AR Sponsor
AR-RPK Build Pictures/Ideas Part II (Page 1 of 9)
Posted: 2/6/2025 10:17:20 PM EDT
[Last Edit: caduckgunner][Edited]
|
Since the last one went into the archive. Link to the original thread https://www.ar15.com/forums/AR-15/AR-RPK-Build-Pictures-Ideas/118-782670/ Here is my new build * Poverty Pony lower w/ Gray Market Research reset trigger (not installed yet) * might move up to a A5 buffer tube and a Tubbs flatwire spring * Upper is a billet Troy that PA had on sale for $30 I think. * YHM diamond FF quad rail * Daniels Defense 18" 2sw rifle length CHF barrel if found on gunbroker for $210 plus shipping, new old stock. * I have a superlative arms rifle length piston kit, but I could not fit it under the handguard. I will see how well the gas tube holds up and change as needed. * Vortex 5X and fastfire red dot I had sitting around. Had to buy a cheap mount to help with eye relief. If it doesn't work well enough, I will remove the rear sight. * Still deciding if I want to run a flash hider or a break. Either way I plant o run my rugged suppressor on it. Thoughts or other build ideas? Attached File |
Joined:
Feb 2022
Posts:
105
EE: 0% (0)
AZ, USA
|
The Quattro lower seems like a good fit for this type of build. Attached File Attached File When shooting prone I really like ambidextrous controls. The Quattro lowers have the ambi bolt hold open I like. If you don't want the quad stack lower, look at Griffin, ADM, LWRC and SilencerCo ambi lowers. |
|
Looks OK to me. I chose a shorter (16" HB) for mine. Attached File |
"An age of glory passed like a lightning flash. The mandate of heaven passed from you but you didn't see. Times change and power passes. It is the pity of the world."
Song dynasty poet
Song dynasty poet
|
Vortex 5X and fastfire red dot I had sitting around. Had to buy a cheap mount to help with eye relief. If it doesn't work well enough, I will remove the rear sight. |
"Technique isn't something that can be taught. It's something you find on your own." - Bunta Fujiwara
|
Originally Posted By HighpowerRifleBrony: Move the rear sight in front of optic. Set to big aperture. Originally Posted By HighpowerRifleBrony: Vortex 5X and fastfire red dot I had sitting around. Had to buy a cheap mount to help with eye relief. If it doesn't work well enough, I will remove the rear sight. Yep, swap positions of the rear flip up and the optic. I really like your build. I have a similar handguard that I was thinking about using for a RPK build… but it needs a longer barrel! 22-24” is what you need to really be like the RPK. I get the utility of the 18”, but… |
|
I cheated. Klein Machining ARPK upper with M60 bipod. Dumps quick with fancy trigger Attached File |
|
Originally Posted By caduckgunner: Currently running a 6" - 9" bipod. Thinking of going taller. Was also looking at running a saw bipod, but for the cost, I cam almost get an atlas. Anyone have experience with GG&G bipods? Buddy of mine runs one of these on his Shrike uppers. It’s heavy duty, but it is UTG.  
