel to another upper to see if it helps. But does any one make shims that can be used to help align problem barrels? |
|
I use a big flat diamond sharping stone to take a bit off the barrel nut. That loosens up the "Super tight" position.
I guess you could use some fine emery cloth on a nice flat surface to do the same thing. Keep checking for fit. I'm guessing you tried the repeated tighten and loosen method already. |
|
Yep, tried the tighten and loosen several times. Close but no cigar. How do you remove an even amount from the face of the barrel nut? I've installed a few dozen barrels and have never seen one this tough. Real bad.
|
|
Quoted:
Yep, tried the tighten and loosen several times. Close but no cigar. How do you remove an even amount from the face of the barrel nut? I've installed a few dozen barrels and have never seen one this tough. Real bad. You can't! This is bad advice, really bad advice. This topic keeps coming up but people just won't listen. Where did a torque wrench come into play during surgery? Torque that nut to 30 ft lbs then tighten it to the next notch in the barrel nut. It's that simple. |
|
Quoted:
Quoted:
Yep, tried the tighten and loosen several times. Close but no cigar. How do you remove an even amount from the face of the barrel nut? I've installed a few dozen barrels and have never seen one this tough. Real bad. You can't! This is bad advice, really bad advice. This topic keeps coming up but people just won't listen. Where did a torque wrench come into play during surgery? Torque that nut to 30 ft lbs then tighten it to the next notch in the barrel nut. It's that simple. That's part of the problem. It's the strangest thing i have seen. Line up one notch, then over 80 pounds to the next and it will not line up. Back it up to the previous notch and it's hand tight at best. It goes from super tight to loose. I can turn the barrel by hand in the receiver when lined up. I can lap it I guess. |
|
The top value is irrelevant. Just tighten it to the next notch.
|
|
Quoted: The top value is irrelevant. Just tighten it to the next notch. No it's not. You go too far past that 80 ft-lbs and you'll crack your upper. |
|
lap upper or try another nut. Its not like the threads on the nut are indexed to the area you grab with the wrench.
Mine was a PITA too, and I told myself next time, Im building a upper, I will get 2 or 3 barrel nuts so I can pick a better fit. |
|
Quoted:
lap upper or try another nut. Its not like the threads on the nut are indexed to the area you grab with the wrench. Mine was a PITA too, and I told myself next time, Im building a upper, I will get 2 or 3 barrel nuts so I can pick a better fit. Damn, I keep forgetting this option. Well done |
|
Quoted:
Quoted:
lap upper or try another nut. Its not like the threads on the nut are indexed to the area you grab with the wrench. Mine was a PITA too, and I told myself next time, Im building a upper, I will get 2 or 3 barrel nuts so I can pick a better fit. Damn, I keep forgetting this option. Well done This is a YHM float tube with it's own nut. Only one I have for that type of tube. But good idea if it was a standard build. Of course I've never had this extreme issue with a factory style nut. |
|
Quoted: Call YHM and ask for another nut.Quoted: Quoted: lap upper or try another nut. Its not like the threads on the nut are indexed to the area you grab with the wrench. Mine was a PITA too, and I told myself next time, Im building a upper, I will get 2 or 3 barrel nuts so I can pick a better fit. Damn, I keep forgetting this option. Well done This is a YHM float tube with it's own nut. Only one I have for that type of tube. But good idea if it was a standard build. Of course I've never had this extreme issue with a factory style nut. |
|
Quoted: Yep, tried the tighten and loosen several times. Close but no cigar. How do you remove an even amount from the face of the barrel nut? I've installed a few dozen barrels and have never seen one this tough. Real bad. With a lathe and a boring bar. |
|
Quoted:
Are you using moly grease on it? This is my very first question in this sort of situation. Any decent anti-seize grease is absolutely essential, and "the right" grease pretty darn important. The "30-80 ft/lb" torque spec is based on a standard barrel nut being assembled with the appropriate MIL-G grease. The TM calls for tighten/torque/loosen/retorque if you can't get the desired number, and some people have reported repeating the process more than 10 times. But the next issue is what YHM says about the torque spec for THAT unit. If they say "use the standard torque spec," then that's fine. They may ask for something different, based on the materials and treatment of the parts. Also, how are you connecting the torque wrench to the YHM barrel nut? That could make a difference. |
|
Easiest way is what has already been said. Lap the front of the upper. I use 600 grit paper on the flat side of a large socket. Most time you will not even go through the anodizing before it will allow the notch to line up. You only have to remove a .001 to .0015.
