Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
AR Sponsor
Previous Page
/ 220
Next Page
3/20/2007 9:05:24 AM EDT
[#1]
ALL BEAUTIFUL SETUPS !!

Being "virgin" to the board, would someone share what the letters RECCE stand for?

Thanks in advance....
You can't win the Kentucky Derby with a jackass ! ! !
As soon as I'm finished, I'll be through.....
3/20/2007 9:18:36 AM EDT
[#2]

Originally Posted By 1962guy:
ALL BEAUTIFUL SETUPS !!

Being "virgin" to the board, would someone share what the letters RECCE stand for?

Thanks in advance....


It's just short for reconnaissance.
3/20/2007 9:35:34 AM EDT
[#3]
Hokie – Thanks for the explanation, that all makes perfect sense. As you note, each situation is different. Each person needs to evaluate their own needs and intended use and then setup their weapon accordingly. Sounds like you nailed it for your purpose.

(and that 5.56MM TAP is some sweet ammo too! Nice trade. I should have bought more of it when I had the chance )

1962guy - RECCE is slang for Reconnaissance. Basically just another way to refer to a “recon” rifle.
Disclaimer:
My comments above are worth what you paid for them.
My posts often contain poor grammar and spelling and may be edited.
There is no telling what state of mind I was in when I wrote this or even if I had a state of mind at the
3/20/2007 9:41:09 AM EDT
[#4]
my take on it.  Was hitting 8x8 targets out to 300yds with black hills blue box 52gr all day......(also wears a new ctr stock on it now rather than the clanky ass m4


3/20/2007 9:55:48 AM EDT
[#5]
I've been tweaking this setup for a while now. I just mounted the TA33 and she is pretty much done.

RRA lower w/ 2 stage trigger
Magpul CTR stock, trigger guard, MIAD grip
Vltor receiver ext.
Vltor sling plate

Vltor MUR upper rec.
Noveske 16" Recon bbl
DD 9.0 Lite rail
Vltor gas block
Smith Vortex FH
Troy BUIS
Trijicon TA33R8 w/ Larue mount
Young Manuf. bolt carrier



3/20/2007 9:59:04 AM EDT
[#6]
Had this one for awhile now and am tweaking the configuration slightly... considering going from a single-point to a VCAS and adding a can:

Обезьяны всех стран, соединитесь!
3/20/2007 10:03:19 AM EDT
[#7]

Originally Posted By mtdawg169:
I've been tweaking this setup for a while now. I just mounted the TA33 and she is pretty much done.

RRA lower w/ 2 stage trigger
Magpul CTR stock, trigger guard, MIAD grip
Vltor receiver ext.
Vltor sling plate

Vltor MUR upper rec.
Noveske 16" Recon bbl
DD 9.0 Lite rail
Vltor gas block
Smith Vortex FH
Troy BUIS
Trijicon TA33R8 w/ Larue mount
Young Manuf. bolt carrier

i75.photobucket.com/albums/i287/mtdawg169/100_0604.jpg

i75.photobucket.com/albums/i287/mtdawg169/100_0603.jpg


you didnt even take a picture with the door open to show off your sweet chrome carrier?
sweet rig
3/20/2007 10:23:00 AM EDT
[#8]
Noveske Recon with 13.2 LaRue



Builder of fine parts guns since 1997.

كافر

3/20/2007 11:01:40 AM EDT
[#9]

Originally Posted By stretch415:
you didnt even take a picture with the door open to show off your sweet chrome carrier?
sweet rig


Thanks!

I realized that as I was typing up the parts list It's in there though! I'm not much on posing the pictures. That one is just laying on my garage floor. Heck, I'm lucky my feet aren't in the pic.
3/20/2007 11:29:20 AM EDT
[#11]
Yup, mine was built for precision.

Duh.

3/20/2007 11:35:35 AM EDT
[#12]

Originally Posted By knightsar:
My version of a Reece


img70.imageshack.us/img70/9642/dsc00816largeks5.jpg



STILL one of my favorite Recces on this board.
Would John Wayne be having this conversation?


