User Panel
User Panel
User Panel
|
Posted: 4/30/2017 5:14:20 PM EDT
[#1]
I hope it comes in around $225 or less. I'd like to know the length of the barrel of the rifle in the picture. I don't think it looks quite right, almost too short for the stock. Does anyone have experience with the Remington 700 stocks by Magpul?
|
|
|
|
Posted: 4/30/2017 11:38:35 PM EDT
[#2]
Judging by the thickness of the barrel, threaded muzzle and the Pmags its using, I would guess that it is an American Predator 308, 18". One of them is on my short list after how impressive my American Ranch 223 has been. I plan on picking up 2 of the magpul stocks once they are released! Love the magpul stock on my 1022, and the 700 stocks are a nice compromise IMO between the usually crap factory stocks and and an all out expensive replacement from the likes of B+C, McMillan, HS Precision, etc...
|
|
|
|
Posted: 5/1/2017 2:46:59 PM EDT
[#3]
The Remington stock is $259 without the mag well/ magazine, the ruger includes both, so $299 makes sense I guess. Does seem to be geared towards the 308 rather than any short action. Wonder if they'll eventually do a long action.
|
|
|
|
Posted: 5/3/2017 7:35:27 PM EDT
[#4]
I want one for my 300 BO.
Anything to put a few more rounds in the mag. |
|
|
|
Posted: 5/4/2017 1:26:54 PM EDT
[#5]
Quote HistoryQuoted:
I want one for my 300 BO. Anything to put a few more rounds in the mag. |
|
|
|
Posted: 5/4/2017 3:53:00 PM EDT
[#6]
I'm hoping to see one for the Rimfire version soon!
|
|
|
|
Posted: 5/4/2017 3:55:26 PM EDT
[#7]
Quote HistoryQuoted:
I'm hoping to see one for the Rimfire version soon! |
|
|
|
Posted: 5/4/2017 5:11:53 PM EDT
[#8]
Quote HistoryQuoted:
I want one for my 300 BO. Anything to put a few more rounds in the mag. |
|
|
|
Posted: 5/5/2017 12:09:52 PM EDT
[#9]
I have a Ranch in 300BLK.
How does the ACIS mags work with the smaller cartridge diameter like 300BLK & 556? I am lost on this. |
|
|
|
Posted: 5/5/2017 12:25:08 PM EDT
[#10]
Quote HistoryQuoted:
I have a Ranch in 300BLK. How does the ACIS mags work with the smaller cartridge diameter like 300BLK & 556? I am lost on this. Quote HistoryQuoted:
I have a Ranch in 300BLK. How does the ACIS mags work with the smaller cartridge diameter like 300BLK & 556? I am lost on this. The Magpul AICS mags will not work with the 223 family of cartridges, it's only for the 308 family. Quoted:
See some other magazines for 223 that are 10 round and $40. Not sure what other AICS magazines might be around. Assuming it works. |
|
|
|
Posted: 5/16/2017 11:07:55 AM EDT
[#11]
I am looking forward to the release of this stock for my ranch in .300 blackout. The magazine that comes with the RAR is absolute junk and the stock isn't much better. MDT makes AICS .223/.300 compatible 10 round magazines. I think the rifle in the Magpul photos it a ranch .
|
|
|
|
Posted: 5/16/2017 11:19:47 AM EDT
[#12]
I also have a Magpul hunter on my Remington 700 police. I actually like it better than the HS Precision stock that it came with. I love the ability to change the lop for individual preference .
|
|
|
|
Posted: 5/16/2017 9:46:47 PM EDT
[#13]
I'm patiently waiting for them to manufacture a hunter stock for the mini 14.
|
|
|
|
Posted: 8/23/2017 5:01:13 PM EDT
[#14]
Anyone know an ETA on this stock?
|
|
|
|
Posted: 8/28/2017 2:55:40 PM EDT
[#15]
Quote HistoryQuoted:
I'm patiently waiting for them to manufacture a hunter stock for the mini 14. Guaranteed to tighten the choke on your Mini14 mallard whacker. 
