Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Posted: 10/23/2004 5:17:11 AM EST
[Last Edit: 10/23/2004 5:26:31 AM EST by jcovercash]
First off thanks to the very informative guides and articles from this site I was able to dissaseble my gun and put it back togahter with NO problems. The picture guides made doing this cake :D


My gun is back togahter with the following mods.

YHM Phantom 5C1 FH
G27 Grip W/ the Gapper
Acuwedge
YHM 2 Peice Handguard
Ace Skeleton Stock
(Plus I picked up 1,500 rounds of XM193 Yesterday :p, Should last me a few range trips.)

Now I just have to decide on some optics, and on a two stage trigger (I tried a gun with an RRA 2 stage at a gun show but didn't really like the feel on it, it felt like the stock trigger weight just with 2 stages.) I also need some covers to go over the rails to protect them. Any other items you would suggest I get?


PICTURES



Now I just can't wait to go shoot it tomorrow!
http://www.chromeillusions.net/AR15/IMG_0147.jpg
http://www.chromeillusions.net/AR15/IMG_0148.jpg
http://www.chromeillusions.net/AR15/IMG_0149.jpg


Thanks again everyone for your help.

Josh
Link Posted: 10/23/2004 5:23:49 AM EST
[Last Edit: 10/23/2004 5:26:10 AM EST by TexasGunman]
Look good,also look like you mounted your handguard up side down.


TG
Link Posted: 10/23/2004 5:27:16 AM EST
[Last Edit: 10/23/2004 5:30:46 AM EST by jcovercash]

Originally Posted By TexasGunman:
Look good,also look like you mounted your handguard up side down.hr


Nope Just looked at YHM's instructions and the 3 rail peice is supposed to go up top, and the single rail peice goes on the bottom, so it is correct.
Link Posted: 10/23/2004 5:30:17 AM EST
2ndd picturee looks correct,but the first picture.




TG
Link Posted: 10/23/2004 5:33:13 AM EST

Originally Posted By TexasGunman:
2ndd picturee looks correct,but the first picture.href=www.chromeillusions.net/AR15/IMG_0147.jpg


TGhug.gif



Im not really sure what you are talking about, But I am still learning about these guns so I may not be as prone to notice stuff as others. But it is installed correct though, I checked.
Link Posted: 10/23/2004 5:52:09 AM EST
The three large vent holes belong at the top,like in your 2n pix,the first pix, the three vent holes
are at the bottom.

I have the same handguard on my M4 clone.

TG
Link Posted: 10/23/2004 6:07:06 AM EST

Originally Posted By TexasGunman:
The three large vent holes belong at the top,like in your 2n pix,the first pix, the three vent holes
are at the bottom.

I have the same handguard on my M4 clone.

TG



Those 3 large ventholes are on everyside.
Link Posted: 10/23/2004 7:04:11 AM EST
I don't care if you install it inside out as long as you like it. So the big question is.....have you taken it out and shot it yet, and how do you like it?
Link Posted: 10/23/2004 1:36:45 PM EST

Originally Posted By Stickman:
I don't care if you install it inside out as long as you like it. So the big question is.....have you taken it out and shot it yet, and how do you like it?



No :'(. Couldn't get to the range today had a lot going on. Im heading out there first thing in the morning though :). Hopefully Ill be able to take some pictures while im there. Gonna take my dads .338 Ruger and site it in too. Some of his friends are going along and bringing some of their guns, should be a fun filled day :D


Josh
Top Top