[ARCHIVED THREAD] - AMD-65 Part Kits

**Posted: 5/3/2007 11:19:20 AM EDT**

Quoted:
I just ordered two of the copes AMD-65 kits!

What is the suggested flat for doing this build? Will a basic Tapco do the job?

THX!

yeah I got a few myself!
You can use just a basic AK builder, Tapco, etc and make a "notch" cut into the left rear of the receiver. See the picture of the NDS-65 on their website and you will see what I mean...it's the same as the NDS-3 with the notch cut out

**Posted: 5/3/2007 11:57:28 AM EDT**

I usually get the Tapco's with he Trunnon holes pre drilled, does any one know if those work?

Thx

**Posted: 5/3/2007 1:21:36 PM EDT**

Quoted:
I usually get the Tapco's with he Trunnon holes pre drilled, does any one know if those work?

Thx

I don't think it will work as the rear rivet holes are different for the amd
take a look at the rear trunion holes

"Regular" Romanian/Hungarian pre-drilled (this is what the Tapco flat ends up looking like)

AMD

**Posted: 5/3/2007 1:23:49 PM EDT**

I built one with a standard receiver.

The notch in the back is easy to cut.

I filled the extra hole on the left side of the receiver with a sling swivel.

Not so bad, but for my next few AMD builds I got a couple of NoDak receivers.

**Posted: 5/3/2007 1:32:48 PM EDT**

Quoted:

Quoted:
I usually get the Tapco's with he Trunnon holes pre drilled, does any one know if those work?

Thx

I don't think it will work as the rear rivet holes are different for the amd
take a look at the rear trunion holes

"Regular" Romanian/Hungarian pre-drilled (this is what the Tapco flat ends up looking like)
www.nodakspud.com/images/NDS-3web.jpg
AMD
www.nodakspud.com/images/NDS65-1web.jpg

Yep your right! I just haven't tried it w/o the holes yet, better buy an extra flat!

**Posted: 5/3/2007 1:33:21 PM EDT**

Quoted:

Quoted:
I usually get the Tapco's with he Trunnon holes pre drilled, does any one know if those work?

Thx

I don't think it will work as the rear rivet holes are different for the amd
take a look at the rear trunion holes

"Regular" Romanian/Hungarian pre-drilled (this is what the Tapco flat ends up looking like)
www.nodakspud.com/images/NDS-3web.jpg
AMD
www.nodakspud.com/images/NDS65-1web.jpg

Yep your right! I just haven't tried it w/o the holes yet, better buy an extra flat!

**Posted: 5/4/2007 12:47:49 PM EDT**

copes AMD-65 kits where and how much? I did not see them on the website.

**Posted: 5/4/2007 2:15:51 PM EDT**

Copes has a preorder special going. The kits will not be available for at least 8 wks, just like the current AMMS feeding frenzy.

**Posted: 5/4/2007 3:20:22 PM EDT**

Not trying to have them all sold before I get one, but have you seen they have Yugo underfolders for an excellent price as well?

**Posted: 5/4/2007 5:17:32 PM EDT**

Those are milled kits not stamped

**Posted: 5/4/2007 6:26:01 PM EDT**

Quoted:
Those are milled kits not stamped

um, no. the copes dist amd65 kits are stamped kits. akforum members got an email about the deal.

**Posted: 5/4/2007 7:17:58 PM EDT**

I think that Beemerman was referring to the Yugo UF kits being milled instead of stamped receivers, not the AMD-65's

**Posted: 5/5/2007 3:40:43 AM EDT**

Quoted:

Quoted:
Those are milled kits not stamped

um, no. the copes dist amd65 kits are stamped kits. akforum members got an email about the deal.

the yugo kits that were referred to in the posts above are milled

**Posted: 5/5/2007 9:26:52 AM EDT**

Copes AMD-65 preorder

AK forum thread

Warning

Confirm Action

[ARCHIVED THREAD] - AMD-65 Part Kits

[ARCHIVED THREAD] - AMD-65 Part Kits