User Panel
Posted: 5/24/2005 3:09:11 PM EDT
A lot of posts about here about how oil will cause all kinds of chaos on a Glock. Lets set the record straight here with some FACTS.
On one of the posts someone mentioned how oil on the firing pin will cause "Sludge". You're kidding right? We are not applying lube like you do on a fifth wheel guys. When you oil a firearm all oil/grease should then be wiped of with a Dry cotton cloth(t-shirts are great). When you are done the surface will be shiny NOT WET! Next, "Oil on the extractor will migrate to the firing pin channel" Hey knuckle head. Burnt powder, oil,brass shavings migrate through out the gun. THATS WHY YOU ARE SUPPOSED TO CLEAN IT!!!! Oh God I should'nt have to explain this, but here goes. When you get back from the range, pull out the mag. Turn the Glock over and look inside the handle on the rear surface. See all dem black circles that match the pattern of the holes on the back of your mag so you can get a count of the rounds inside? They are there because when the gun goes BANG, all the burnt powder get blown back through the mag and out dem little holes. AND ITS NOT JUST STOPPING THERE!. It gets blown through out the firearm people. In the mag, firing pin channel, frame , trigger assembly, EVERY PART. Try taking it fully apart and you'll see what I mean. And these morons who field strip it and wash it in the sink are just plain crazy, because all the dirt just gets washed out of sight and into all the tight spots like extractor surfaces, safeties, etc. Poor Mr. Glock, how does he deal with the stupid mistakes made on a very simple pistol. |
|
If you are going to come and in here and insult people, the least you could do is not post something as ridiculous as that. But then again, your post makes no sense at all to start with. If you want to put oil on the firing pin in your Glock then keep doing it. I'll just follow the guidelines set forth by Glock. I've had no problems doing this, and I see no reason to change now. |
|
|
Man what is your problem, your post makes no sense at all ........ The Quality of the trolls are going down hill..
|
|
Glock Manual pg38
WARNING: "Do not put oil inside firing pin channel or magazine. The magazine (inside and out) and breech face should be wiped dry before reassembly. Leaving solvent or lubricant in these areas could cause contamination of primers and failure to fire." I think I'll go by what Gaston recomends. |
|
Here ya go, I'll go step by step and walk you through it..............1)Take the mag out of the pistol |
||
|
2)turn the pistol upside down, and look into the handle. 3) there are 4 sides to the mag well. 4) look at the surface that is at the rear. 5) see those little black dots on the surface? Thats the burnt powder getting blown down through the mag and out the holes leaving the same pattern inside your mag well in the pistol grip. That residue gets blown throughout the gun also. get it?
|
|
+1. WTF. I miss the Old Trolls. |
|
|
I really shouldn't be suprised with the attitudes here though. I work with a know it all too. The guy hammers new bearings into place like he's driving tent pegs. I try to tell him about inner race and outer race, and how to seat a bearing, and by doing it wrong you reduce a beraings life by 50-70%. He just looks at me like I'm nuts and then bitches when he has to change the same bearings in 3 months.
Some people get very child like when you point out something they are doing wrong. |
|
So you think he is a "know it all"? |
|
|
Well, at least you know the first step to properly cleaning a Glock. |
|||
|
A retired marine friend gave me this Langenham mod FL to repair. It needed a new firing pin and a mag. I had to make a cut on the new mag for the mag catch to hold onto it, and reblued it. new pin and lubed it for him. Took him and the pistol to the range. let him shoot it first but he was all over the target. Gave him a few pointers( I get payed $25 an hour for gun maint/repair/or instruction), I took aim with the first shot and BANG, center punched the bullseye.
So I took a pistol I never saw before, fixed it, lubed and reassembled it, and shot a bullseye the first shot. Pretty good for a silly troll. |
|
|
Many new gunowners are like new home owners who have never had a yard before. They either over-water or they under-water.
|
|
The hell with the Glock manual I'm listening to Kolt from now on! |
|
|
Really? A bullseye? For Real? You are so cool... |
|
|
I must be missing something. Sure, stuff gets blown all throughout the gun. Who said that didn't happen? It's (in large part) because stuff gets blown throughout the gun that GLOCK recommends keeping the extractor and firing pin channel dry. Oil in those areas is more likely to attract problematic gunk. I don't get why it's hard to do what the manual says. It's not like there's been a rash of GLOCK failures due to underlubrication. |
|
|
Don't question a man that cleaned and lubed a gun that shot a bulleye on the first shot! Don't you dare... |
||
|
|
|||
|
PREACH ON BROTHER KOLT!!! Keep going, this is extremely educational to those of us who have opened our minds. |
|
|
|
||
|
You know, it's better to remain silent and be thought a fool, then to speak and remove all doubt. For your own sake, I really do hope that you are just a troll. |
|
|
Too late for this one. The cat is out of the bag! |
||
|
its always easy to save face and call the other guy a "troll"
|
|
I agree Kolt! Here is a guy trying to educate us; he's provided us with examples of his past experiences and you jackasses call him a troll? For God's sake he cleaned and lubed a gun that shot a bullseye! What more do you people want Amazing! |
|
|
I'm eating a tub of shooters(hot peppers and cheese balls in OIL and a loaf of Italin bread) and wondering how long a group of guys will debate an issue.
|
|
Now I think to myself why do these guys do this. It must be to make yourselves feel better.
|
|
Don't worry, I predict this thread will be coming to a quick end.
|
|
Actually my mother in law, brother in law and his wife are visiting so I'm hiding in the office killing time and staying away from them. It's entertainment, nothing more. |
|
|
IBTL! |
|
|
+1. Maybe his account will come to a quick end. |
|
|
Don't tease... |
||
|
Actually, I don't have the ability to lock a thread in this forum, but I know people who do. |
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.