I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea. 160$ barrel in the trash |
|
Quoted:
Why do folks not post all the facts from the get go So the thread can go 3 times longer than it needs to be. |
|
Quoted:
Quoted:
Why do folks not post all the facts from the get go So the thread can go 3 times longer than it needs to be. Does the type of nut really matter? I just installed an SAR, and this tube on another upper. The problem would be the same regardless of who made the nut or what rail, no? I just never ran into one this tough before. Tell me exactly how the fact that the fucking nut is a YHM has extended this three times longer? The lapping and other advice remains the same. |
|
Why not simply torque over minimum, then remove the offending nub?
Later, Chrome... |
|
Quoted:
Easiest way is what has already been said. Lap the front of the upper. I use 600 grit paper on the flat side of a large socket. Most time you will not even go through the anodizing before it will allow the notch to line up. You only have to remove a .001 to .0015. I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea. 160$ barrel in the trash DSA may replace the barrel for you, or have another alignment pin pressed in it for you. Cal them before scrapping it. |
|
Randall at AR15barrels.com offers shims to index the barrel nut. That being said, Randall is MIA from this web site because of several questionable business transactions!!!
Link to barrel indexing shims FAQ If you need further info on Randall, contact Aimless (site staff) |
|
Quoted:
Randall at AR15barrels.com offers shims to index the barrel nut. That being said, Randall is MIA from this web site because of several questionable business transactions!!! Link to barrel indexing shims FAQ If you need further info on Randall, contact Aimless (site staff) I didn't think Randall was still in business. Just noticed in my Spikes directions that they mention shims for the SAR if you are using a piston with that rail. |
|
Quoted:
Quoted:
Easiest way is what has already been said. Lap the front of the upper. I use 600 grit paper on the flat side of a large socket. Most time you will not even go through the anodizing before it will allow the notch to line up. You only have to remove a .001 to .0015. I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea. 160$ barrel in the trash DSA may replace the barrel for you, or have another alignment pin pressed in it for you. Cal them before scrapping it. Nothing wrong with the alignment pin. The whole extension starting unscrewing becuase it was not tightened properly. When you use barrel blocks as the barrel nut is tighened against the barrel extension it is trying to unscrew the extension. Thats why you have the 80 FT LB max in the book to stop at. |
|
Quoted:
Lapped the receiver, problem solved. Thanks guys. Excellent. Glad to hear it was that simple. The front end of the upper itself has really well defined dimensions. Those dimensions can be altered by uneven anodizing, which can make it difficult to impossible to get the right torque. A tiny bit of lapping solved your problem, rather nicely illustrating this situation. |
|
Quoted:
When you use barrel blocks as the barrel nut is tighened against the barrel extension it is trying to unscrew the extension. Thats why you have the 80 FT LB max in the book to stop at. I had never made that connection, but you're right. Thanks for the educational tidbit! |
|
Silly me, I thought the pin went through the extension into the barrel so it couldn't rotate out.
http://www.ar15barrels.com/making.shtml Check the third pic from the bottom. Barrel nuts will loosen, it's the whole point of the star cuts - to stop rotation by snagging the gas tube. I doubt Stoner would go to the trouble of doing that and ignore pinning the barrel extension. If it unscrews, you lose headspace and catastrophe is imminent. As for shims, just lap the upper, it not only squares it, the nut will rotate to line up without having to stack shims - and have it still out of square. Just Go Slow and Check Often. It doesn't take much. |
|
Quoted:
I use a big flat diamond sharping stone to take a bit off the barrel nut. That loosens up the "Super tight" position. I guess you could use some fine emery cloth on a nice flat surface to do the same thing. Keep checking for fit. I'm guessing you tried the repeated tighten and loosen method already. Barrel nut?? How did you get down to the shoulder that interfaces with the barrel extension? |
|
Quoted:
Silly me, I thought the pin went through the extension into the barrel so it couldn't rotate out. http://www.ar15barrels.com/making.shtml Check the third pic from the bottom. Barrel nuts will loosen, it's the whole point of the star cuts - to stop rotation by snagging the gas tube. I doubt Stoner would go to the trouble of doing that and ignore pinning the barrel extension. If it unscrews, you lose headspace and catastrophe is imminent. As for shims, just lap the upper, it not only squares it, the nut will rotate to line up without having to stack shims - and have it still out of square. Just Go Slow and Check Often. It doesn't take much. You should probably just stop there |
|
Quoted:I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea.
