User Panel
Oly does not stock complete .45 uppers. They assemble them as the orders come in. If they say they don't have them in stock, they are really missing some or all of the parts. You stand a better chance of buying the barrel, ejector and bolt carrier assembly separately first. Then you can buy one of their upper receivers or use any upper receiver you like.
The bolt carrier and the ejector is the same for all their pistol calibers. If the guy on the phone says no to .45 stuff, ask about 9mm or .40 parts. He may not know they are the same. I've been to their store and saw this happen myself. |
|
كافر
|
Just got off the phone with OLY. I ordered an Upper, but the are out of Mags. No problem since I'm using GG mags anyway !! Wooo Hooo!!!!!
|
|
|
Just ran 150rds through my Bazooka BAZ45 lower. Ran perfectly. No issues whatsoever. I would highly recommend these lowers to anyone looking for an AR .45 carbine. Bazooka
|
|
|
I just put my Oly kit together. I modified the upper myself. I'm having a hell of a time getting it to chamber the rounds properly. It seems like the ejector spring puts too much pressure on the bolt. Anyone have any ideas? The holes are drilled in the proper places.
Edit. I took the ejector spring out to see if that was the problem and it's not related. The bolt just doesn't seem to push the the round out of the mag properly. The round goes in at an angle and catches sideways. It's like the feed ramps are too steep. It might also help if the magazine was able to sit up a little higher so the round wouldn't have to exit the mag at such an angle. I dunno if laying the front of the feed ramp down a little would help at all. |
|
|
Try shooting it. My Oly upper wouldn't hand-cycle ammo at all, but it feeds perfect during firing. |
||
A varmint will never quit - ever. They're like the Viet Cong - Varmint Cong.
|
The ejector spring should have enough tension to hold the bolt carrier in place when you hold it up and even shake it. It will work itself out after a couple hindred rounds. It will not load right when cycling by hand as mentioned above. Drop the one round into the chamber and then let the bolt slam forward. Then insert the mag. Fire it and it should load the next rounds just fine.
|
|
كافر
|
I already shot it and had a round that wasn't fully chambered explode on me.
|
|
|
If there is way to much spring pressure, then the hole for the tail of the ejector is drilled too low. This hole is what sets the angle of the ejector spring. Too low and you have excessive spring pressure on the bolt carrier. Too high and you have weak ejection. There is no forgiveness in this hole location.
And I have to ask. Why did you fire it if the round wasn't fully seated? Was there any damage to the gun. |
|
كافر
|
I fired it because I didn't know. What do you think, I was just curious to see what would happen? Like I said, It isn't related to the spring. The feed ramps are not right. This is an Oly barrel with my own a2 upper that is drilled correctly, a Cav Arms lower, a Hahn magblock, and grease gun mags. I've tried about 6 mags so they aren't the problem. The feed ramps just aren't right on the barrel.
|
|
|
I have not come across any Oly barrel extensions with messed up feed ramps. Don't mean it can't happen, just never experienced it.
The Cav Arms mag catch could be out of spec. causing the GG mags to sit too low. It could also be that the spring is so tight against the carrier that it is slowing it down to the point of causing the round hangup similar to trying to test feed by hand. The carrier needs to be operating with all the buffer spring pressure and buffer weight possible to strip and seat the rounds correctly. |
|
كافر
|
That didn't take long!!! My OLY upper came already. Time to have some fun.
( I ordered it on the 8th. arrived on the 16th. ) |
|
|
This gentleman is now finishing AR45 lowers. Turn around time has been just a couple weeks from time of reciept of the AR45 lower from the customer or from Justin, who can drop ship from CNCGUNS.
www.thompsonmachine.net/gun.htm |
|
كافر
|
I have 2 45acp uppers that I have been using with AR lowers and modded 16rnd Uzi mags, it would be nice to put my GG mags to use. I may order a 2nd lower with thompson since I'm waiting for the 1st from KW and never know when it may be done. |
||
|
Do you know what he is charging? Have you had any in depth reviews of his work on the AR45 lowers that he has done? Thanks, Joe |
||
|
Justin e-mailed me last week and said that he is about to start another batch of 10% lowers. You can have him ship it direct or ship it yourself to Thompsonmachine. He will charge $80 to finish machining the lower and $35 to anodize or powdercoat in satin black. I have seen some of his work and it is nice. Justin said he sent a lower to him to finish, as a test, and was highly impressed.
