User Panel
Quoted:
Any way to convert these to a 1x? If so where to get parts? View Quote
I've ordered the adapter, but not a lens. The lens is much harder to find, as you want one built for a 1" sensor, with manual focus, and ideally no shutter. These particular lens are commonly used for CCTV cameras, but have become popular with the micro 4/3 camera crowd. You also want a high f stop on the lens. An f1.5 lens is a higher f stop than an f2.0 lens. Ideally you want to stay under f2.0 |
|
Quoted:
Any way to convert these to a 1x? If so where to get parts? View Quote Quoted: The original 1x lenses are no longer available. From what I've read, you can use the adapter listed below with a 25mm c mount lens to achieve 1x magnification. www.amazon.com/dp/B00JEROI5SI've ordered the adapter, but not a lens. The lens is much harder to find, as you want one built for a 1" sensor, with manual focus, and ideally no shutter. These particular lens are commonly used for CCTV cameras, but have become popular with the micro 4/3 camera crowd. You also want a high f stop on the lens. An f1.5 lens is a higher f stop than an f2.0 lens. Ideally you want to stay under f2.0 View Quote https://www.ar15.com/forums/armory/Need_1x_lens_for_ATN_Night_Spirit_2__and_helmet_mount/18-469667/ Basically what Islandtimes said |
|
|
|
Quoted:
I've ordered the adapter, but not a lens. The lens is much harder to find, as you want one built for a 1" sensor, with manual focus, and ideally no shutter. These particular lens are commonly used for CCTV cameras, but have become popular with the micro 4/3 camera crowd. You also want a high f stop on the lens. An f1.5 lens is a higher f stop than an f2.0 lens. Ideally you want to stay under f2.0 View Quote |
|
My 2 units finally arrived. One had a heavily corroded/partially missing battery cap. Swapped the very clean and intact cap from the other unit and TADA!!!! We have light!
Attached File The other units switch was fucked up and this one may have gotten left on when it broke. Attached File I threw a battery and the good cap on this one, no green glow. When I switched to the IR, the IR lit up (I checked it with my phone camera). What would be the next step? Crack it open and look for loose broken stuff? Then put 3 volts to the tube leads? OP, thanks for posting this deal. You helped this Po Boy get into another NV device. |
|
It was sold out before, but I got mine after they "sold out" once before. My piggy banks are tapped out for the Holidays. |
|
Hello all. Since I'm hacking into this thing to learn, I am taking photos. Figured it couldn't hurt to share.
It seems that everything on the inside was intact. No loose/broken connections. Attached File Attached File Attached File Attached File |
|
Some more.
I touched the 2 leads on the tube onto a CR123 battery and got no glow. So I'm assuming this tube is dead, correct? Maybe I'll get my mitts on a different tube that will fit and make this bad boy work. Attached File Attached File Attached File Attached File |
|
Quoted:
Some more. I touched the 2 leads on the tube onto a CR123 battery and got no glow. So I'm assuming this tube is dead, correct? Maybe I'll get my mitts on a different tube that will fit and make this bad boy work. https://www.AR15.Com/media/mediaFiles/399622/KIMG1149_JPG-760447.JPG https://www.AR15.Com/media/mediaFiles/399622/KIMG1150_JPG-760448.JPG https://www.AR15.Com/media/mediaFiles/399622/KIMG1151_JPG-760449.JPG https://www.AR15.Com/media/mediaFiles/399622/KIMG1152_JPG-760450.JPG View Quote |
|
Quoted: Dead unless the leads are fucked at the tube. View Quote There was something like Gorilla glue all over everything, I can get the tube out becuase there is glue all over it. The tab that mates with the groove in the tube is gone. EDIT. Tube is out. Attached File Attached File Attached File |
|
I purchased two different 25mm lenses off of ebay to try out. One is a Computar 25mm f1.4, and the other is a Pentax 25mm f1.4 which looks to have larger lenses than the Computar. The Pentax was scheduled to be delivered today, except not since the mail isn't running today.
