User Panel
User Panel
User Panel
|
Posted: 6/13/2023 5:57:31 PM EST
[#1]
Ran 100-120 rounds through 3. No issues
|
|
|
|
Posted: 6/14/2023 7:49:08 PM EST
[#2]
I’m up to roughly 400 rounds with two failures, one of which I don’t think was mag related. One failure to feed when one mag was brand new on its first firing on a dry gun.
The other was a failure to extract that happened last week. I noticed after this happened that I hadn’t detail stripped the slide in a while and there was quite a bit of brass shavings/debris where the extractor seats due to the large firing pin hole and “breach face notch” which seems to shave off a bit brass with each firing. I also noted after detail cleaning that the extractor wasn’t holding onto rounds if there wasn’t a loaded mag in the gun. I swapped the extractor to a different one I had on hand and this went away, so the extractor may have been either worn or slightly out of spec. Suffice it to say, the FTE was likely not mag related. The 140 rounds I fired today through mag #2 after swapping the extractor were flawless. I’m going to shoot another 100 rounds through mag #1 this week and call it good. Nearly all the rounds I fired were with fully loaded mags. Between my experiences and the anecdotal reports of others I think these things are GTG and can be trusted. I do think a break in period as well as sufficient lubrication is a good idea. Either way, these seem light years ahead of the shield mags that seem to work fine for some people and are jam o matics for others. Good job PSA! |
|
|
|
Posted: 6/14/2023 8:22:10 PM EST
[#3]
Quote HistoryQuoted: I’m up to roughly 400 rounds with two failures, one of which I don’t think was mag related. One failure to feed when one mag was brand new on its first firing on a dry gun. The other was a failure to extract that happened last week. I noticed after this happened that I hadn’t detail stripped the slide in a while and there was quite a bit of brass shavings/debris where the extractor seats due to the large firing pin hole and “breach face notch” which seems to shave off a bit brass with each firing. I also noted after detail cleaning that the extractor wasn’t holding onto rounds if there wasn’t a loaded mag in the gun. I swapped the extractor to a different one I had on hand and this went away, so the extractor may have been either worn or slightly out of spec. Suffice it to say, the FTE was likely not mag related. The 140 rounds I fired today through mag #2 after swapping the extractor were flawless. I’m going to shoot another 100 rounds through mag #1 this week and call it good. Nearly all the rounds I fired were with fully loaded mags. Between my experiences and the anecdotal reports of others I think these things are GTG and can be trusted. I do think a break in period as well as sufficient lubrication is a good idea. Either way, these seem light years ahead of the shield mags that seem to work fine for some people and are jam o matics for others. Good job PSA! Awesome. Thx for the update. |
|
|
|
Posted: 6/14/2023 8:22:27 PM EST
[#4]
Quote HistoryQuoted: Ran 100-120 rounds through 3. No issues Nice. |
|
|
|
Posted: 6/14/2023 8:22:57 PM EST
[#5]
Quote HistoryQuoted: Forgot to update over the weekend. Cleaned the G48. 30 rounds more through each of my five mags. Zero malfunctions. I'm calling mine good to go and will start carrying with the PSA mags. 
|
|
|
|
Posted: 6/14/2023 8:31:07 PM EST
[#6]
|
|
|
|
Posted: 6/15/2023 8:57:08 AM EST
[#7]
I was kind of thinking PSA might release the Micro Dagger pistol this weekend since it’s Father’s Day. Be sure to watch PSA web site around 4 PM EST and see if they drop any more mags or pistols.
|
|
|
|
Posted: 6/15/2023 8:58:48 AM EST
[#8]
Quote HistoryQuoted: I was kind of thinking PSA might release the Micro Dagger pistol this weekend since it’s Father’s Day. Be sure to watch PSA web site around 4 PM EST and see if they drop any more mags or pistols. My body is ready  F5 to be on standby, thanks. |
|
|
|
Posted: 6/15/2023 11:04:08 AM EST
[#9]
Quote HistoryQuoted: My body is ready F5 to be on standby, thanks. 