Sounds like a better case for using the right tool for the job than advocating a torque value. You're torquing a nut in reference to the upper, the upper, not the barrel should be clamped. Barrel blocks are for installing muzzle devices. |
|
Quoted:
Quoted:I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea.
Sounds like a better case for using the right tool for the job than advocating a torque value. You're torquing a nut in reference to the upper, the upper, not the barrel should be clamped. Barrel blocks are for installing muzzle devices. The index pin basically locks the barrel to the upper, so you're not doing anything different from clamping the upper when you use a barrel vise. Except of course not putting all the torque on the aluminum upper and instead putting it on the steel barrel. |
|
Quoted: Quoted:I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea. Sounds like a better case for using the right tool for the job than advocating a torque value. You're torquing a nut in reference to the upper, the upper, not the barrel should be clamped. Barrel blocks are for installing muzzle devices. Army TM9-1005-249-23P shows that the barrel vise is the proper tool for the job. Actually it never even mentions an upper vise block. |
|
Quoted:
Quoted:
Quoted:I had a barrel extension unscrew yesterday on a DSA barrel using barrel blocks with the wrench set at 70 FT LBS. Going over the manual stated 80 LBs is not a good idea.
Sounds like a better case for using the right tool for the job than advocating a torque value. You're torquing a nut in reference to the upper, the upper, not the barrel should be clamped. Barrel blocks are for installing muzzle devices. Army TM9-1005-249-23P shows that the barrel vise is the proper tool for the job. Actually it never even mentions an upper vise block. Neither does, U.S. MC TM 05538C-23&P/2 |
|
Upper blocks give the dreaded "My rear sight is all the way to the left". Never had but two unscrew. One was an Olympic and then this one.
|
|
Quoted:
Silly me, I thought the pin went through the extension into the barrel so it couldn't rotate out. http://www.ar15barrels.com/making.shtml Check the third pic from the bottom. Barrel nuts will loosen, it's the whole point of the star cuts - to stop rotation by snagging the gas tube. I doubt Stoner would go to the trouble of doing that and ignore pinning the barrel extension. If it unscrews, you lose headspace and catastrophe is imminent. As for shims, just lap the upper, it not only squares it, the nut will rotate to line up without having to stack shims - and have it still out of square. Just Go Slow and Check Often. It doesn't take much. You post a link to how one person does their barrels. But that is not how any factory ones I have seen are done. The pin is just pressed against the threads. |
|
Quoted:
Quoted:
Silly me, I thought the pin went through the extension into the barrel so it couldn't rotate out. http://www.ar15barrels.com/making.shtml Check the third pic from the bottom. Barrel nuts will loosen, it's the whole point of the star cuts - to stop rotation by snagging the gas tube. I doubt Stoner would go to the trouble of doing that and ignore pinning the barrel extension. If it unscrews, you lose headspace and catastrophe is imminent. As for shims, just lap the upper, it not only squares it, the nut will rotate to line up without having to stack shims - and have it still out of square. Just Go Slow and Check Often. It doesn't take much. You post a link to how one person does their barrels. But that is not how any factory ones I have seen are done. The pin is just pressed against the threads. Raises an interesting question. This poster third from the bottom claims Colt and Sabre go further: http://www.weaponeer.net/forum/forum_posts.asp?TID=10825 Think about it, a barrel that unthreads from the extension basically loses it's headspace right there. |
|
Quoted: My bad. I'm not sure where my head was at the time, even reading it now I can't for the life of me figure out just what the hell I was talking about. Quoted: I use a big flat diamond sharping stone to take a bit off the barrel nut. That loosens up the "Super tight" position. I guess you could use some fine emery cloth on a nice flat surface to do the same thing. Keep checking for fit. I'm guessing you tried the repeated tighten and loosen method already. Barrel nut?? How did you get down to the shoulder that interfaces with the barrel extension? I recall talking to a buddy in MI about doing this to the prop nuts on his boat because he couldn't get the lock nut down far enough to get the cotter key back in. But how the hell I transferred this conversation to a barrel nut is beyond me. Getting old has it's moments, this may have been one of them. |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.