Question: I purchased several PVS14 mounts to use with the night spirit, but the mounts all have a small nub on them that interfaces with a PVS14. Should I file the nub off of the mounts, or remove some material from the night spirit so that the nubs fit? |
|
Quoted:
I purchased two different 25mm lenses off of ebay to try out. One is a Computar 25mm f1.4, and the other is a Pentax 25mm f1.4 which looks to have larger lenses than the Computar. The Pentax was scheduled to be delivered today, except not since the mail isn't running today. Question: I purchased several PVS14 mounts to use with the night spirit, but the mounts all have a small nub on them that interfaces with a PVS14. Should I file the nub off of the mounts, or remove some material from the night spirit so that the nubs fit? View Quote I usually modify the part that is cheaper/easier to replace. In this case the PVS14 mount. Let me know which lens works I'd like to get one for my working unit. Should probably get a PVS14 mount too. |
|
Quoted:
I purchased two different 25mm lenses off of ebay to try out. One is a Computar 25mm f1.4, and the other is a Pentax 25mm f1.4 which looks to have larger lenses than the Computar. The Pentax was scheduled to be delivered today, except not since the mail isn't running today. Question: I purchased several PVS14 mounts to use with the night spirit, but the mounts all have a small nub on them that interfaces with a PVS14. Should I file the nub off of the mounts, or remove some material from the night spirit so that the nubs fit? View Quote |
|
Quoted:
@Islandtimes I usually modify the part that is cheaper/easier to replace. In this case the PVS14 mount. Let me know which lens works I'd like to get one for my working unit. Should probably get a PVS14 mount too. View Quote View All Quotes View All Quotes Quoted:
Quoted:
I purchased two different 25mm lenses off of ebay to try out. One is a Computar 25mm f1.4, and the other is a Pentax 25mm f1.4 which looks to have larger lenses than the Computar. The Pentax was scheduled to be delivered today, except not since the mail isn't running today. Question: I purchased several PVS14 mounts to use with the night spirit, but the mounts all have a small nub on them that interfaces with a PVS14. Should I file the nub off of the mounts, or remove some material from the night spirit so that the nubs fit? I usually modify the part that is cheaper/easier to replace. In this case the PVS14 mount. Let me know which lens works I'd like to get one for my working unit. Should probably get a PVS14 mount too. Attached File Attached File Attached File Attached File |
|
Quoted:
It's waay to heavy to be doing this conversion. But post pics! View Quote View All Quotes View All Quotes Quoted:
Quoted:
I purchased two different 25mm lenses off of ebay to try out. One is a Computar 25mm f1.4, and the other is a Pentax 25mm f1.4 which looks to have larger lenses than the Computar. The Pentax was scheduled to be delivered today, except not since the mail isn't running today. Question: I purchased several PVS14 mounts to use with the night spirit, but the mounts all have a small nub on them that interfaces with a PVS14. Should I file the nub off of the mounts, or remove some material from the night spirit so that the nubs fit? NS2 w/ 3x lens - 22.9 oz 3x lens - 10.1 oz NS2 w/ 1x lens - 15.5 oz So yeah, it's a little heavy, but doesn't seem too bad considering. I don't yet have a helmet or crye nightcap to try it with. This lens does have a shutter, so if you removed that you'd lose a little more weight. |
|
Quoted: As far as weight: NS2 w/ 3x lens - 22.9 oz 3x lens - 10.1 oz NS2 w/ 1x lens - 15.5 oz So yeah, it's a little heavy, but doesn't seem too bad considering. I don't yet have a helmet or crye nightcap to try it with. This lens does have a shutter, so if you removed that you'd lose a little more weight. View Quote Is this the right lens? @IslandTimes https://www.ebay.com/itm/Cosmicar-Pentax-25mm-1-1-4-f1-4-C-Mount-Lens-CCTV-M4-3-Q-Digital-Cameras/153205900776?hash=item23abc885e8:g:CoQAAOSw6EZbtjZA |
|
Quoted:
Awesome man! I'll have to pic up one of those lenses. That image looks great. It's also a huge weight reduction. I have a couple different mount ideas. Is this the right lens? @IslandTimes https://www.ebay.com/itm/Cosmicar-Pentax-25mm-1-1-4-f1-4-C-Mount-Lens-CCTV-M4-3-Q-Digital-Cameras/153205900776?hash=item23abc885e8:g:CoQAAOSw6EZbtjZA View Quote View All Quotes View All Quotes Quoted:
Quoted: As far as weight: NS2 w/ 3x lens - 22.9 oz 3x lens - 10.1 oz NS2 w/ 1x lens - 15.5 oz So yeah, it's a little heavy, but doesn't seem too bad considering. I don't yet have a helmet or crye nightcap to try it with. This lens does have a shutter, so if you removed that you'd lose a little more weight. Is this the right lens? @IslandTimes https://www.ebay.com/itm/Cosmicar-Pentax-25mm-1-1-4-f1-4-C-Mount-Lens-CCTV-M4-3-Q-Digital-Cameras/153205900776?hash=item23abc885e8:g:CoQAAOSw6EZbtjZA |
|
That's actually really fucking cool dude, nice work! The 10130 project ever take off?
|
|
I have one to spare if someone wants to PM me.
