Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
Armory Sponsor
12/4/2008 1:43:28 PM EDT
I am considering getting into reloading and am about to buy a significant amount of Speer Gold Dot Ammo. It comes in Nickel casings and before I pull the trigger I just wanted to know ARE THESE CASINGS RELOADABLE??? Considering the new administration about to take office I just wanted to check.

Thanks for all the help, it is greatly appreciated
12/4/2008 2:11:14 PM EDT
[#1]
GTG sometimes a little more effort to size.
12/4/2008 2:30:44 PM EDT
[#2]
Absolutely. I've reloaded plenty of them.
12/4/2008 2:34:58 PM EDT
[#3]
They say the nickle cases may split a little more often than plain brass cases, but they are reloadable.
12/4/2008 2:42:34 PM EDT
[#4]
Never had any problem with nickel cases but I load 45 ACP, not 40.
12/4/2008 3:12:58 PM EDT
[#5]
Yes they are good to reload.
12/4/2008 3:16:06 PM EDT
[#6]
Quoted:
They say the nickle cases may split a little more often than plain brass cases, but they are reloadable.


That's been my experience with .40S&W (loaded hot). These were range pickups and the only ones that DID split were (Speer, IIRC) nickles.

12/4/2008 4:58:12 PM EDT
[#7]
Quoted:
They say the nickle cases may split a little more often than plain brass cases, but they are reloadable.


I don't know why this would be, but 357 nickled cases seem to split at the neck somewhat more often than plain brass.  I don't think you will seen enough difference to be a problem.
12/4/2008 4:59:57 PM EDT
[#8]
Use carbide sizing die.  No lube necessary.
12/4/2008 6:11:04 PM EDT
[#9]
I've heard the nickle might flake off after firing or during resizing.  This is just something I've heard.  You could just buy winchester or remmington umc ammo and use that brass.  It's cheaper I think.  It's not really nice ammo but I kill paper with it so it's good enough for me.
12/4/2008 6:41:43 PM EDT
[#10]
I've reloaded .40 S&W for about 4 years.  Most of my 1000+ .40 S&W cases are brass, but of the several dozen nickel cases scattered through my supply, I've yet to see one split, or the nickel plating flake off.  Most of them have been reloaded at least 4 times, occasionally with rather hot loads.


I think the "splitting/nickel flaking off" stuff is just one of those things you hear, at least for .40 S&W.  Speer ammo is good stuff, so you'll be fine.  Buying & shooting factory ammo is great way to get a brass supply.  So is buying new brass directly from Starline.

What kind of gun are you reloading for?  If it's a Glock, there are some special considerations.
12/5/2008 7:31:21 AM EDT
[#11]
Quoted:


What kind of gun are you reloading for?  If it's a Glock, there are some special considerations.


Uh oh.   What kind of special considerations?

12/5/2008 7:38:46 AM EDT
[#12]
Look at the "reloading for glocks" thread in this forum.
12/5/2008 2:18:41 PM EDT
[#13]
I have reloaded lots of nickle cases in .40 and other calibers.  I have seen no more failures in them the plain brass.

I have some old 357 that has been through the tumbler so many times the nickel is wearing off in spots.
12/5/2008 3:02:39 PM EDT
[#14]
From what I understand, the nickel plating is more brittle than plain brass.  This is what causes the split.

skink
Armory Sponsor