|
|
|
That sounds good. I have one that Khalan / Mitchell Jones did that has several problems. I sent it back to him for repair but I am still not happy with it. I may just trash it and start over. I really want an AR45 lower that is worth the time and effort to register as an SBR. |
||
|
Can you post pictures of the cosmetic areas you have concerns about. We can take a look and see what we can do to address these areas in future production.
|
|
كافر
|
Nice post. I can't wait for the next batch to be ready.
|
|
|
CAS,
Thanks. I'll talk to Justin about fixing that in future runs. |
|
كافر
|
Good report, cas.
FWIW my first Oly upper would not fit my BAZ45 lower. At first I wrongly suspected the BAZ45 because the Oly had fit (with a little help from a plastic hammer on the takedown pin) a CMMG lower I'd been using while waiting for the BAZ45. But subsequent checking revealed that CMMG lower is the only one that Oly can be fitted to, while other uppers fit the BAZ45 just fine. |
|
|
I KNOW my OLY upper is whacky, because I've had to use some "love taps" (hammer) to get sights on the rail.
|
|
|
It's a go!
Got to run 120 rounds through it today. No issues what so ever. So I can now put my official "I would use him again" stamp on Thompson Machine. (and as a side note, my Khalan lower is supposed to be here on Thursday.) Thompson machine promised 3 weeks. It took 3 weeks. Khalan promised 2 weeks. It took 6 months. |
|
|
TC,
I have to tell you that the AR45 upper you built for me is really running well. My lower is a tough piece to mate though. I mean it is really tight. I got it in Jan from Khalan after a super long wait. Well, I did it the other day and now I am not sure I will be able to get them apart. I am wondering if the lower might be slightly out of spec. Have you seen this before? Erik |
|
|
I don't remember if yours is a factroy upper or a custom job. If it is custom, chance are the Khalan machined loer is slightly out of spec. Wouldn't be the first time. Some Khalan lowers have had out of spec holes. Wouldn't hurt to run a drill bit through the upper and lower holes by hand and take a very small amount of material from both holes. Or just let the assembly/disassembly wear the holes after time. |
||
كافر
|
If your going to mate the receiver halves I would suggest you use a 1/4" reamer. Remove the front pivot pin and attach the upper and lower pinning them together with the rear pivot pin. Use the reamer on the front pivot pin hole only and ream out the upper and lower at the same time. The two halves will be perfectly mated.
|
|
|
Just a question that I never even thought about until a friend I told about this conversion asked this question. When using the OLY upper and a CNC/Khalan lower, do I use a standard hammer or do I need to use a 9mm hammer?
|
|
|
Standard hammer. No funky parts required.
|
|
كافر
|
Erik, I know of at least two Oly 45 uppers (and I have one) that have the rear hole drilled at an angle not perpendicular to the upper, making it largly impossible to mount to an inspec lower. Usually if you push a pin from one side (if you don't have the pin installed in the lower) it will start and bind, and you can't start it from the other side. On my personal upper, I started from the side where the hole was most out of align and drilled rear hole in the upper with ever slightly increasing diameters until I could fit the pin all the way through. I didn't want to make it loose, so I stopped at the point where I could at least get a pin in with a rubber mallet. ~Dan |
||
|
Thanks to all. It binds like the last post states but I believe this was a custom built upper. 99.99 percent sure although I cant remember either TC. Since the above post, I have tried it on 5 AR15 lowers and 12 M-4A1 lowers. It fits like a champ on all of them which makes me think it may be the Khalan lower. I well carefully get the drill press out. Thanks for the help.
