AR Sponsor
Posted: 7/3/2026 9:52:28 PM EDT
| I have the G-Lever in a BCM lower, with the SSA Trigger. nothing is binding, and the G-Lever selector works with no binding, just my trigger is dead. NOTE: I put my Radian Safety back in and everything works as normal. The trigger will fire sometime with the G-Lever on fully, but never on semi mode? |
|
This may not be your issue but I had similar symptoms with an out of spec disconnector. If you are comfortable doing so, you may want to buy a disconnector (or a few, they cost less than a shipping charge) and replace it, double check the spring is installed correctly, and try it again. Otherwise, I think any gunsmith that works on ARs should be able to diagnose and fix an FRT related issue. PS you didnt note what FRT system you are running, but I can tell you the 3pos AZ Regulator works great, but you are going to give up that G trigger pull. Given that you are running a G trigger I can say that my Arc Fire V2 with SSA also works great. I used a carbide bit w my Dremel and followed the instructions on this forum, no problem at all. One note with the Arc Fire or any FRT that uses screws to hold the safety levers: be sure to use loctite! nd if you have issues in FRT mode, check that the selector lever has not loosened. |
Member
Joined:
Dec 2023
Posts:
10759
EE: 100% (7)
USA
|
Originally Posted By shenendoah_rifleman: This may not be your issue but I had similar symptoms with an out of spec disconnector. If you are comfortable doing so, you may want to buy a disconnector (or a few, they cost less than a shipping charge) and replace it, double check the spring is installed correctly, and try it again. Otherwise, I think any gunsmith that works on ARs should be able to diagnose and fix an FRT related issue. PS you didnt note what FRT system you are running, but I can tell you the 3pos AZ Regulator works great, but you are going to give up that G trigger pull. Given that you are running a G trigger I can say that my Arc Fire V2 with SSA also works great. I used a carbide bit w my Dremel and followed the instructions on this forum, no problem at all. One note with the Arc Fire or any FRT that uses screws to hold the safety levers: be sure to use loctite! nd if you have issues in FRT mode, check that the selector lever has not loosened. He's using an Atrius G Lever. OP, if you've installed it correctly, you probably need to shave a little bit off the top of the tail of your trigger shoe. Just a tiny bit, go slow, take a little and test it, then take a little more and test again. |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
|
Originally Posted By Jonboyhst: ARIZONA REGULATOR sells his own FRT trigger system? How will does his work compared to all the other? Originally Posted By Jonboyhst: ARIZONA REGULATOR sells his own FRT trigger system? How will does his work compared to all the other? Yes, the Arizona Regulator. It is excellent. Function is on par or better with anything else, built like a tank, I’d be surprised to not get 10K rounds out of them. It will run with many G$ triggers, but info is a bit tough; G$ sent a C&D letter (should have told them to eat his shorts…), JD removed all references of Geissele from the site, but it can be set up to work with many, you’d probably want to confirm with him. Mbt as well. He sells a 3-position with a precut mil-spec trigger and modified disconnector that is the simplest solution for a drop-in 3-position for the AZR. Originally Posted By shenendoah_rifleman:. PS you didnt note what FRT system you are running, but I can tell you the 3pos AZ Regulator works great, but you are going to give up that G trigger pull. Given that you are running a G trigger I can say that my Arc Fire V2 with SSA also works great. I used a carbide bit w my Dremel and followed the instructions on this forum, no problem at all. One note with the Arc Fire or any FRT that uses screws to hold the safety levers: be sure to use loctite! nd if you have issues in FRT mode, check that the selector lever has not loosened. G$ triggers are absurdly easy to cut for the AS. No jig needed, if you want to keep that nice trigger (I like them with a 3 position), it’s hard to argue with the Arc-Fire. There is a cut guide build into the damn thing…does not get easier. Amen on the lever screws. |
|
*Le sigh ***I am not a gunsmith just a drooling idiot on the internet. Do not take my advice as you may destroy your expensive G$ trigger*** This has worked for 10 out of Ten G$ triggers. Using the V1 ARC FIRE. I have not used this for any others. Don’t blame me if you’ve got a run away dremel or your volume only goes to 11. Be gentle, use lube, make it comfortable as you violate this lovely thing. You want her to invite you back to enjoy her over and over and go faster and faster. If you’re an ogre and brute force it you get what you deserve. Alright fellas…. Let’s take a shot at a pictorial. I’ll update the post, so it may take some time to complete. * the uncut trigger is a Super Dynamic Enhanced and the modified is a Super Dynamic Combat. Same trigger dimensions so all is equal. Uncut right side SDE  Cut Right Side SDC  *UnROUNDED left side SDE  *ROUNDED left side SDC  Side by side  Side by side  Unmodified SDE  Modified SDC  Unmodified SDE  Modified SDE   |
| I did. he said to talk to the people we purchased it from. I was trying to ask him about his FRT system, and if his system would work with the SSA trigger. Me being new to the FRT world, I made a mistake, and said the word, fully auto, and he said they don't sell fully auto triggers and rudely hung up on me? |
Member
Joined:
Dec 2023
Posts:
10770
EE: 100% (7)
USA
|