|
|
You inspired me to throw some spare parts together. This isn't an appropriate barrel but I'll be on the hunt for one. The stock has a bit of a PKM vibe so I like that. Attached File |
|
Originally Posted By VTD: You inspired me to throw some spare parts together. This isn't an appropriate barrel but I'll be on the hunt for one. The stock has a bit of a PKM vibe so I like that. https://www.ar15.com/media/mediaFiles/26478/arpk2_jpg-3475132.JPG |
|
Originally Posted By VTD: Selektor should be here tomorrow so I'm going to give that a try in this lower. if that doesn't work I'll drop an SS in. |
|
Originally Posted By Atropian_Defector: Buddy of mine runs one of these on his Shrike uppers. It's heavy duty, but it is UTG. www.amazon.com/dp/B08HDGJTSR 
|
|
Originally Posted By VTD: You inspired me to throw some spare parts together. This isn't an appropriate barrel but I'll be on the hunt for one. The stock has a bit of a PKM vibe so I like that. https://www.ar15.com/media/mediaFiles/26478/arpk2_jpg-3475132.JPG |
|
Originally Posted By caduckgunner: Nice. I have been wanting to put a PRS Lite stock on mine also, but I need to figure out what optic I am going to use. Not sure if I am sticking with the Vortex 5x prism or not. Thinking about throwing my ACOG on it. Is that the Amazon carry handle? It is the amazon handle. The barrel and handguard are from a bear creek bolt action upper that I changed to .300blk. It's definitely a work in progress. |
|
Originally Posted By jaqufrost: Nice! Make sure to keep the hammer and bottom of the carrier well lubed. An XP mainspring will also help if you want to make sure the bcg doesn't hold back when you pull the trigger hard. I hope it's a decent unit. |
Mine has the amazon carry handle as well. I even use it as a side grip when shooting while standing, does well. February 26, 2025 |
|
Originally Posted By Atropian_Defector: Mine has the amazon carry handle as well. I even use it as a side grip when shooting while standing, does well.  https://www.youtube.com/watch?v=eSaALG4JWOc |
|
Originally Posted By Strela: Looks OK with me. I chose a shorter (16" HB) for mine. https://www.ar15.com/media/mediaFiles/6163/LMG12_2_jpeg-3224057_jpg-3457511.JPG Does that charging handle work reasonably well? No binding? |
|
Originally Posted By VTD: @Strela Does that charging handle work reasonably well? No binding? Originally Posted By VTD: Originally Posted By Strela: Looks OK with me. I chose a shorter (16" HB) for mine. https://www.ar15.com/media/mediaFiles/6163/LMG12_2_jpeg-3224057_jpg-3457511.JPG Does that charging handle work reasonably well? No binding? Yes. I really just bought it for the looks, same as the MG-42 style FH, but it works well for what I use it for. I don't think I'll ever try it on an overwatch situation. I hope.
|
"An age of glory passed like a lightning flash. The mandate of heaven passed from you but you didn't see. Times change and power passes. It is the pity of the world."
Song dynasty poet
Song dynasty poet
|
Originally Posted By Strela: Yes. I really just bought it for the looks, same as the MG-42 style FH, but it works well for what I use it for. I don't think I'll ever try it on an overwatch situation. I hope. It looks like it would be a fun addition. I'm in it mostly for grins anyway  That's a cool looking rig. |
|
Attached File Have a OTC Polonium K coming in next week to live full-time on mine. @strela who makes that charging handle again? |
|
Originally Posted By Atropian_Defector: https://www.ar15.com/media/mediaFiles/523616/IMG_7492_jpeg-3494753.JPG Have a OTC Polonium K coming in next week to live full-time on mine. @strela who makes that charging handle again? Smith Tactics. https://www.smith-tactics.com/products/smith-tactics-sk_01-3628 |
"An age of glory passed like a lightning flash. The mandate of heaven passed from you but you didn't see. Times change and power passes. It is the pity of the world."
Song dynasty poet
Song dynasty poet
|
Originally Posted By NoMoAMMO: https://www.ar15.com/media/mediaFiles/56078/20250319_132750_jpg-3494671.JPG |
My issued A4 clone is filling this role until I can build a dedicated rifle. It has a HBAR so I figured why not throw my FRT in it. It works just fine how it is, but I plan on getting a 9-13 Harris bipod for it. I have a D60 for it, but 30rd mags are a lot easier to carry and change. 
|
|
How are you guys attaching m60 style bipods. I like the close-to-muzzle attachment. I have some cheap rpk style clamp on. I actually really like it, folds to a low profile against the rail. But I had to replace all the roll pins because they were walking out on their own. Has held up since. Attached File |
|
Originally Posted By FoxValleyTacDriver: How are you guys attaching m60 style bipods. I like the close-to-muzzle attachment. I have some cheap rpk style clamp on. I actually really like it, folds to a low profile against the rail. But I had to replace all the roll pins because they were walking out on their own. Has held up since. https://www.ar15.com/media/mediaFiles/285899/1000024245_jpg-3497796.JPG Mine was machined specifically for the M60 bipod by Klein as a factory offering. |
Friend to the best firearm mfgs in the world
Joined:
Mar 2002
Posts:
34978
EE: 100% (1)
USA
| Nice! I need to get a Shrike. |
|
I got rid of that horrid carry handle and made mine that is akin to the Colt LMG one. If any one wants the STL model so they can 3D print it just send me a PM with your e-mail (has to handle 150Mb file size). Attached File |
If God didn't want them sheared, he would not have made them sheep.