|
|
|
|
Posted: 6/15/2023 11:07:37 AM EST
[#10]
Quote HistoryQuoted:  What’s funny? |
|
|
|
Posted: 6/15/2023 11:24:16 AM EST
[#11]
Quote HistoryQuoted: What’s funny? I'd tell you by PM but you have me on ignore. |
|
|
|
Posted: 6/15/2023 11:25:47 AM EST
[#12]
I would like to see some of these go through a hot/cold cycle to see how the plastic to metal bond holds up.
|
|
|
|
Posted: 6/15/2023 12:14:51 PM EST
[#13]
Quote HistoryQuoted: What’s funny? Probably that people have had issues but they don’t wanna see it. So far I’ve seen some people have issues. Some people also have no issues with the shield mags. I still have faith that hopefully these mags work cause even though I haven’t had problems with my shield mags, I don’t trust them yet. |
|
|
|
Posted: 6/15/2023 12:34:20 PM EST
[#14]
Quote HistoryQuoted: Probably that people have had issues but they don’t wanna see it. So far I’ve seen some people have issues. Some people also have no issues with the shield mags. I still have faith that hopefully these mags work cause even though I haven’t had problems with my shield mags, I don’t trust them yet. No, that wasn't why. Because of these reviews from actual users, I now have complete faith in buying, breaking in, and carrying. |
|
|
|
Posted: 6/15/2023 12:44:53 PM EST
[#15]
Quote HistoryQuoted: No, that wasn't why. Because of these reviews from actual users, I now have complete faith in buying, breaking in, and carrying. Took you off ignore… It was something from a while ago. I’m over it, you were probably having a bad day like we all do on here from time to time. Most people I throw on ignore end up banned and if they don’t I take them off after a while as long as I don’t see them continue to be a-holes. I’ve just been lazy with my ignore list lately. 
|
|
|
|
Posted: 6/15/2023 2:07:35 PM EST
[#16]
Quote HistoryQuoted: No, that wasn't why. Because of these reviews from actual users, I now have complete faith in buying, breaking in, and carrying. I want to try some but I’m not gonna sit here all day f5ing the page all day to get them. |
|
|
|
Posted: 6/17/2023 8:40:58 PM EST
[#17]
Shot around a 100 through mine. One failure to eject. Only issue encountered.
|
|
|
|
Posted: 6/18/2023 2:21:57 AM EST
[#18]
Quote HistoryQuoted: I want to try some but I’m not gonna sit here all day f5ing the page all day to get them. They announced that backordered magazines will ship by Wednesday 6-21-23 and orders will be able to be placed after that. They claim they'll be regularly available after that. No word on the frame
|
|
|
|
Posted: 6/19/2023 1:04:22 PM EST
[#19]
Another 100 through mine today. I trust them fine.
|
|
|
|
Posted: 6/19/2023 5:18:40 PM EST
[#20]
I put 240 rounds down range through these mags today with zero issues.
100 rounds of Herters, 100 rounds of PPU, 20 Sig Vmax and 20 HST 124 grain. This time I used the Mrs’s 43X At this point, I have several hundred rounds through three different guns using these magazines with zero issues. I would have no issues carrying these mags at this point. |
|
|
|
Posted: 6/19/2023 5:59:53 PM EST
[#21]
Quote HistoryQuoted: I put 240 rounds down range through these mags today with zero issues. 100 rounds of Herters, 100 rounds of PPU, 20 Sig Vmax and 20 HST 124 grain. This time I used the Mrs’s 43X At this point, I have several hundred rounds through three different guns using these magazines with zero issues. I would have no issues carrying these mags at this point. Great to hear, I plan on adding my own reviews to hopefully match everyone's here so future customers can read later and to buy with full confidence. I am thinking of buying a few boxes of the good stuff and some Fiocchi 115 FMJ. Is SGAmmo still the go to for best HST and Gold Dot prices? I'd like to buy a few more boxes just for this. |
|
|
|
Posted: 6/19/2023 6:02:01 PM EST
[#22]
@Jman_JJE
Your magazines are performing wonderful. And I am very happy that I was able to get some that were in stock
|
|
|
|
Posted: 6/20/2023 1:26:11 PM EST
[#23]
Another 100 flawless rounds this afternoon.