Originally Posted By steve-oh:
My AR10 is still having a few minor problems. So I would probably pawn it off on someone in a SHTF situation.
3/20/2007 12:22:38 PM EDT
[#13]
Very nice rifles guys... Thanks for posting.
3/20/2007 1:10:20 PM EDT
[#14]
One of these day Ill build one, but just an upper will run you 7-900, then add optics, 300 and up and EXPENSIVE
There's a storm coming...

ΜOΛΩΝ ΛΑΒΕ
3/20/2007 1:19:41 PM EDT
[#15]

Originally Posted By cgv69:

Originally Posted By Saryan:
I only have a couple pics as mine is still in the build up phases. The important stuff is here though.
Lilja Dev Group SPR profile barrel
13.2 Larue on the way to replace 9.0
Young Mfg BC
PRI gasbuster
Larue SPR mount
Knights 2 stage on the way to replace CMK
OPS Inc MB and 12th model in near future.
My scope will be the 2-10 NF
I am also trying to get my hands on either a Colt M4 upper or a Larue Stealth. Cant decide which route yet. I havnt had a real "photoshoot" for it yet so the pics are crappy but they are pics.

img.photobucket.com/albums/v314/saryan25/IMG_1858.jpg
img.photobucket.com/albums/v314/saryan25/100_1328.jpg
img.photobucket.com/albums/v314/saryan25/100_1330.jpg

Your's sounds like it will end up very similar to the way I hope my (which I am still working on) will end up.

As far as the upper, If you want a Colt M4 receiver and have a C&R license, you can get one from Brownells for about $165. Only problem is the last one I got looked pretty rough. Not a huge deal but if you are interested in another option, DD is making uppers now. They are still milled from forged blanks but I'm thinking (hoping) the QC is a little better then your average CMT upper. Rainier Arms has them for $150 with or without M4 ramps...
www.rainierarms.com/img/shop/product/fb61746c141884f3eb41c0fd9bbe86d9.jpg


A friend of mine with access to the TDP confirms that DD uppers are within the TDP, and CMTs are not always so...
"There is no right reason constituted by nature." Thomas Hobbes, Leviathan, 1651
3/20/2007 10:27:08 PM EDT
[#16]

Originally Posted By Hokie:

Originally Posted By TurnTwo:
Bump

Anymore recent Recce builds?  


re-configured Recce builds count?

img.photobucket.com/albums/v734/Hokie1850/Midlength11b-da.jpg


Damn skippy they count... VERY NICE!
3/20/2007 10:33:11 PM EDT
[#17]
LaRue Tactical Supporter, Former Air Assault Guy & SOPMOD Poster Child.
3/20/2007 10:34:28 PM EDT
[#18]
LaRue Tactical Supporter, Former Air Assault Guy & SOPMOD Poster Child.
3/21/2007 9:14:39 AM EDT
[#19]
Damn thats some fine photography -- I am always humbled by your pictures.



I've posted this one before-- but I made some additions after leave so...






Good, Bad... I'm the guy with the Gun

Without the neccessary toughness to apply training in adverse situations, the training is valueless
3/21/2007 1:38:12 PM EDT
[#20]

Originally Posted By mfingar:
i2.photobucket.com/albums/y44/mfingar/recce_c.jpg


Very nice weapon Sir.
Infantry, Because anything else is just support.

TANT QUE JE PUIS
3/21/2007 1:44:04 PM EDT
[#21]
I know....I briefly considered sending my gun to him for some professional photos...

but then realized my wife would NEVER go for it.
"Do you see any similarities here, sir? How long before gun control proponents realize that your .223 and my 5.56mm make the exact same sized hole? "
-richardh247
3/21/2007 2:26:41 PM EDT
[#22]
My Recce

Thought I'd posted that already.
"What do you want to do now, Captain?"
"What we always do. Fight 'em until we can't.", CPT Kara Thrace
3/21/2007 5:45:08 PM EDT
[#23]

Originally Posted By KevinB:
Damn thats some fine photography -- I am always humbled by your pictures.



I've posted this one before-- but I made some additions after leave so...


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq002a.jpg


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq006a.jpg


I love a rifle that's PURE function...  I would have to say that is my favorite rifle I've seen on the board...  Hose clamps for light mounts... PRICELESS!  

A++ my friend!

You get 3 out of 3 headbanger dudes...


