Posted: Yesterday 8:44:44 PM EDT
|
Today I broke a PSA barrel nut by hand without swearing or a torch or anything other than a wrench. I got a bolt catch roll pin in perfectly with no marring and no struggling. I got a trigger guard roll pin on the first try without struggling. I got both takedown pins in without launching any springs and detents across the room, never to be seen again. I found my armorer's wrench in the first place I looked. I should go buy a lottery ticket. |
Member
Joined:
Dec 2023
Posts:
12135
EE: 100% (7)
USA
|
Originally Posted By ELittlefield: https://i.imgur.com/S5Ucr0T.jpeg" target="_blank">https://i.imgur.com/S5Ucr0T.jpeg 
|
|
Originally Posted By ELittlefield: https://i.imgur.com/S5Ucr0T.jpeg" target="_blank">https://i.imgur.com/S5Ucr0T.jpeg Is that bad? |
Member
Joined:
Dec 2023
Posts:
12137
EE: 100% (7)
USA
|
Originally Posted By FS7: Is that bad? Originally Posted By FS7: Originally Posted By ELittlefield: https://i.imgur.com/S5Ucr0T.jpeg" target="_blank">https://i.imgur.com/S5Ucr0T.jpeg Is that bad? Sub-optimal. |
I don't see no Americans. I see trespassers.
Member
Joined:
Oct 2024
Posts:
655
EE: 100% (9)
USA
|
Originally Posted By FS7: Today I broke a PSA barrel nut by hand without swearing or a torch or anything other than a wrench. I got a bolt catch roll pin in perfectly with no marring and no struggling. I got a trigger guard roll pin on the first try without struggling. I got both takedown pins in without launching any springs and detents across the room, never to be seen again. I found my armorer's wrench in the first place I looked. I should go buy a lottery ticket. Now do that 50 times a day for weeks on end. 
|
|
The bolt catch roll pin is the trouble spot for me if there are any problems. Most of the time it goes in without too much of a hassle. However, sometimes it is a bitch. I think it is because of the differences in tolerances between the size of the hole and the size of the pin. |
|
Originally Posted By PCB66: The bolt catch roll pin is the trouble spot for me if there are any problems. Most of the time it goes in without too much of a hassle. However, sometimes it is a bitch. I think it is because of the differences in tolerances between the size of the hole and the size of the pin. Last week I tapped one for 6/32 for a threaded roll pin, took me all afternoon, but it was worth it. (and not a scratch!) I have a couple different bolt releases I want to try. I am now Gunsmith. Grovel before me peasants.
|
“Government is a disease masquerading as its own cure” Robert LeFevere
|
Originally Posted By PCB66: The bolt catch roll pin is the trouble spot for me if there are any problems. Most of the time it goes in without too much of a hassle. However, sometimes it is a bitch. I think it is because of the differences in tolerances between the size of the hole and the size of the pin. I bought a special starter tool just for that pin—night and day difference. Pin fits inside a flattened-on-one-side punch that doesn’t make contact with the lower at all, but is dipped in plastic anyway just in case it makes accidental contact. Long enough that the hammer doesn’t come near the lower. Best $9 spent ever. |
On Wednesdays we wear steel.
|
Originally Posted By ELittlefield: Sub-optimal. Originally Posted By ELittlefield: Originally Posted By FS7: Originally Posted By ELittlefield: https://i.imgur.com/S5Ucr0T.jpeg" target="_blank">https://i.imgur.com/S5Ucr0T.jpeg Is that bad? Sub-optimal. Some people pay extra for that |