Only one suspected mag related failure out of 500 rounds, on a brand new mag in a dirty/dry gun. I’m satisfied… They have entered the carry rotation permanently. I have noticed they are easier to load now. I think a few cycles to help the spring “set” is necessary with these things, as they are sprung very tight from the factory. That’s not a bad thing, just something to note. Put a few mags worth of 9mm through these and carry with confidence. A+ PSA! |
|
|
|
Posted: 6/20/2023 1:30:55 PM EST
[#24]
Ya, that seems to be the wise thing to do. You all were stating the same things and then suddenly after a bunch of cycling's breaking them in right, the issue went away.
I figure 50 per mag should do it. |
|
|
|
Posted: 6/20/2023 5:00:30 PM EST
[#25]
I always load my 1911 magazines full and leave them that way for a while before I use them. I read somewhere that two weeks or more were optimal. Not sure if that's true with these or not.
|
|
|
|
Posted: 6/20/2023 5:03:28 PM EST
[#26]
Anyone tried the new “slick” mags?
|
|
|
|
Posted: 6/20/2023 5:13:27 PM EST
[#27]
Quote HistoryQuoted: Anyone tried the new “slick” mags? They just came out. I don’t even think anyone has them in hand yet. |
|
|
|
Posted: 6/20/2023 5:32:44 PM EST
[#28]
Quote HistoryQuoted: They just came out. I don’t even think anyone has them in hand yet. Has yours even shipped yet? No shipment notice on my end. |
|
|
|
Posted: 6/20/2023 6:18:11 PM EST
[#29]
Quote HistoryQuoted: Has yours even shipped yet? No shipment notice on my end. I just bought 2 today. I missed out the other day. |
|
|
|
Posted: 6/25/2023 9:08:25 AM EST
[#30]
Quote HistoryQuoted: I just bought 2 today. I missed out the other day. What is pricing? |
|
|
|
Posted: 6/25/2023 9:20:48 AM EST
[#31]
Quote HistoryQuoted: What is pricing? $29.99 for regular $32.99 for slick |
|
|
|
Posted: 6/25/2023 10:09:12 AM EST
[#32]
Is this a full metal mag with polymer coating on the front half, or is it half metal and half polymer bonded together?
|
|
|
|
Posted: 6/25/2023 10:18:50 AM EST
[#33]
Think of a metal magazine tube where the front has slots to where an injection molded polymer front is bonded to the metal tube. The PSA magazine seem to be well designed and executed to provide a reliable fifteen round mag to work within the Glock 48/43X frame dimensions. Glock releases firearms and the after market starts releasing parts to make the Glock more appealing to the masses.
I think PSA production capacity and variety will make the Micro Dagger a very profitable venture. |
|
|
|
Posted: 6/27/2023 11:28:15 AM EST
[#34]
I was able to order 2 on 6/19. It was for the Micro Slick finish which is all they had in stock. Still no update to my order so I am beginning to worry it may be cancelled.
Anyone else got any update on mags recently ordered such as order date, ship date, etc. |
|
|
|
Posted: 6/27/2023 1:04:35 PM EST
[#35]
I ordered eight of the slick mags on 6/20. Got the email confirming the order and my CC has been charged. No further updates or shipping confirmation. Was just about to post asking if anyone had received any updates too.
|
|
|
|
Posted: 6/27/2023 1:20:23 PM EST
[#36]
Quote HistoryQuoted: I was able to order 2 on 6/19. It was for the Micro Slick finish which is all they had in stock. Still no update to my order so I am beginning to worry it may be cancelled. Anyone else got any update on mags recently ordered such as order date, ship date, etc. Mine just shipped today, ordered on the same day as you. Maybe you were on the end of that stack of orders to fulfill based on who ordered before you. It's an odd thing though for their ammo orders to ship almost right away, but for anything not ammo specific it's at the speed of pondwater
|
|
|
|
Posted: 6/27/2023 5:46:23 PM EST
[#37]
Ordered 6/19 for 3 Micro Slick...received tracking today.
|
|
|
|
Posted: 6/27/2023 6:17:52 PM EST
[#38]
Ordered 6/19 and received tracking information this morning.
|
|
|
|
Posted: 6/27/2023 6:22:28 PM EST
[#39]
Quote HistoryQuoted: Ordered 6/19 and received tracking information this morning. So you ordered the normal ones before and the micro slicks too? If this is correct, would you mind sharing thoughts between the two to see if there's any discernable differences to favor one over the other? Least you could do for my help in spending your money at PA for the GPT's
|
|
|
|
Posted: 6/27/2023 6:41:25 PM EST
[#40]
That is correct and that can be arranged.