PS - The Short Dot is the icing  
3/21/2007 5:53:57 PM EDT
[#24]

Originally Posted By KevinB:
Damn thats some fine photography -- I am always humbled by your pictures.



I've posted this one before-- but I made some additions after leave so...


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq002a.jpg


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq006a.jpg


big +1 that is a sweet rifle
3/21/2007 8:03:46 PM EDT
[#25]

Originally Posted By KevinB:
Damn thats some fine photography -- I am always humbled by your pictures.



I've posted this one before-- but I made some additions after leave so...


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq002a.jpg


img.photobucket.com/albums/v193/EvilKev/Iraq/Recce-Iraq006a.jpg


Very nice.  I never get tired of you posting pictures of that rifle.  Keep them coming.
3/24/2007 2:35:25 AM EDT
[#26]
6.8SPC 16" midlength, LT 12.0. Very handy, shoots where you point it.

3/24/2007 4:27:01 AM EDT
[Last Edit: ReadinessHub][Edited] [#27]
I wish I had some of those rigs when I was in doing Recce Routes.

When I was in the USAF on Recce routes, we just had M4A1's and the only optics they gave us were binocs...

Though the USAF definition of Recce is to gather information only... only fighting when fired upon and to preserve life and gain a route to safely break contact.
3/24/2007 8:41:03 PM EDT
[#28]
Guys all these Recces are so nice,but i have a question..are these rifles used in combat.?.i am wanting to build an upper,to go with my m4gery,and according to Wikipedia,they were built in house by seal armorers,but they are no pics.does anyone have any pics of them in use..?.thanks Stump
3/24/2007 9:14:51 PM EDT
[#29]

Originally Posted By stumppy:
Guys all these Recces are so nice,but i have a question..are these rifles used in combat.?.i am wanting to build an upper,to go with my m4gery,and according to Wikipedia,they were built in house by seal armorers,but they are no pics.does anyone have any pics of them in use..?.thanks Stump


I asked an East Coast SEAL Sniper buddy of mine the same question-because the only "Recce's" I've seen have been "clones". Well, if nobody has ever seen any pics of actual Recce's in use-then what the hell are you "cloning".
I understand "Recce" to be a concept. Most of the rifles you see members build fit that concept very well.

I received this email response from my buddy regarding the Recce. Apparently the actual Recce's are whole lot simpler than some of the fancy stuff you see posted and they don't call them Recce's.


The RECCE rifle as I understand it was our (NSW) version of the SPR. It came about through various channels, mostly guys just tricking out M4's for Helo sniper stuff or otherwise. We had a Low power Leupold variable that was available for a while that was tweaked by premier. The actual Recce was used by NSWDG for a while and they still have all sorts of differant rifle configurations. Most all our stuff uses Knights rails and (at least to start with) Obermeyer barrels. As for the barrels, if Boots can't keep up then Crane will slap just about anything on there. Knights stuff is used because we have contracts and make Reed rich, not cause it's the best. As for barrel lentgh, I think most configs havea 16 inch barrel. The idea is just an acurrate light weight M4 wit ha low power variable. Nothing too special really.

3/25/2007 1:39:44 AM EDT
[#30]

Originally Posted By vmpglenn:
6.8SPC 16" midlength, LT 12.0. Very handy, shoots where you point it.

www.visuality.com/personal/6_8/68_lt12.jpg


Flippin' fantastic!
LaRue Tactical Supporter, Former Air Assault Guy & SOPMOD Poster Child.
3/25/2007 4:33:47 AM EDT
[#31]
height=8
Originally Posted By Lawman734:
height=8
Originally Posted By stumppy:
Guys all these Recces are so nice,but i have a question..are these rifles used in combat.?.i am wanting to build an upper,to go with my m4gery,and according to Wikipedia,they were built in house by seal armorers,but they are no pics.does anyone have any pics of them in use..?.thanks Stump


I asked an East Coast SEAL Sniper buddy of mine the same question-because the only "Recce's" I've seen have been "clones". Well, if nobody has ever seen any pics of actual Recce's in use-then what the hell are you "cloning".
I understand "Recce" to be a concept. Most of the rifles you see members build fit that concept very well.

