Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
Posted: 9/5/2010 10:01:22 AM EDT
Will this combination work/fit? It looks like it but dont want to waste my time ordering the rail for my SBR if not. Thanks all.
Link Posted: 9/5/2010 11:05:16 AM EDT
What is the length of your barrel???

Link Posted: 9/5/2010 12:25:10 PM EDT
11.5"
Link Posted: 9/5/2010 4:21:58 PM EDT
I am going to say no.

Have you emailed LaRue?
Link Posted: 9/5/2010 7:00:01 PM EDT
I did and am awaiting a response. Was hoping to order it today though. Keeping my fingers crossed that your wrong
Link Posted: 9/5/2010 7:12:19 PM EDT
My guess is yes it will work, I have a 12" larue rail on the 12.5 Noveske barrel and my M4-2000 fits.
Link Posted: 9/5/2010 8:42:20 PM EDT
[Last Edit: 9/5/2010 8:54:16 PM EDT by lrc]
I hope I'm wrong too, I bet it will look badass if it does.

My advice was based on looking at my 11.5 sbr w/ m4 handguards
and using my tactical tape measure to get an idea of how close the rail
would be to the end of the muzzle.

Let us know either way and post pics.

ETA:
Also go check out bravocompanyusa.com the have pictures of their ss 11.5" uppers with the LaRue gooseneck rail and
It looks like the end of the gooseneck is almost right over top of the base of the flash hider...
Link Posted: 9/6/2010 7:57:33 AM EDT
Irc......Thanks for going out of your way to help. The Bravo Company pics are nice. I will let you know.

MFS1589......Does your M42000 slide partially into the rail?
Link Posted: 9/6/2010 11:49:30 PM EDT
[Last Edit: 9/7/2010 11:03:28 AM EDT by rlarge10]
I have an 11.5" BCM upper with 10" larue rail and m4-2000. I'll see if I can get pics, but its an awesome combination. i'm almost certain that the inside diameter of the larue rail is not big enough to recess the can into it and if it were I think tripping the release to get the can off would be a PIA

eta





Link Posted: 9/7/2010 4:16:49 PM EDT
Originally Posted By rlarge10:
I have an 11.5" BCM upper with 10" larue rail and m4-2000. I'll see if I can get pics, but its an awesome combination. i'm almost certain that the inside diameter of the larue rail is not big enough to recess the can into it and if it were I think tripping the release to get the can off would be a PIA

eta

http://i205.photobucket.com/albums/bb34/rlarge10/004-15.jpg

http://i205.photobucket.com/albums/bb34/rlarge10/006-14.jpg

http://i205.photobucket.com/albums/bb34/rlarge10/007-14.jpg


Thats the rail I want to put on my 11.5" BCM... That is PURE awesome rlarge...
Link Posted: 9/8/2010 4:16:46 PM EDT
Great pics. Thanks!
Link Posted: 9/9/2010 4:26:24 PM EDT
Yes it will work. Here is my old setup 11.5" with an M4 1000.

Link Posted: 9/13/2010 3:17:46 PM EDT
Thanks for the confirmation. I can now order without worry.
Link Posted: 9/14/2010 4:31:07 AM EDT
Just because this is pretty close to what i was planning also on the sbr im waiting on, does this mean that the m4-2000 will work with the 11 inch full rail also, not just the gooseneck?
Link Posted: 9/14/2010 4:41:02 AM EDT
The Gooseneck is cut higher, I do not think the full rail will work. I did measure and with the Gooseneck you can run a 10.5" barrel and it will fit under the neck.
Top Top