Originally Posted By HKH: *Le sigh ***I am not a gunsmith just a drooling idiot on the internet. Do not take my advice as you may destroy your expensive G$ trigger*** This has worked for 10 out of Ten G$ triggers. Using the V1 ARC FIRE. I have not used this for any others. Don’t blame me if you’ve got a run away dremel or your volume only goes to 11. Be gentle, use lube, make it comfortable as you violate this lovely thing. You want her to invite you back to enjoy her over and over and go faster and faster. If you’re an ogre and brute force it you get what you deserve. Alright fellas…. Let’s take a shot at a pictorial. I’ll update the post, so it may take some time to complete. * the uncut trigger is a Super Dynamic Enhanced and the modified is a Super Dynamic Combat. Same trigger dimensions so all is equal. Uncut right side SDE https://www.ar15.com/media/mediaFiles/99571/IMG_9778-3701679.jpg Cut Right Side SDC https://www.ar15.com/media/mediaFiles/99571/IMG_9779-3701680.jpg *UnROUNDED left side SDE https://www.ar15.com/media/mediaFiles/99571/IMG_9780-3701681.jpg *ROUNDED left side SDC https://www.ar15.com/media/mediaFiles/99571/IMG_9781-3701682.jpg Side by side https://www.ar15.com/media/mediaFiles/99571/Image-3701705.jpg Side by side https://www.ar15.com/media/mediaFiles/99571/Image-3701717.jpg Unmodified SDE https://www.ar15.com/media/mediaFiles/99571/IMG_9782-3701684.jpg Modified SDC https://www.ar15.com/media/mediaFiles/99571/IMG_9783-3701685.jpg Unmodified SDE https://www.ar15.com/media/mediaFiles/99571/IMG_9787-3701706.jpg Modified SDE https://www.ar15.com/media/mediaFiles/99571/IMG_9788-3701707.jpg https://www.ar15.com/media/mediaFiles/99571/IMG_9785-3701722.jpg @HKH he's asking about an Atrius G Lever, not an ARC Fire. OP, please click "Quote" and then "Quote All" from the menu that pops up, under the post you're replying to, so we know who you're replying to. You just need to file or rotary tool and shave a tiny amount from the top of your trigger tail. It's very easy, you just need a little patience and a steady hand. You need to take barely any at all, like this:  " />And just to make sure we're all on the same page, is this what your FRT looks like?  " /> |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
Member
Joined:
Dec 2023
Posts:
10771
EE: 100% (7)
USA
| And please don't bother JD at Arizona Regulator with this. The guy who told you to do that is pranking you. He's a crochety man, who does not do work with this type of FRT. |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
| Thank you so much for helping me. I have the G Lever that is not working correctly in my BCM, Its half woking or working better in my Aero lower. I have just ordered the arc fire V2 FRT, from A5 Designs. I want an SSA pre cut trigger for the Arc Fire. I really want to purchase a new SSA pre cut trigger from someone who does it correctly, or have someone to cut my SSA trigger. |
Member
Joined:
Dec 2023
Posts:
10773
EE: 100% (7)
USA
|
Originally Posted By Jonboyhst: Thank you so much for helping me. I have the G Lever that is not working correctly in my BCM, Its half woking or working better in my Aero lower. I have just ordered the arc fire V2 FRT, from A5 Designs. I want an SSA pre cut trigger for the Arc Fire. I really want to purchase a new SSA pre cut trigger from someone who does it correctly, or have someone to cut my SSA trigger. For your Atrius G Lever, I would do it yourself. For the ARC-Fire, you can send it to Deez Nutz Tactical (yes, I'm serious, that's their name) and they'll cut it for you. Both of my usual sources for pre cut triggers (Deez Nutz and AS Designs themselves) are completely sold out of all models. I have not used Deez Nutz's cutting service, but most of my pre cut Geisseles came from them. I expect they'll do your trigger well. https://deeznutztactical.com/product/geissele-machining-services/ |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
Member
Joined:
Dec 2023
Posts:
10774
EE: 100% (7)
USA
|
Originally Posted By Jonboyhst: The only place I can find a SSA pre cut trigger is from Mid-Tier Defense. I was reading they are not that good? No personal experience with them, but one of the more prolific posters on this subforum says they butchered one of his triggers. |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
Member
Joined:
Dec 2023
Posts:
10775
EE: 100% (7)
USA
|
Originally Posted By Jonboyhst: I found a SSA pre cut trigger from Mid-Tier Defense? Give them a shot. They've been in business for a while now, so they've probably worked out the kinks. |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
Member
Joined:
Dec 2023
Posts:
10776
EE: 100% (7)
USA
|
Originally Posted By Jonboyhst: the picture you showing is that the cut for the G-Lever? Yes. You just need to take a small amount off for the Atrius G Lever. No rounding, or big cutoffs. Just shave it down a touch. |
It was not preached to the crowd,
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
It was not taught by the State.
No man spoke it aloud,
When the English began to hate.
|
If I’m not mistaken any trigger that is modified to the Atrius is now slaved to that frt. An arc fire modded trigger is still fine to use by itself. Trigger can go bang when on safe since the top was shaved. Just an fyi I know for a fact the milspec ones were since the cam was so oversized on the OG Atrius |
Horrible thread maker, EE addict, Santa's Elf
Joined:
Sep 2009
Posts:
20002
EE: 100% (583)
ME, USA
|
Originally Posted By Jonboyhst: ARIZONA REGULATOR sells his own FRT trigger system? How will does his work compared to all the other? I dropped one into my DD Mk18 and it ran like a sewing machine... In Minecraft. |
"And all that's left inside of me couldn't bring an heirloom seed to bloom..." Benjamin Tod
Horrible thread maker, EE addict, Santa's Elf
Joined:
Sep 2009
Posts:
20003
EE: 100% (583)
ME, USA
|
Originally Posted By Jonboyhst: I did. he said to talk to the people we purchased it from. I was trying to ask him about his FRT system, and if his system would work with the SSA trigger. Me being new to the FRT world, I made a mistake, and said the word, fully auto, and he said they don't sell fully auto triggers and rudely hung up on me? Nice try, ATF. 
|
"And all that's left inside of me couldn't bring an heirloom seed to bloom..." Benjamin Tod
Member
Joined:
Dec 2023
Posts:
11036
EE: 100% (7)
USA
AR Sponsor