If UPS manages to got them here on Friday like the tracker says, I will be able to shoot them side by side on Saturday. |
|
|
|
Posted: 6/27/2023 7:07:09 PM EST
[#41]
Quote HistoryQuoted: I wouldnt mind trying some of the new mags but SA have been great for me so hopefully some deals will come up on people switching Quote HistoryQuoted: Quoted: One of my Buddies ordered three. I'm going to see how his do. He wants to swap out his SA mags, even though he's had no problems at all in his pistol. I'm gonna try to pick up his SA mags cheap. I wouldnt mind trying some of the new mags but SA have been great for me so hopefully some deals will come up on people switching Same. shotar’s buddy is the type who wastes money to fix things that ain’t broke. Sounds like a tard. |
|
|
|
Posted: 6/27/2023 7:22:20 PM EST
[#42]
Quoted: That is correct and that can be arranged. If UPS manages to got them here on Friday like the tracker says, I will be able to shoot them side by side on Saturday. My Micro Dagger assembled slide is out for delivery, I may try shooting with both slides on my 43X to see if there are any changes just because. Probably this weekend because I have the same delivery date as well. I'll report back and add to this. |
|
|
|
Posted: 6/27/2023 9:16:49 PM EST
[#43]
Quote HistoryQuoted: That is correct and that can be arranged. If UPS manages to got them here on Friday like the tracker says, I will be able to shoot them side by side on Saturday. Then you'll come to Mesquite?
|
|
|
|
Posted: 6/27/2023 9:37:19 PM EST
[#44]
Quote HistoryQuoted: Then you'll come to Mesquite? I have already committed to being in Poolville for new member orientation so I don’t see myself making that far East by the time things close down. I might make it out on Sunday as I have a 4 day weekend But if things go well, I will have mag reports on Saturday. |
|
|
|
Posted: 6/27/2023 11:08:31 PM EST
[#45]
Quote HistoryQuoted: I have already committed to being in Poolville for new member orientation so I don’t see myself making that far East by the time things close down. I might make it out on Sunday as I have a 4 day weekend But if things go well, I will have mag reports on Saturday. Quote HistoryQuoted: Quoted: Then you'll come to Mesquite? I have already committed to being in Poolville for new member orientation so I don’t see myself making that far East by the time things close down. I might make it out on Sunday as I have a 4 day weekend But if things go well, I will have mag reports on Saturday. Sweet! I need to bring my Sinister out to zero his left-eject Beretta, but we are job hunting for him tomorrow & then moar guns arriving Thursday. Have to be next week. Holler at me Sunday, I might have a spare badge for you. |
|
|
|
Posted: 6/30/2023 9:18:43 PM EST
[#46]
Quote HistoryQuoted: That is correct and that can be arranged. If UPS manages to got them here on Friday like the tracker says, I will be able to shoot them side by side on Saturday. My date of delivery went from today to now Monday, 03 July. 
|
|
|
|
Posted: 7/1/2023 12:30:01 AM EST
[#47]
I got mine today and will report back tomorrow after I test them out.
I’ve got the new ones and the old ones packed and ready. |
|
|
|
Posted: 7/1/2023 5:51:11 AM EST
[#48]
Still no shipping confirmation on mine ordered on 6/20.
|
|
|
|
Posted: 7/1/2023 9:04:19 AM EST
[#49]
Finally got shipping notice Thursday. Order was placed on 6/19. Supposed to get them on Wednesday.
Looking forward to trying these. |
|
|
|
Posted: 7/1/2023 9:07:11 AM EST
[#50]
Any leaked news on next time they are suppose to be in stock?
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2023 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