It is totally dead in regard to the tube. I will sell it for exactly what it cost me. |
|
So the mounts don't quite line up, but this works okay. I don't have anywhere to actually shoot it like this, but I don't think it would be horrible. A non cantilever mount for the aimpoint might actually work better.
Attached File Attached File Attached File The bottom picture is with the IR weapon light on. Really hard to get a good picture. The images were actually very crisp. |
|
|
|
The Computar 25mm f1.4 lens came in and I was able to try it out. While the lens is shorter than the Pentax lens, the field of view seems to be the same, with a negative being that it is a heavier lens.
Side by side the picture did seem dimmer through the Computar lens, but that may have just been the tube. |
|
|
|
Well I took advantage of the 15% off eBay coupon and ordered a ZenitCo Perst-1 IR desgnator. For the price it seems like it would be pretty decent, but we'll see.
|
|
Quoted:
Well I took advantage of the 15% off eBay coupon and ordered a ZenitCo Perst-1 IR desgnator. For the price it seems like it would be pretty decent, but we'll see. View Quote I have a Christmas bonus coming. I’d prefer to sell/trade a couple NVG decvices and buy Duals, but if I can’t find what I want... |
|
|
Quoted:
Rough price? I have a Christmas bonus coming. I’d prefer to sell/trade a couple NVG decvices and buy Duals, but if I can’t find what I want... View Quote View All Quotes View All Quotes Quoted:
Quoted:
Well I took advantage of the 15% off eBay coupon and ordered a ZenitCo Perst-1 IR desgnator. For the price it seems like it would be pretty decent, but we'll see. I have a Christmas bonus coming. I’d prefer to sell/trade a couple NVG decvices and buy Duals, but if I can’t find what I want... There's not a lot of info about it out there. If it doesn't hold zero under recoil or isn't suited for longer range, I have a 22LR AR that it should do fine on. |
|
Quoted:
Ended up being $133 shipped. There was another pro code for $10 for using a Mastercard, but I couldn't get that one to work. There's not a lot of info about it out there. If it doesn't hold zero under recoil or isn't suited for longer range, I have a 22LR AR that it should do fine on. View Quote View All Quotes View All Quotes Quoted:
Quoted:
Quoted:
Well I took advantage of the 15% off eBay coupon and ordered a ZenitCo Perst-1 IR desgnator. For the price it seems like it would be pretty decent, but we'll see. I have a Christmas bonus coming. I’d prefer to sell/trade a couple NVG decvices and buy Duals, but if I can’t find what I want... There's not a lot of info about it out there. If it doesn't hold zero under recoil or isn't suited for longer range, I have a 22LR AR that it should do fine on. If it doesn’t hold zero on an AR, I’ll put it on my MP5. |
|
Quoted: Ended up being $133 shipped. There was another pro code for $10 for using a Mastercard, but I couldn't get that one to work. There's not a lot of info about it out there. If it doesn't hold zero under recoil or isn't suited for longer range, I have a 22LR AR that it should do fine on. View Quote Quoted:
That’s sort of how I’m thinking.... If it doesn’t hold zero on an AR, I’ll put it on my MP5. View Quote |
|
Quoted:
Photonis makes discount 10130's. View Quote Quoted:
What's the going price for a Photonis versus surplus or other sourced ones?? View Quote I'd like to know as well. |
|
They had goggles a minute ago...
https://www.apexgunparts.com/more/surplus.html/night-vision-atn-nvg-7-gen-2-dual-eye-relief-innop-asis.html I got 2 before they went out of stock. |
|
Quoted:
They had goggles a minute ago... https://www.apexgunparts.com/more/surplus.html/night-vision-atn-nvg-7-gen-2-dual-eye-relief-innop-asis.html I got 2 before they went out of stock. View Quote |
|
Quoted:
Damn. I even browsed and searched their site this morning and those weren't listed. They must have put them up this afternoon. View Quote View All Quotes View All Quotes Quoted:
Quoted:
They had goggles a minute ago... https://www.apexgunparts.com/more/surplus.html/night-vision-atn-nvg-7-gen-2-dual-eye-relief-innop-asis.html I got 2 before they went out of stock. |
|
So the factory in China that makes these doesn't know if they still have spare parts laying around because they haven't made them in a long time. Russian contact says Katod isn't selling tubes ("Katod is VERY highly regulated by the state now. All components of modern NV devices are banned for export. Only gen 1 and 1+ are allowed.") but Ekran is but the price for a new one is 600-3k depending on the specs (private chat with two different chinese manufacturers) and that's without a mark up from what they pay according to them. Photonis has the XX0041C's they are something like 60% the price of an echo according to a very knowledgeable source.