|
Originally Posted By sgthatred: I got rid of that horrid carry handle and made mine that is akin to the Colt LMG one. If any one wants the model so they can 3D print it just send me a PM. https://www.ar15.com/media/mediaFiles/220681/d_jpg-3226961.JPG |
|
Originally Posted By sgthatred: I got rid of that horrid carry handle and made mine that is akin to the Colt LMG one. If any one wants the STL model so they can 3D print it just send me a PM with your e-mail (has to handle 150Mb file size). https://www.ar15.com/media/mediaFiles/220681/d_jpg-3226961.JPG |
|
Originally Posted By caduckgunner: What material did you print yours with? I have a friend who's high school aged kid is into 3D printing, so I am going to pay him to print it for me. |
If God didn't want them sheared, he would not have made them sheep.
|
Originally Posted By sgthatred: I used a print service to print it in Nylon12 and then dye it black. They use a laser to SLS (sintering the powder together) because its very accurate and strong. |
|
I just bought an old set of mod pods. Seems like an appropriate bipod choice for these too. Not my pic, but what made me think of them. Attached File |
|
Originally Posted By Atropian_Defector: I cheated. Klein Machining ARPK upper with M60 bipod. Dumps quick with fancy trigger https://www.ar15.com/media/mediaFiles/523616/IMG_5043_jpeg-3454879.JPG That's pretty perfect, right there. My vision of this concept ideally includes magnification in the optic, like a fixed 2.5-4x, or an LPVO, reason being, for when this weapon is used in the support-by-fire role, a bit farther back from an objective, OR in the defense, that extra magnification would be very useful. |
|
Originally Posted By sgthatred: I used a print service to print it in Nylon12 and then dye it black. They use a laser to SLS (sintering the powder together) because its very accurate and strong. |
|
Originally Posted By caduckgunner: @sgthatred can you share who you used? I've called around but have had no luck. @caduckgunner these will work too https://smallteamsupply.com/product/carry-handle-grips/ |
|
Originally Posted By Atropian_Defector: @caduckgunner these will work too https://smallteamsupply.com/product/carry-handle-grips/ |
|
Originally Posted By caduckgunner: @sgthatred can you share who you used? I've called around but have had no luck. Originally Posted By caduckgunner: @sgthatred can you share who you used? I've called around but have had no luck. I would do some hollowing it out to lighten it up to make it cheaper to print if you plan to use them. Originally Posted By Atropian_Defector: @caduckgunner these will work too https://smallteamsupply.com/product/carry-handle-grips/ That's almost as hideous as the original. |
If God didn't want them sheared, he would not have made them sheep.
Joined:
Oct 2024
Posts:
116
EE: 0% (0)
OR, USA
 Nothing crazy; 20 inch CL hbar, not sure of the brand 12.5 inch quad rail from ORW SA adjustable gas block Toolcraft bcg Standard charging handle with large latch Magpul prs lite Old PA 1-6 and a random dot from the extras bin for now YHM brake and Resonator K GMR super safety I'm having an issue though. Before I built this upper I was using a 12.5 midlength (adjustable gas) upper on the lower, it ran nearly flawlessly. After building this upper, it only works in semi auto, on super safe it is still semi auto. Last time I was at the range, I tried working through gas settings and that did not resolve it, I tried switching BCGs and that did not resolve it, I put a 13.9 upper on the lower and it functioned properly in all three positions. Any advice on next steps to diagnose? Thanks, gents. |
|
I have a crappy magpul bipod I take on and off. 16in mid length RRA HB 1/9, Attached File |
|
Originally Posted By sgthatred: I used Xometry I would do some hollowing it out to lighten it up to make it cheaper to print if you plan to use them. That's almost as hideous as the original. |
Recent RRH upper YT video. Failed To Load Title Current status, need to make some tweaks I think. 
|
¡Ahora sin chingas!
AR-RPK Build Pictures/Ideas Part II (Page 1 of 9)
AR Sponsor
Join the Community
Your next conversation starts here.
Create your free account to join discussions, share your experience, save topics, and connect with the AR15.COM community.
- Join discussions
- Follow topics and replies
- Connect with fellow enthusiasts
Already a member? Sign in
Stay informed by subscribing to our Newsletter