Erik |
|
|
A Khalan lower out of spec? No way! Can't be!
|
|
كافر
|
After all the heartburn then this I wont be doing business there again
|
|
|
Thats why my 2nd lower went to Thompson Machine for the 100% magic touch |
||
|
Well the AR gods have shined upon me. My lower will be heading to Thompson shortly. Tango, do I just get a standard lower parts kit? Any recommendations, brands? Is easier to build an upper or try to find one complete? Thanks.
|
|
|
Dan, You can add a third to your list. Your desciption matchs my experience with the Oly upper I got. Same cure and I stopped just after a rubber mallet is needed, but I still need a punch to get the pins started. |
|||
Women and cats will do as they please, and men and dogs should
relax and get used to the idea. -Robert A. Heinlein Drugs kicked in now, need sleep, radiation tastes funny at 7 am every day... a bit like victory. - Ginger |
The AR45 uses standard AR15 LPK. I use DPMS mostly because until yesterday I lived in MN and shipping was fast. As far as an upper goes you really only have two choices. 1. Order an Oly upper from either Oly direct or Ranier Arms. Uppers in stock are hit or miss due to availability of barrels. 2. Order just the Oly .45 BCG and ejector from Oly. Use any AR15 upper receiver, and order a 16" Thompson SMG barrel from Gun Parts Corp and send it to Kurts Kustom Firearms to have an Oly barrel extension made and mounted to the Thompson SMG barrel. The Thompson barrel has a funky taper right where the front sight base mounts so you'll need to free float the barrel and use a filp up or stationary front sight that attaches to a free float rail. All other parts are standard AR15. You can also order the barrel from Oly and just use the upper receiver of your choice. You need to drill and mount the ejector in your upper receiver. Plans are here somewhere4 on ARFCOM. The big advantage of the second option is your upper is exactly like you want it. My favorite builds are using RRA 9mm slick side flat top upper receivers without the big fat brass deflector. |
||
كافر
|
Tango thanks for the info. I will start the parts hunt in the morning. I kind of like the build it yourself idea plus KKF does some damn fine work.
|
|
|
Well I worked on these for a bit this week. Its definately the lower but I have fixed them! Will be putting lead downrange this weekend hopefully.
|
|
|
E.r.i.k.
I've been trying to IM and e-mail you for a week. It says you have an invalid username every time. Shoot me an e-mail[email protected] |
|
|
|
|
Cav-Aid 2008
http://www.ar15.com/forums/topic.html?b=1&f=5&t=680406 |
hmm any chance for thompson mags in a tangochaser rec? thompson mags are cheap and everywhere new and used,, greese gun mags are a little tougher to find now
|
|
|
Requires a whole new design to use thompson mags. They are longer front to rear due to the rib on the back and anew mag release slot would have to be cut into the mag. Having to modify the mags negates any cost savings over a GG mag.
I do have one prototype Ar45 lower that uses Thompson and GG mags iterchangeably. I haven't had time to finish the design but a Thompson mag also requires mods to the bolt carrier and the upper receiver. These mods make it more expensive than the AR45 for GG mags. |
|
كافر
|
hmm guess i'll have to start the search for greese gun mags , got any ideas where i can buy them cheap ?
|
|
|
. www.keepshooting.com/firearmaccessories/magazines/usgim3mag.htm |
||
|
FWIW I just bought a bunch of their new GG mags, I don't have my .45 ACP Carbine yet but those mags are beautiful. I have a friend who has a STEMPLE that uses unmodified GG mags and as soon as I can get to go shooting with him I'm going to try out 20 or so picked at random. |
|||
|
I've got 7 of those KeepShooting.com mags. One is still in the package but so far the other 6 have worked great. But then I"ve only got ~150rds thru the first 4 and ~100 thru the last two so that's not real conclusive but it's a good start.
|
|
Women and cats will do as they please, and men and dogs should
relax and get used to the idea. -Robert A. Heinlein Drugs kicked in now, need sleep, radiation tastes funny at 7 am every day... a bit like victory. - Ginger |
I have some of the new mags by keepshooting and they work without a hitch in my .45 uzi carbine with a GG mag conversion. They work just as good as usgi m3 mags. They are the cheapest deal at this time.
|
|
|
Gun Parts Co. |
||
|
-found a few on GunBroker for 25 bucks ea. on a dutch auction. All old original Guidelamp mfd.
|
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.