|
|
|
|
Posted: 10/16/2017 1:20:31 PM EDT
[#16]
I'm debating on whether to throw all of my Americans in these. It'd be nice to ditch the cheap mags and run just about all of my bolt guns off of AICS magazines
|
|
|
|
Posted: 10/17/2017 8:37:07 PM EDT
[#17]
One for my .300 BO is on the short list.
|
|
|
|
Posted: 11/4/2017 11:11:46 PM EDT
[#18]
Anybody bought one of these stocks yet????
|
|
|
|
Posted: 11/5/2017 8:21:06 AM EDT
[#19]
Quote HistoryQuoted:
Anybody bought one of these stocks yet???? |
|
|
|
Posted: 11/15/2017 5:29:02 PM EDT
[#20]
I phoned Magpul about 3 weeks ago to ask if they had any idea when a left handed "Hunter" stock would be available for my R.A.P. in 6.5Cm. I was told the right handed versions due 'late 2017' would likely be on the market Q1-2018.
The young woman I spoke with had no idea if/when a lefty would be produced so I suggested that my request for one be the first 'vote' to do so. She chuckled but offered no promises. |
|
|
|
Posted: 12/6/2017 2:29:15 PM EDT
[#21]
A lot of folks have been awaiting the availability of the Magpul stock for the Ruger American. Its coming soon, and 2:05 in this video made me laugh. :)
https://www.youtube.com/watch?v=tYDBxNKryco |
|
|
|
Posted: 12/6/2017 10:33:07 PM EDT
[#22]
Quote HistoryQuoted:
A lot of folks have been awaiting the availability of the Magpul stock for the Ruger American. Its coming soon, and 2:05 in this video made me laugh. :) https://www.youtube.com/watch?v=tYDBxNKryco |
|
|
|
Posted: 12/10/2017 1:13:48 PM EDT
[#23]
Quote HistoryQuoted:
A lot of folks have been awaiting the availability of the Magpul stock for the Ruger American. Its coming soon, and 2:05 in this video made me laugh. :) https://www.youtube.com/watch?v=tYDBxNKryco 
|
|
|
|
Posted: 1/4/2018 11:42:21 PM EDT
[#24]
Too late, too many broken promises.
I'm glad that they think broken promises are funny but I don't. I bought two MDT RAP stocks last month and will never look back. |
|
|
|
Posted: 1/9/2018 12:05:08 AM EDT
[#25]
If I based my purchases on release dates I would ALWAYS be disappointed.
For the price the Hunter Stock will no doubt be the best...for the price. |
|
|
|
Posted: 1/13/2018 3:47:56 PM EDT
[#26]
I wonder if Ruger changing mag platforms will mess with these stocks. I hope not.
|
|
|
|
Posted: 1/14/2018 12:00:19 PM EDT
[#27]
Quote HistoryQuoted:
I wonder if Ruger changing mag platforms will mess with these stocks. I hope not. |
|
|
|
Posted: 1/14/2018 12:04:49 PM EDT
[#28]
Quote HistoryQuoted:
I was wondering the same thing and if this is why the stocks haven't been released yet. They should still sell either way. Quote HistoryQuoted:
Quoted:
I wonder if Ruger changing mag platforms will mess with these stocks. I hope not. I just care about me 
|
|
|
|
Posted: 1/28/2018 12:28:01 PM EDT
[#29]
I hope that the mag change and delay means that I can benefit from the change when it finally does come out. I'm ready either way.
|
|
|
|
Posted: 1/28/2018 4:05:52 PM EDT
[#30]
Quote HistoryQuoted:
I hope that the mag change and delay means that I can benefit from the change when it finally does come out. I'm ready either way. |
|
|
|
Posted: 1/29/2018 3:49:47 PM EDT
[#31]
Ruger offers a synthetic stock for their Gunsite Scout Rifle for considerably less than the abovementioned stocks: http://shopruger.com/Ruger-Scout-Synthetic-Stock/productinfo/90574/.
