Posted: 8/16/2026 12:42:20 PM EDT
|
I'm one more issue with qidi and orcaslicer away from ordering an H2D and letting chynah have all my prints. Kept getting errors halfway through FTN prints on my Xplus3. Qidi support asked me to update the firmware on my printer, so I did. Then I got talked into (finally) switching from an old version of Qidislicer to Orcaslicer. No hate here, I should have done this a while ago. Now, I am getting this error when I try to upload and start prints from the slicer: Attached File It's happening with both slicers, so I think it's related to the printer, but I'm not sure how to fix this. Anyone autistic enough to understand what this is? I can sometimes connect to it through Fluidd, and checking connection to the printer through Orcaslicer is saying it can talk to the printer, so it shouldn't be just a simple connection issue. |
The hardest part about a zombie apocalypse will be pretending I'm not excited.
|
Originally Posted By Blob: Can you transfer via USB? I haven’t had time to try but once, but it acted like there was nothing in the gcode and immediately gave me the “print complete” message when I hit go |
The hardest part about a zombie apocalypse will be pretending I'm not excited.
|
Originally Posted By seek2: Have you tried printing the FTN slim? The original FTN has some overhangs a lot of slicers don't seem to like without a lot of tuning. It does it with basically anything I try. This particular print was flow cal tiles |
The hardest part about a zombie apocalypse will be pretending I'm not excited.
Land of the once free & the home of the narrative.
Joined:
Jan 2012
Posts:
28886
EE: 100% (216)
AL, USA
|
I have Orca 2.4.2 and a Plus 4 and no issues so far. Here is how mine is setup to connect if it helps at all: 192.168.1.86:10088  |
If some of you put this much fervor into your community or church, instead of arguing with people voting for the same politician, the world would be a much better place. -Skg_Mre_Lght
|
Originally Posted By OG1: I have Orca 2.4.2 and a Plus 4 and no issues so far. Here is how mine is setup to connect if it helps at all: 192.168.1.86:10088 https://www.ar15.com/media/mediaFiles/289319/4-3812443.png Mine is the same - and Ive been using Orca since I got the Plus4 You didnt SSH into the printer and update any components directly did you? |
Land of the once free & the home of the narrative.
Joined:
Jan 2012
Posts:
28887
EE: 100% (216)
AL, USA
|
Originally Posted By ManMan: Mine is the same - and Ive been using Orca since I got the Plus4 You didnt SSH into the printer and update any components directly did you? Try temporarily disabling your firewall for 60 seconds just to see if it works, you'll just need to add an exception for Orca Slicer is so. |
If some of you put this much fervor into your community or church, instead of arguing with people voting for the same politician, the world would be a much better place. -Skg_Mre_Lght
|
Originally Posted By thezentree: Might be a low disk space issue? Gonna delete all the old gcode on the printer later and see if that fixes it. This fixed it. "Hey your printer's internal storage is full and it doesn't have room for any more gcode" would have been way more helpful than a giant wall of indecipherable error code. |
The hardest part about a zombie apocalypse will be pretending I'm not excited.
|
Originally Posted By thezentree: This fixed it. "Hey your printer's internal storage is full and it doesn't have room for any more gcode" would have been way more helpful than a giant wall of indecipherable error code. It tried! Usually these errors are better formatted and easier to read, but this looks like a raw dump with all the formatting characters still included rather than affecting the format. 
|
post_count += 1
PGP: 912E3E9A194DED4E47DA0BA9D593AD70C8C12B9C
PGP: 912E3E9A194DED4E47DA0BA9D593AD70C8C12B9C