I received this email response from my buddy regarding the Recce. Apparently the actual Recce's are whole lot simpler than some of the fancy stuff you see posted and they don't call them Recce's.

height=8
The RECCE rifle as I understand it was our (NSW) version of the SPR. It came about through various channels, mostly guys just tricking out M4's for Helo sniper stuff or otherwise. We had a Low power Leupold variable that was available for a while that was tweaked by premier. The actual Recce was used by NSWDG for a while and they still have all sorts of differant rifle configurations. Most all our stuff uses Knights rails and (at least to start with) Obermeyer barrels. As for the barrels, if Boots can't keep up then Crane will slap just about anything on there. Knights stuff is used because we have contracts and make Reed rich, not cause it's the best. As for barrel lentgh, I think most configs havea 16 inch barrel. The idea is just an acurrate light weight M4 wit ha low power variable. Nothing too special really.



so is it to say that the recce came before the spr..?. or durring the devlopement of the spr through the army SF community.thanks for the help..Stump
3/25/2007 6:24:55 AM EDT
[#32]

Originally Posted By stumppy:

so is it to say that the recce came before the spr..?. or durring the devlopement of the spr through the army SF community.thanks for the help..Stump



I believe after the SPR, when the Mk12 Mod1 wasn't exactly what some guys were looking for.

Someone correct me if I'm wrong on that.
3/25/2007 6:36:49 AM EDT
[#33]
The Recce was first. The SPR apparently came from the Army's desire for Recces. They took the concept too far, and it wasn't a Recce anymore.
"There is no right reason constituted by nature." Thomas Hobbes, Leviathan, 1651
3/25/2007 8:39:01 AM EDT
[#34]
I think the M4A1 with a KAC MRE and various variable scopes came first.

The SPR started off as the Special Purpose Receiver and several bbl lengths where played with -- it became Special Purpose Rifle with the 18" bbl and was typed as the Mk12 (SPR A became Mk12 Mod0 and SPR B became Mk12Mod1) [I've seen a few units with Larue tubes on both their M4A1's and Mk12's - but it never got the Mk12 Mod2 moniker]

Several units before and after had 16" "Recce's" built.

Most of the units with a large degree of latitude on these builds are extremely photo shy.


Good, Bad... I'm the guy with the Gun

Without the neccessary toughness to apply training in adverse situations, the training is valueless
3/25/2007 9:18:38 AM EDT
[#35]

Originally Posted By vmpglenn:
6.8SPC 16" midlength, LT 12.0. Very handy, shoots where you point it.

www.visuality.com/personal/6_8/68_lt12.jpg


Man, that is frickin' beautiful...
3/28/2007 3:12:20 AM EDT
[#36]
ok i have one more question,in my futher research,a recce was a upper that was added to the team members kit,that was configured to his liking.so to say that a 16"er,with a ops inc. muzzel brake ,ff railed handgaurd,low pro gas block,larue spr-e mount, leupold 1.5-5x20, flip up front and rear sights,all on a lower with the newer 6 pos colt stock wouldnt be out of the ball park ..would it..thanks..Stump
3/28/2007 10:33:37 AM EDT
[#37]

Originally Posted By stumppy:
ok i have one more question,in my futher research,a recce was a upper that was added to the team members kit,that was configured to his liking.so to say that a 16"er,with a ops inc. muzzel brake ,ff railed handgaurd,low pro gas block,larue spr-e mount, leupold 1.5-5x20, flip up front and rear sights,all on a lower with the newer 6 pos colt stock wouldnt be out of the ball park ..would it..thanks..Stump


I'd say that's sitting somewhere between second and third base.

Sounds like a nice setup, and the Leupy will work great in the SPR-E if you are a NTCH shooter.
3/28/2007 11:50:19 AM EDT
[#38]
My view of Recce.



MN
3/28/2007 12:02:08 PM EDT
[#39]

Originally Posted By vmpglenn:

Originally Posted By stumppy:
ok i have one more question,in my futher research,a recce was a upper that was added to the team members kit,that was configured to his liking.so to say that a 16"er,with a ops inc. muzzel brake ,ff railed handgaurd,low pro gas block,larue spr-e mount, leupold 1.5-5x20, flip up front and rear sights,all on a lower with the newer 6 pos colt stock wouldnt be out of the ball park ..would it..thanks..Stump


I'd say that's sitting somewhere between second and third base.