Three points about this particular stock: 1) If you are using iron sights, or a properly-mounted Scout scope, the syn stock already has the correct cheek piece rise; no need for adjustment unless one wishes to mount a conventional scope with an extraordinary large ocular bell. 2) The GSR stock is internally reinforced to accept 3 sling swivel studs, thus allowing use of a Ching sling. 3) The innards of the buttstock are accessible, allowing stowage of spare parts, cleaning supplies, and anything else desired. This also allows the user to change the balance point of their rifle to suit them. That particular stock is just fine by me for its' intended purpose. I bedded the action using Brownell's Steel Bed compound, and it is much more accurate than I am. For my Mini-14, and 10-22, I prefer the stainless steel Butler Creek stock, bedded, of course, although that option might not be open to some. I doubt that I will replace the syn stock on my RAR .22RF, because it has snap-in cheek risers and the length of pull is likewise easily adjusted. Given those attributes, it's hard to justify the presumably considerable expense of a fancier stock that dues much the same thing. I'll probably bed the action, though. YMMV. |
|
|
|
Posted: 2/4/2018 1:48:10 PM EDT
[#32]
Quote HistoryQuoted:
Ruger offers a synthetic stock for their Gunsite Scout Rifle for considerably less than the abovementioned stocks: http://shopruger.com/Ruger-Scout-Synthetic-Stock/productinfo/90574/. Three points about this particular stock: 1) If you are using iron sights, or a properly-mounted Scout scope, the syn stock already has the correct cheek piece rise; no need for adjustment unless one wishes to mount a conventional scope with an extraordinary large ocular bell. 2) The GSR stock is internally reinforced to accept 3 sling swivel studs, thus allowing use of a Ching sling. 3) The innards of the buttstock are accessible, allowing stowage of spare parts, cleaning supplies, and anything else desired. This also allows the user to change the balance point of their rifle to suit them. That particular stock is just fine by me for its' intended purpose. I bedded the action using Brownell's Steel Bed compound, and it is much more accurate than I am. For my Mini-14, and 10-22, I prefer the stainless steel Butler Creek stock, bedded, of course, although that option might not be open to some. I doubt that I will replace the syn stock on my RAR .22RF, because it has snap-in cheek risers and the length of pull is likewise easily adjusted. Given those attributes, it's hard to justify the presumably considerable expense of a fancier stock that dues much the same thing. I'll probably bed the action, though. YMMV. |
|
|
|
Posted: 2/7/2018 3:33:31 PM EDT
[#33]
Quote HistoryQuoted:
What's a stock for the Gunsite rifle have to do with a RAR stock? Quote HistoryQuoted:
Quoted:
Ruger offers a synthetic stock for their Gunsite Scout Rifle for considerably less than the abovementioned stocks: http://shopruger.com/Ruger-Scout-Synthetic-Stock/productinfo/90574/. Three points about this particular stock: 1) If you are using iron sights, or a properly-mounted Scout scope, the syn stock already has the correct cheek piece rise; no need for adjustment unless one wishes to mount a conventional scope with an extraordinary large ocular bell. 2) The GSR stock is internally reinforced to accept 3 sling swivel studs, thus allowing use of a Ching sling. 3) The innards of the buttstock are accessible, allowing stowage of spare parts, cleaning supplies, and anything else desired. This also allows the user to change the balance point of their rifle to suit them. That particular stock is just fine by me for its' intended purpose. I bedded the action using Brownell's Steel Bed compound, and it is much more accurate than I am. For my Mini-14, and 10-22, I prefer the stainless steel Butler Creek stock, bedded, of course, although that option might not be open to some. I doubt that I will replace the syn stock on my RAR .22RF, because it has snap-in cheek risers and the length of pull is likewise easily adjusted. Given those attributes, it's hard to justify the presumably considerable expense of a fancier stock that dues much the same thing. I'll probably bed the action, though. YMMV. |
|
|
|
Posted: 3/23/2018 4:08:35 PM EDT
[#34]
I'm looking at getting a Ruger American Predator in 308, and would like to have the option to get the Magpul stock later. Does it make a difference if The Ruger is the version with the rotary mag (#06974) or the 3 round AI-style mag (#26974)? Will this stock fit both and allow the use of the Magpul mags?
