Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 12/10/2003 6:37:38 PM EST
[Last Edit: 12/11/2003 6:33:47 PM EST by Scooter1942]
I purchased an ACE skeleton stock for one of my AR's this weekend and I really am pleased with the purchase. However, there's one thing about the set-up that I don't like (for purely cosmetic reasons) and that's the foam pad that covers the buffer tube. Comfortable...yes, but I don't like how it "almost" interferes with the charging handle and I don't like how it looks kinda cheap and prone to damage, soaking up sand, water, etc.

So, I pulled mine off and replaced it with a piece of bicycle tubing. I cut up one of my 1.5x26 mountain bike tubes and it slides over with perfectly. A smaller one might fit a bit tighter and prevent twisting or movement, but I used a bit of spray adhesive (hair spray would do) and it's on there nice and tight. The rubber provides some insulation, but the cool thing, is now it looks like a real skeleton stock. The foam pad filled the empty space and made it look kinda cheesy, IHO.

A super cheap change, that not only looks cool, but is cheap and easy to replace when needed.





And one of my "military" family...since I had the camera out.

Link Posted: 12/10/2003 6:47:03 PM EST
Scooter could you post a picture? Thanks!
Link Posted: 12/10/2003 7:06:04 PM EST
i second that...pictures please! lots of them! Thanks for the tip.
Link Posted: 12/10/2003 7:56:15 PM EST
There is another cool ACE stock on page 15 of the AR picture thread. It looks that instead of a foam tube, the owner used braided rope (kinda like on a knife handle)
Link Posted: 12/10/2003 10:27:01 PM EST
I totally agree with your assessment of the foam padding. However, I would like to have a bare buffer tube that somewhat matches the matte anodizing of the stock… I can’t find one; all the ones I have found are somewhat “glossy”. Oh well, I hear bbq paint works magic.
Link Posted: 12/10/2003 10:54:52 PM EST
A suitably colored prophylactic might add a bit of conversational interest to your ACE stock. I believe a 'ribbed' model would help insure a proper cheek weld. (Might be a little slippery though.) 5sub
Link Posted: 12/10/2003 11:05:48 PM EST
[img]http://photos.ar15.com/ImageGallery/Attachments/DownloadAttach.asp?iImageUnq=20404[/img]
Link Posted: 12/11/2003 2:43:59 AM EST
That is pretty dang cool AZ-K9!
Link Posted: 12/11/2003 5:34:47 AM EST
Yes, I'll try to post some pictures tonight. I like the rope, but I like there to be an "air" space between the top and bottom tube, similiar to para stocks on some other weapons systems. The nice thing about the tire tube, is the rubber takes on a nice matte finish, especially if you wipe it down with some Goo Gone. I did this to clean off a bit of adhesive I got on the outside of the tube. From a distance of a foot or two, you cannot tell that it is a rubber tube. In fact, it actually matches my Rock River lower almost exactly.
Link Posted: 12/11/2003 5:58:24 AM EST
Originally Posted By new-arguy: That is pretty dang cool AZ-K9!
View Quote
Ditto.
Link Posted: 12/11/2003 8:20:26 AM EST
here is my ACE solution. parachord: [img]www.cs.uwf.edu/~rharper/ar15s.jpg[/img]
Link Posted: 12/11/2003 10:34:44 AM EST
[Last Edit: 12/11/2003 10:48:47 AM EST by Tman]
Another variant of the paracord wrap. I really like the look/feel. [img]http://im1.shutterfly.com/procserv/47b3cf09b3127cce828a622a5bb00000001610[/img] [img]http://im1.shutterfly.com/procserv/47b3cc30b3127cce838c580bdafd0000001610[/img]
Link Posted: 12/11/2003 1:18:50 PM EST
What is your method of securing both ends of the cord ? Thanks
Link Posted: 12/11/2003 2:44:00 PM EST
Make a loop as shown and wrap tightly from butt end. Place end through "loop end" and pull cord tight from the butt. Cut ends "short" and melt using a lighter. Keeping the ends and return cord on bottom will leave neat ends that are durable and hardly noticeable. [img]http://im1.shutterfly.com/procserv/47b3cc30b3127cce8388f26fdacd0000001610[/img]
Link Posted: 12/11/2003 3:58:59 PM EST
Thank you, It looks like a variation of a hangmans noose. Thanks again
Link Posted: 12/11/2003 4:02:55 PM EST
Pretty cool. I just used some OD thread and put a few stiches in the parachord to hold it in place. Then melted the ends of the chord.
Link Posted: 12/11/2003 5:29:29 PM EST
The rubber tubing is unique. So far though, I prefer the para chord. Where do I get "Parachord 101"?
Link Posted: 12/11/2003 5:37:16 PM EST
I'm trying to get pics up of the bicycle tube on the ACE stock. I can figure out how to put (a) rubber on by rifle but I can't figure out how to post pics...and all that money spent on graduate school shot to Hell!
Link Posted: 12/11/2003 5:38:35 PM EST
Very Nice!
Link Posted: 12/11/2003 5:39:25 PM EST
Hey Guys I used two Mountain Bike Handle bar grips back to back on mine, Its rubber right diameter and they slide on and are tuff. Look good too. cp
Link Posted: 12/11/2003 7:04:44 PM EST
i like it!!
Link Posted: 12/11/2003 7:27:53 PM EST
Just ordered mine yesterday, lots of good ideas to ponder.
Link Posted: 12/12/2003 4:20:26 AM EST
Pics added above
Link Posted: 12/12/2003 6:14:59 AM EST
NICE! Collection
Link Posted: 12/12/2003 9:05:47 AM EST
Originally Posted By eaglecp: Hey Guys I used two Mountain Bike Handle bar grips back to back on mine, Its rubber right diameter and they slide on and are tuff. Look good too. cp
View Quote
I need to see pics of this too! They all look very nice guys.
Link Posted: 12/12/2003 9:21:34 AM EST
I did another variety of the wrap. I'll post a pic tonight.
Link Posted: 12/12/2003 10:42:26 AM EST
When I had an ARFX ( sold it on the EE), I cut the foam sleeve in half and only installed one end on the buffer tube, flat side against the buttpad and the tapered end forward. A different look and clearance for the charge handle.
Link Posted: 12/12/2003 10:57:37 AM EST
Originally Posted By 5subslr5: A suitably colored prophylactic might add a bit of conversational interest to your ACE stock. I believe a 'ribbed' model would help insure a proper cheek weld. (Might be a little slippery though.) 5sub
View Quote
[lol]
Top Top