Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 6/12/2003 2:28:37 PM EST
GM Torch Red [img]http://www.digitalpose.com/mbr/1/6555/p/352744_7695791356725339579_vl.jpg[/img]
Link Posted: 6/12/2003 2:37:35 PM EST
[Last Edit: 6/12/2003 2:38:16 PM EST by nightstalker]
[>Q] It's so beautiful!
Link Posted: 6/12/2003 2:44:55 PM EST
Very Nice! MM419
Link Posted: 6/12/2003 2:57:15 PM EST
nice truck. great, straight frame. what was your setup for spraying it?
Link Posted: 6/12/2003 4:02:05 PM EST
Originally Posted By _twist: nice truck. great, straight frame. what was your setup for spraying it?
View Quote
$80 HVLP gun at Pepboys. $300 6HP 30 Gal Craftsman compressor at Sears. $60 DA sander Sears. $60 inline sander Pepboys. $135 1 Gal Crossfire Acrylic Enamel paint at NAPA. $35 1 Gal primer at NAPA. The good thing about doing it yourself is if you dont like it its nobodys fault but me. I can fix it or change it. If I were to spend $700 on it at a shop and then dont like it, I would be outta luck. Going to get the LINE-X spray in BedLiner FRI afternoon. $450 over the rail. Wooo Hoo!!
Link Posted: 6/12/2003 4:04:05 PM EST
tell the truth...did you buy the compressor, or just rent it from Sears hehehehe. some of the old timers will know what I'm talking about!
Link Posted: 6/12/2003 5:06:13 PM EST
My grandfather is hooking me up a with a nice compressor, and I'm going to snag a cheap gun, NAPA paint, a DA sander etc and do the same thing to both my Camaro and my dad's beater. Where did you paint yours, just in the open air or what? I'm planning to paint in the garage with fans out the windows for ventilation, with plastic up everywhere and on the ground...
Link Posted: 6/12/2003 5:12:14 PM EST
Looks good , did you put on any clearcoat?
Link Posted: 6/12/2003 5:13:49 PM EST
Nice looking paint. Did You shoot it at Your place or In a booth? If it was Your place, What did Your neighbors think of the smell & mess? I'm looking for some place to paint My 1966 Coronet, but the place I used last time went out of business. Tall Shadow
Link Posted: 6/12/2003 6:09:24 PM EST
[Last Edit: 6/12/2003 6:14:05 PM EST by 1776]
Originally Posted By Tall_Shadow: Nice looking paint. Did You shoot it at Your place or In a booth? If it was Your place, What did Your neighbors think of the smell & mess? I'm looking for some place to paint My 1966 Coronet, but the place I used last time went out of business. Tall Shadow
View Quote
I did it in the garage. I put plastic on the walls. Be carfull with fans and the water heater pilot light. They can cause a fire. You have a misting flamable substance in the air. The advantage of the HVLP gun is there is very little over spray. The neighbors did not have a problem that I know of. I didnt use any clear coat. Maybe I should. I should have taken the hood off to paint it. Any flat surface WILL collect dust. I can always take it off later and reshoot it.
Link Posted: 6/14/2003 1:45:45 PM EST
Got the Line-X bedliner Sprayed in last night. [img]http://www.digitalpose.com/mbr/1/6555/p/355281_2430591965904698748_vl.jpg[/img] [img]http://www.digitalpose.com/mbr/1/6555/p/355282_1575210960058623014_vl.jpg[/img]
Link Posted: 6/15/2003 5:51:47 AM EST
NICE! I bet it looks about 150% better? Everytime I paint a car or truck I am amazed at how nice it looks after word.
Link Posted: 6/15/2003 6:22:06 AM EST
Originally Posted By mike45acp: NICE! I bet it looks about 150% better? Everytime I paint a car or truck I am amazed at how nice it looks after word.
View Quote
I removed ALL the trim and had to weld the holes. [img]http://www.digitalpose.com/mbr/1/6555/p/69611_8168084855626822531_vl.JPG[/img] [img]http://www.digitalpose.com/mbr/1/6555/p/356062_1500166009345311689_vl.jpg[/img]
Link Posted: 6/15/2003 6:33:21 AM EST
the moldings do look good when the truck is new but after years they look junky. anyways aint it a bitch filling all those holes? I noticed on my 69 that there were little dips along the truck from the moldings :( whats the going price for a 67-72 shortbed 4x4 in your area?
Link Posted: 6/15/2003 6:57:53 AM EST
Wow! Wonderful job on the truck, its a beaut!! Love those Chevys!!! Line-x is the best liner too, love mine Dram out.
Link Posted: 6/15/2003 8:24:22 AM EST
Looks great! DA sander?
Link Posted: 6/15/2003 8:27:43 AM EST
Wow. Very sharp looking pickup. Nice job.
Link Posted: 6/15/2003 1:43:34 PM EST
Looks good. I wouldn't go with a clearcoat unless it was using deltron or some other two stage system. It'll just flake off otherwise.
Link Posted: 6/15/2003 1:56:22 PM EST
nice job on the truck. do you live in military housing?
Link Posted: 6/15/2003 2:43:11 PM EST
Outstanding job! I always loved that 67-72 body style. We had a 68 short wide bed that I've been kicking myself for ever selling. Bitchin ride.
Link Posted: 6/15/2003 3:01:05 PM EST
Originally Posted By redray: nice job on the truck. do you live in military housing?
View Quote
Not anymore. The before pic (last year) was on base housing. Thanks for the comments.
Top Top