|
|
|
|
Posted: 3/23/2018 6:55:11 PM EDT
[#35]
If only theyd make a mini-14 stock....and mags
|
|
|
|
Posted: 3/23/2018 7:18:42 PM EDT
[#36]
Quote HistoryQuoted:
I'm looking at getting a Ruger American Predator in 308, and would like to have the option to get the Magpul stock later. Does it make a difference if The Ruger is the version with the rotary mag (#06974) or the 3 round AI-style mag (#26974)? Will this stock fit both and allow the use of the Magpul mags? 2 weeks |
|
|
|
Posted: 5/17/2018 5:07:02 PM EDT
[#37]
Any signs of these in the wild yet???
|
|
|
|
Posted: 5/20/2018 3:58:29 PM EDT
[#38]
Quote HistoryQuoted:
Any signs of these in the wild yet??? Don't imagine I could be lucky enough to have them mold that stock with indications in it where I could dremel out the recess for my Predator's left handed bolt, after all this waiting either, huh? Probably too much to expect. Southpaws are still under-appreciated in today's world of CNC, CAD, easy reverse imaging, etc. Sometimes it sucks to be right handed and left eye dominate. |
|
|
|
Posted: 5/21/2018 9:12:58 AM EDT
[#39]
Quote HistoryQuoted:
I'm patiently waiting for them to manufacture a hunter stock for the mini 14. |
|
|
|
Posted: 5/21/2018 9:38:12 AM EDT
[#40]
They're too busy making bipods and clothing to finish up the Ruger stocks
|
|
|
|
Posted: 5/21/2018 1:14:10 PM EDT
[#41]
Quote HistoryQuoted:
They already make shotgun stocks Quote HistoryQuoted:
Quoted:
I'm patiently waiting for them to manufacture a hunter stock for the mini 14. |
|
|
|
Posted: 7/9/2018 1:52:43 PM EDT
[#42]
Seriously Magpul, when is this friggin stock coming out!?
|
|
|
|
Posted: 7/9/2018 3:18:51 PM EDT
[#43]
Quote HistoryQuoted:
Seriously Magpul, when is this friggin stock coming out!? |
|
|
|
Posted: 7/10/2018 12:40:50 PM EDT
[#44]
Quote HistoryQuoted:
2 weeks |
|
|
|
Posted: 7/10/2018 12:57:52 PM EDT
[#45]
Quote HistoryQuoted:
Source of info please? If so, I am pleased... :) Quote HistoryQuoted:
Quoted:
2 weeks |
|
|
|
Posted: 7/10/2018 1:42:50 PM EDT
[#46]
I preordered via Brownells 6 months ago... like an idiot. I don't think anything is happening with these now that they are redesigning around the updated Ranch rifles.
|
|
|
|
Posted: 7/27/2018 4:15:17 PM EDT
[#47]
For the record, I love Magpul products and culture, but they really dropped the ball on this Ruger American stock.
Sorry Magpul, you made me do it. Still need to get a buffer tube and carbine stock, but got the expensive part out of the way: 
|
|
|
|
Posted: 8/3/2018 12:18:40 AM EDT
[#48]
Really, for that price they can't at least include one of their AR stocks? Seriously, that is a rip off.
|
|
|
|
Posted: 8/3/2018 12:59:18 AM EDT
[#49]
So what’s your mdt stock going to cost all said and done?
|
|
|
|
Posted: 8/3/2018 8:37:04 AM EDT
[#50]
On their Instagram Post about the new 700 Pro stock, lots of people asking about the American Stocks, and they reponded to most of them saying "this month".
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
