Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
Armory Sponsor
9/20/2012 11:58:27 PM EDT
I just got a Kimber pro carry 2, I'm going to load some 45 rounds
I need some help for bullets I would like to keep the recoil down some
So I was thinking about going with a 200 gn.
Any feedback would be great. Also I need a good site to order them form
Just target shooting. Thanks
9/21/2012 4:49:19 AM EDT
[#1]
45 acp




5.0 grains   W 231
9/21/2012 5:37:05 AM EDT
[#2]
I mostly shoot 200 grain lead SWC's with 3.8 to 4.2 grains of Bullseye.  My standard 1911 will cycle with 3.5 grains.

This is pretty much an old standard load for 1911's.  Nice to shoot, and accurate.  I wouldn't hesitate to ventilate a low life with it, either.

9/21/2012 7:21:12 AM EDT
[#3]
I shoot targets with 185 swc from Barrys with 5.7 of w231 it is accurate and won't beat you up also I like 200gr lswc  but too smokey for indoor range
both are shot thru SA range officer and SA mil spec with 5 in barrels
9/21/2012 10:52:54 AM EDT
[#4]
200gr Hornady XTP, 5.0gr Unique, 16lb recoil spring

This is very soft shooting from my 1911
9/22/2012 6:54:23 AM EDT
[#5]
I got by far the best prices from this guy:       [email protected]    send him an email and see what he is now doing.  I have not bought anything for a couple of years, stocking up at the beginning of the previous lead crisis.
9/22/2012 7:24:27 AM EDT
[#6]
Try all three standard weights - 185, 200 and 230 grainers.  Old John intended for the M1911 to shoot 200 grainers, but the US Army insisted on 230 grains for more stopping power.  Most M1911s, esp the short barreled ones, do better with lighter bullets.  Some believe its best to get the bullet out of the gun asap, before the slide has moved very far. - CW
9/22/2012 11:40:28 AM EDT
[#7]
Quoted:
Try all three standard weights - 185, 200 and 230 grainers.  Old John intended for the M1911 to shoot 200 grainers, but the US Army insisted on 230 grains for more stopping power.  Most M1911s, esp the short barreled ones, do better with lighter bullets.  Some believe its best to get the bullet out of the gun asap, before the slide has moved very far. - CW


good advice
9/22/2012 1:17:43 PM EDT
[#8]
I use 230 grain double struck copper plated Berry's Bullets with max load of Win 231. What recoil???????



185 grain SWC was always a fun load, as hot as possible.  Not much recoil. Your Kimber should feed it fine, mine do.
9/22/2012 5:56:49 PM EDT
[#9]
I've run three different Kimbers.  A stainless Gold Match, a Compact CDP and a TLE.

The Gold Match and the TLE feed and fire anything.  The CDP seems to have a slightly tighter chamber.  It feeds everything, but it does not like to chamber lead SWC (200 grn).  On closer examination there are th occasional rounds that have a tiny bit of extruded bullet lube at the case mouth.  This can sometimes prevent the slide from fully returning to battery.  I switched to plated instead of hard cast, and everything is 100%.  I use unique under 200 flat points.

9/23/2012 4:21:50 PM EDT
[#10]
200 swc H+G 68 WST powder, you'll never look back.
9/23/2012 6:12:41 PM EDT
[#11]
I buy cast 200 gr H&G 68 SWC. I used to use about 5 gr of Win 231, AA#2, or Bullseye. Now I use about 4.8 gr Bullseye. All function well with the standard 16# spring in Gov't models and the standard spring in a Commander. Recoil is noticeably less than standard ball ammo. It's a good practice load, and cheap to do; accurate as well.
Armory Sponsor