Armory Sponsor
[ARCHIVED THREAD] - Ever wonder what a double powder load of 9mm will do to a micro Dagger? (Page 3 of 3)
|
Quoted: I have seen similar KABOOMS at 2 different USPSA matches. Both times, it was the same R.O., both times, he asked "Dillon 550 ?" Both times the shooter said "yes" Thanks again to OP. This was a good thread. While I've always had a personal bias for autoindexing - this post right here has to be the most powerful one in the whole thread. Not saying it can't safely be done - but wow. I will say for rifle - or really any situation where a double means an inescapable volume of dumped powder, then less critical. But for pistol chunk chunk chunk... |
|
Quoted: No offense intended to anyone here, or anyone that reloads, but this is why I never allow reloads to be fired in any gun I own. And before all the "factory loads have caused KABOOMs, too" comments, the odds don't even come close to comparing to the ones caused by reloads. This is the Reloading Forum, we reload here. |
|
I'm going to comment on my observation of the video. Everything else has been mentioned. When firing rounds 1 through 7, I believe I see muzzle flash, #5 is iffy due to the speed of 4,5,6. I don't see any flash for round 8, and kaboom at round 9. Back to the barrel obstruction comment earlier? I don't know. Maybe replay in slow motion? Just my thoughts. |
|
Quoted: Some of the things I love about the XL650 / 750 is that is auto-indexes the case to the nest station, and you have an extra station for the power check buzzer too much, or too little powder will sound the alarm  https://www.youtube.com/watch?v=JXbrTVEI0Cs |
|
Quoted: Actually pretty impressed with how the gun handled that. I have been looking at PSA pistols lately, might pull the trigger on one yet. Kind of my thought. Failure mode isn't about minimizing damage, it's about minimizing harm. So while it looks spectacular, the barrel failed in a manner that resulting in no harm to the shooter. I can't say for sure, but it almost looks like they went for a "soft" alloy in the barrel, as part of that. Recall: "hard" is another word for brittle, and if that barrel was harder, that failure world have been frag of flying metal. Vs holding together but peeling. That may be just an aspect of other manufacturing decisions, but I think OP will agree, that gun failing like a hand grenade with frag, wouldn't have been good. |
|
Quoted: Actually pretty impressed with how the gun handled that. I have been looking at PSA pistols lately, might pull the trigger on one yet. I won’t hesitate to buy another one. That’s part of the pain, the Micro Dagger was basically brand new. It was my second trip to the range with it. I normally carry a G19, the micro dagger with the 15 round magazine is a game changer. |
|
Quoted: I won’t hesitate to buy another one. That’s part of the pain, the Micro Dagger was basically brand new. It was my second trip to the range with it. I normally carry a G19, the micro dagger with the 15 round magazine is a game changer. Quoted: Quoted: Actually pretty impressed with how the gun handled that. I have been looking at PSA pistols lately, might pull the trigger on one yet. I won’t hesitate to buy another one. That’s part of the pain, the Micro Dagger was basically brand new. It was my second trip to the range with it. I normally carry a G19, the micro dagger with the 15 round magazine is a game changer. For perspective - the entire gun is cheaper than your co-pay to the Urgent Care center. |
|
1- Answers one question regarding wet vs dry cleaning. It is a lot easier to see inside brass that is clean metal vs black soot. That requires reloading in 2 stages and is my SOP now for rifle and pistol. For pistol I size and decap on one pass, wet clean brass then dry, finally load it after sorting by headstamp. Resolves brass-related issues which cause most hang-ups, minimizing the chance of a screw-up when dumping powder and seating bullets. 2- Auto indexing does help prevent double charges but.... 3- I still remove all brass from all stations after clearing a problem. I throw removed brass into a cigar box, then process them separately after completing the remainder of the batch. And I use Dillon powder check dies on the 1050s. Glad to see you weren't hurt. |
|
Quoted: 1- Answers one question regarding wet vs dry cleaning. It is a lot easier to see inside brass that is clean metal vs black soot. That requires reloading in 2 stages and is my SOP now for rifle and pistol. For pistol I size and decap on one pass, wet clean brass then dry, finally load it after sorting by headstamp. Resolves brass-related issues which cause most hang-ups, minimizing the chance of a screw-up when dumping powder and seating bullets. 2- Auto indexing does help prevent double charges but.... 3- I still remove all brass from all stations after clearing a problem. I throw removed brass into a cigar box, then process them separately after completing the remainder of the batch. And I use Dillon powder check dies on the 1050s. Glad to see you weren't hurt. I agree. Especially thr first point. Though I just wet tumble pistol brass raw and call it done. This is where media makes a big difference- because that scours the inside to sunglasses-required bright BLING level - for exactly this benefit. Makes it a lot easier to spot the *very* rare Squib-inbound, as it rotates around to the seating station and brightly says Hello! |
|
Quoted: Valid point. I thought it was the KABOOM forum. It seems we're both right. Quoted: Quoted: No offence taken, but you are in the wrong forum posting your viewpoint. This is the Reloading Forum, we reload here. Valid point. I thought it was the KABOOM forum. It seems we're both right. You don't belong here. OP, thank you for sharing this. Best pic of this kind of incident I think I've ever seen. I like the way you've handled it. 4.2gr TG w/ 124gr bullets is my go-to for 9mm. That under 124gr V-Crowns is what's in my sidearm as we speak. Been using it for years, like it alot, for .40 as well. Lot of great advice in this thread. Yeah, I too have a light that shines down on the press, and look in every case. Turret press here, it auto-indexes obviously. |
|
Quoted: Get the light from Inline Fab, it may help, I have it on my 550s and are fantastic. Also, consider working with a slower powder that will fill your cases. I'm sure you know this but, If you ever leave your press for any reason leave it with the handle in the down position. This is a good idea. I like to use powders that will overflow the case if there's a double charge, makes it hard to ignore when it happens. |
[ARCHIVED THREAD] - Ever wonder what a double powder load of 9mm will do to a micro Dagger? (Page 3 of 3)
Armory Sponsor