I asked Glynn about hooking it the fuck up with them since he's like the NA go to guy for Photonis shit but he said he'd have to order a lot at once to get it done. TNVC has Russian contacts and tubes in their other line so they could step in to clarify. The chinese manufacturer did offer to repair any unit but not for any reasonable cost I'd assume, plus shipping is atrocious back and forth. The only way to get a hold of the Chinese manufacturer is to know them and use the Chinese messaging app because otherwise they aren't very friendly. If you want to send your unit in, I'd suspect it would be more than a new unit costs on Amazon. The parts themselves are or are not available because he sucks at english and I can't understand half the shit he types, but he's cool as fuck anyway. Sorry, been sick and Tyler at UNV sent me a whole fucking RQE bridge, clip set, skull spoon and a texas lasered pmag for free because he's awesome. I'll post some pics of it using dual mums later this week, I want to do him some justice for basically shipping $1k worth of shit on his dime for nothing more than me writing an email back in June. He's cool. Also, TNVC needs to unban you know who asap. He was an asset to us here and this is the last active NVG forum on the net. We need every person in this hobby to be able to share as much information as possible because this is all going to be a lost art soon (L3 already proved they just randomly push buttons to produce a shitty wildly variable product. Thanks L3, you fucking cucks) and without an archive our grandchildren may never know the full story behind these, like vacuum tubes are to this generation. |
|
I picked one up last week and have a half ass dead tube. Itll create a picture however is very noisy and only seems to pick up headlights, light from windows, etc. You could see outdoors without it better than with haha
Took it apart today and Im getting ~2.5-3v to the tube via the board so that should be fine. No loose connections inside unless they are at the tube itself. Im guessing it was powered up during the day and burnt out. Any way back from this or to improve performance? Anyone have one with a good tube that the housing is destroyed they would want to part with? My housing is about perfect with the eye cup and lens cap. Anyone have a source for surplus tubes? Wouldnt mind taking a crack at throwing another tube at it somehow... |
|
Quoted:
I picked one up last week and have a half ass dead tube. Itll create a picture however is very noisy and only seems to pick up headlights, light from windows, etc. You could see outdoors without it better than with haha Took it apart today and Im getting ~2.5-3v to the tube via the board so that should be fine. No loose connections inside unless they are at the tube itself. Im guessing it was powered up during the day and burnt out. Any way back from this or to improve performance? Anyone have one with a good tube that the housing is destroyed they would want to part with? My housing is about perfect with the eye cup and lens cap. Anyone have a source for surplus tubes? Wouldnt mind taking a crack at throwing another tube at it somehow... View Quote |
|
|
|
I have an extra one of these that I don't need.
Tube is dead, and the ir light doesn't come on. Optics are good. has euecup and cap |
|
Quoted: The original 1x lenses are no longer available. From what I've read, you can use the adapter listed below with a 25mm c mount lens to achieve 1x magnification. www.amazon.com/dp/B00JEROI5SI've ordered the adapter, but not a lens. The lens is much harder to find, as you want one built for a 1" sensor, with manual focus, and ideally no shutter. These particular lens are commonly used for CCTV cameras, but have become popular with the micro 4/3 camera crowd. You also want a high f stop on the lens. An f1.5 lens is a higher f stop than an f2.0 lens. Ideally you want to stay under f2.0 View Quote I think I only need one, and maybe an extra. If anyone needs one, PM and you can have one for the cost of shipping. |
|
Hey apex ns2 tinkerers.
Been watching this thread for awhile. I got a Q thats a bit off topic. I have a NS2 that i have had for years. Tube burned out some years back. I recently sent it to ATN to have it swapped out for a fresh tube. Old tube was a epm223. new tube is a epm66g-4k. New tube works in starlight or with the ir illum. but exhibits alot of sparkle in very low light (indoors), also has squirm so bad in the lower light with out ir that the image looks like a moving jackson pollock painting. For those of you with working tubes, how are they performing inside at night with no ir illum? Clear to dark, or same as mine? |
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.