Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 9/1/2002 10:47:18 AM EST
Link Posted: 9/1/2002 10:51:49 AM EST
I'll drive down there and get the address for you. I should be back in about 10 minutes.

Link Posted: 9/2/2002 3:33:36 AM EST
[Last Edit: 9/2/2002 3:34:51 AM EST by fijfi]
Here is the phone #, address and website. Glock

GLOCK Inc. USA, Canada
6000 Highlands Parkway
Smyrna, GA 30082
Tel.: +1 770 - 432 1202
Fax.: +1 770 - 433 8719

Link Posted: 9/2/2002 3:57:13 AM EST
Any gunsmith can install night sights for you.
I've used metrolight night tritium sights on both of my carry guns. They make them to fit almost all makes of handguns. I think I paid approximately a little over $100.00 for mine.
The place I bought them installed them for nothing. I've had good service from my sights.
Link Posted: 9/2/2002 4:03:45 AM EST
You can install a pair of Trijicons in your garage! C-clamp, table top, Punch, 1/4 drive socet set, peice of Hubba bubba...all thats needed. If you want instructions just holler.
Link Posted: 9/2/2002 4:36:36 AM EST
Wave go to Iron Works (the gunstore behind 1 Plice Plaza) they have the sights and proper tools and will do it while you wait and won't bugger it up. They won't chaarge you if you buy them there and they give LEOs a discount. Just call first and ask for Neil or Mat and let them know you're on the job.
Link Posted: 9/2/2002 4:46:37 AM EST
Link Posted: 9/2/2002 1:30:04 PM EST
Posted by DPMSouthpaw:

"I think I paid approximately a little over $100.00 for mine (Meprolights). The place I bought them installed them for nothing."

If you paid $100 for Meprolights then they didn't install them for nothing. ;) They only cost about $65-70 a set.

Link Posted: 9/2/2002 1:42:24 PM EST
Hey Wave, whats up with e-mails I am getting concerning NYPD Glock 19s. Supposedly Glock has milling machines set up there to make a cut in the slide to aid in clearing some wicked jams that lock the gun up tight. You may want to do that too? I put my own Mepro sights on my 19 BUT the front came loose after 100 rounds or so, even with red loctite. I redid it and its been fine but thats a tiny front screw to try torqueing and not breaking. Just a thought, if someone else did it, who has done a lot of them, it may stay put plus have a warrantee?
Link Posted: 9/2/2002 2:48:30 PM EST

I hear the firearms & tactics section is milling the 19s during firearms qualification at the NYPD range at Rodmans Neck. My question is: given these jams are specific to 9mm casings are getting stuck in the 19 ejection port (very very rare) do these jams occur in anyother caliber i.e. a .40?? Anyone know??
Link Posted: 9/3/2002 4:07:03 AM EST
Link Posted: 9/3/2002 5:00:15 PM EST
Being retired, I no longer get the freebees.
Link Posted: 9/3/2002 5:18:59 PM EST
That report was bull, they just wanted a more expensive gun (like a sig) to get rid of some budget dollars before the new fiscal year started. They backed it up with a report that the G19s malf'ed once in 450,000 rds! Now I want to know how many pistols on their force even have 450K rds through them?

Their is a big thread on this at glocktalk
Link Posted: 9/3/2002 5:34:48 PM EST
[Last Edit: 9/3/2002 6:22:24 PM EST by Supershooter]
This is what I use. Best sights out there for a Glock.

318 Glock SlantProTM (Straight EightTM)
* Fits All Glock Models
* No Gunsmithing, Easy Installation
* Same Day Installation From Heinie $159.95
Glock Installation Prices include the cost of the sights, installation, return shipping and insurance on the slide only. The day we receive your slide we install the sights and return ship via FedEx Next Day Delivery (subject to inventory on hand).


Link Posted: 9/8/2002 6:56:56 AM EST
I just saw this...I know some one who could do it. You might know him Dave Heko. Was at the last GSSF match at Pine Barrons and goes there alot. If you want I will find out for you.
Link Posted: 9/10/2002 6:11:47 AM EST
Link Posted: 9/18/2002 2:39:04 AM EST
I think they charge $59.00 and all you have to do is send the slide.
Link Posted: 9/18/2002 2:41:15 AM EST
I am in Winder, GA Smyrna is pretty close to me also. LOL
Link Posted: 9/18/2002 6:23:19 AM EST
Top Top