Sounds like a nice setup, and the Leupy will work great in the SPR-E if you are a NTCH shooter.


Mine worked perfectly NTCH using a 1.5
"Do you see any similarities here, sir? How long before gun control proponents realize that your .223 and my 5.56mm make the exact same sized hole? "
-richardh247
3/28/2007 9:38:50 PM EDT
[#40]

Originally Posted By M4A2_L073754:
My view of Recce.

www.toiminta-ampujat.fi/picture_library/Whisper/recon/reccelmt.jpg

MN



that is pretty sweet.
<img src=/images/smilies/anim_kill.gif border=0 align=middle> Thanks Tom <img src=/images/smilies/anim_heavy.gif border=0 align=middle>
3/28/2007 10:18:19 PM EDT
[#41]
height=8
Originally Posted By vmpglenn:
height=8
Originally Posted By stumppy:
ok i have one more question,in my futher research,a recce was a upper that was added to the team members kit,that was configured to his liking.so to say that a 16"er,with a ops inc. muzzel brake ,ff railed handgaurd,low pro gas block,larue spr-e mount, leupold 1.5-5x20, flip up front and rear sights,all on a lower with the newer 6 pos colt stock wouldnt be out of the ball park ..would it..thanks..Stump


I'd say that's sitting somewhere between second and third base. he


roger that..i would like to have a vltor or lmt,but i have 4 kids..lmao...so another upper seems a better way to spend my money right now..my m4gery can hold 2.5" groups @ 100 yards,on an eotech with the rra 6 pos stock..thanks guys you have been a gerat deal of help.o also how do i post pics of my m4gery..?,and my recce upper when im done with her..thanks..Stump
3/29/2007 12:10:35 PM EDT
[#42]

Originally Posted By mfingar:

Originally Posted By vmpglenn:
6.8SPC 16" midlength, LT 12.0. Very handy, shoots where you point it.

www.visuality.com/personal/6_8/68_lt12.jpg


Flippin' fantastic!



Thats an accurate assessment sir!
Would John Wayne be having this conversation?


Originally Posted By steve-oh:
My AR10 is still having a few minor problems. So I would probably pawn it off on someone in a SHTF situation.
3/29/2007 12:35:23 PM EDT
[Last Edit: EvilBert][Edited] [#43]
Here are my two REESE types...



3/31/2007 4:07:20 PM EDT
[#44]
what good is a recce without kifaru


4/3/2007 4:09:03 AM EDT
[#45]
Hey KEvinB you wouldnt happen to have anymore pics of that kac 16" recce would would you..with the 6 pos m4 stock..thanks abunch..Stump
4/13/2007 6:26:06 AM EDT
[#46]
I have been waiting the last three months for all the money and parts to finally get in, but it was well worth the wait. I get to sight in the new sights Saturday and I will try and get better pics then.
Still to come is the RRA 2-stage trigger and probably a better stock.
before

After
This is my setup minus the bipod for the pic.


Just remember, friendly fire isn't !
4/13/2007 9:40:35 AM EDT
[#47]

Originally Posted By M4A2_L073754:
My view of Recce.

www.toiminta-ampujat.fi/picture_library/Whisper/recon/reccelmt.jpg

MN


Damn dude, how'd you get that front KAC Flip?
4/15/2007 1:32:54 PM EDT
[Last Edit: 0612Devil][Edited] [#48]
Took some pics in crappy lighting.  Don't know if this rifle counts...










4/15/2007 3:30:38 PM EDT
[#49]

Originally Posted By yahkohb:
what good is a recce without kifaru


+1

here's mine a couple days after paint:





Ignie Ferroque

كافر
5/6/2007 12:19:47 PM EDT
[#50]
I couldn't decide whether I wanted a precision type recce, or a do it all type recce.  So, over the past few months I put these two together.



Sign up to continue the discussion

Create a free account to share your thoughts, follow topics, and connect with the AR15.COM community.

Already a member? Sign In

Previous Page
/ 220
Next Page
AR Sponsor