Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 3/13/2005 6:24:59 AM EST
[Last Edit: 3/14/2005 11:47:20 AM EST by Dog1]
Ok...I have a older Tasco Super Sniper. 16x, rear focus. I noticed that the turrets were mushy in the clicks. Hard to count and feel.

Checked over on SniperHide.com for info. Here is the fix-

Goto either a Home Depot, Lowes or a Ace Hardware. Look for-

O-rings

Danco#30

7/8" OD x 3/4" ID x 1/16"


I went and found mine at Ace Hardware, in the plumbing section. I just changed them out and what a difference. I can not only close my eyes and feel the clicks, I can hear them too.

Hope this helps to any Tasco Super Sniper owner's...

Link Posted: 3/13/2005 8:13:18 AM EST
Thanks, Iv'e been looking for the fix to that problem.
Link Posted: 3/13/2005 9:41:19 AM EST

Originally Posted By AdamTheFarmer:
Thanks, Iv'e been looking for the fix to that problem.



Not a prob...you will be surprised at the difference...
Link Posted: 3/13/2005 11:15:04 AM EST

Originally Posted By AdamTheFarmer:
Thanks, Iv'e been looking for the fix to that problem.



+1
Link Posted: 3/13/2005 12:04:43 PM EST
Thanks Dog1!
Link Posted: 3/13/2005 12:22:28 PM EST
[Last Edit: 3/13/2005 12:22:48 PM EST by Dog1]
To all-you are welcome...this is what the board is supposed to be about..
Link Posted: 3/13/2005 1:37:30 PM EST
Damn, that is a huge difference.
Link Posted: 3/13/2005 1:49:15 PM EST

Taco Super Sniper mushy turret fix


Crap I thought this was about food.
Link Posted: 3/13/2005 2:31:57 PM EST

Originally Posted By NoHarmNoFAL-01:

Taco Super Sniper mushy turret fix


Crap I thought this was about food.




I was suddenly back in the 60's thinking of TACO Minibikes...!

Link Posted: 3/13/2005 2:57:11 PM EST
I really need to get a new keyboard...all those PC games that pissed me off, the key board took the brunt of my anger..
Link Posted: 3/13/2005 4:28:10 PM EST
thanks! just what i was looking for.
Link Posted: 3/13/2005 9:59:37 PM EST
good info

i have the newer ss but the windage turret is kinda mushy.


thanks for the info
Link Posted: 3/14/2005 9:59:59 AM EST

Having never taken apart a scope before, and being this is my first decent scope, could someone fill me in on what I do with the O-rings? I assume that I have to remove the turrets somehow and replace an existing O-ring?

Link Posted: 3/14/2005 11:46:01 AM EST
[Last Edit: 3/14/2005 11:46:40 AM EST by Dog1]

Originally Posted By XeroSygnal:
Having never taken apart a scope before, and being this is my first decent scope, could someone fill me in on what I do with the O-rings? I assume that I have to remove the turrets somehow and replace an existing O-ring?




There are 3 set screws per turret. Loosen all three and pull the turret cap off-



Then cut or remove the old o-ring and put the new one on...re-install the turret cap-


Link Posted: 3/15/2005 11:45:08 AM EST

Thanks Dog1. Did exactly as you described and it worked perfectly. Makes a huge difference in removing the "mushiness". Best 48 cents (cost of the two O-rings) I ever spent!

Link Posted: 3/15/2005 1:21:56 PM EST

Originally Posted By XeroSygnal:
Thanks Dog1. Did exactly as you described and it worked perfectly. Makes a huge difference in removing the "mushiness". Best 48 cents (cost of the two O-rings) I ever spent!





Not a problem...did you remember to push the turret cap all the way down? I forgot to tell you to do that...

It needs to be fully seated...it might not want to, but just twist it as you push down....
Link Posted: 3/15/2005 5:46:29 PM EST
Does anyonr know a online retailer for o rings, I went to every hardware and plumbing store in my area and there all out.
Link Posted: 3/15/2005 9:09:47 PM EST
Is there a fix for the soft, mushy BRASS knobs that get chewed up when you only tighten the turrets a normal amount so as to prevent slippage?

Or a fix for a wandering zero?


SS=POS
Link Posted: 3/15/2005 9:14:21 PM EST

Originally Posted By Dog1:

Originally Posted By XeroSygnal:
Having never taken apart a scope before, and being this is my first decent scope, could someone fill me in on what I do with the O-rings? I assume that I have to remove the turrets somehow and replace an existing O-ring?




There are 3 set screws per turret. Loosen all three and pull the turret cap off-

home.att.net/~dbmsb/wsb/media/132360/site1367.jpg

Then cut or remove the old o-ring and put the new one on...re-install the turret cap-

home.att.net/~dbmsb/wsb/media/132360/site1368.jpg



What rifle is that?
Link Posted: 3/16/2005 1:33:22 AM EST

Originally Posted By Dog1:

Originally Posted By XeroSygnal:
Thanks Dog1. Did exactly as you described and it worked perfectly. Makes a huge difference in removing the "mushiness". Best 48 cents (cost of the two O-rings) I ever spent!





Not a problem...did you remember to push the turret cap all the way down? I forgot to tell you to do that...

It needs to be fully seated...it might not want to, but just twist it as you push down....



Yup. I made note of the exact positions of each knob before I removed it and made sure I put it back to where it was when I was done.

Link Posted: 3/16/2005 5:46:12 AM EST

Originally Posted By AdamTheFarmer:
Does anyonr know a online retailer for o rings, I went to every hardware and plumbing store in my area and there all out.



E-mail me your address and I'll drop a couple in the mail to you..
Link Posted: 3/16/2005 5:46:49 AM EST

Originally Posted By windom:

Originally Posted By Dog1:

Originally Posted By XeroSygnal:
Having never taken apart a scope before, and being this is my first decent scope, could someone fill me in on what I do with the O-rings? I assume that I have to remove the turrets somehow and replace an existing O-ring?




There are 3 set screws per turret. Loosen all three and pull the turret cap off-

home.att.net/~dbmsb/wsb/media/132360/site1367.jpg

Then cut or remove the old o-ring and put the new one on...re-install the turret cap-

home.att.net/~dbmsb/wsb/media/132360/site1368.jpg



What rifle is that?



A PTR-91...
Link Posted: 3/20/2005 3:47:53 PM EST
A bump for the info...
Link Posted: 3/20/2005 10:27:10 PM EST
Link Posted: 3/21/2005 8:43:37 AM EST

Originally Posted By Big_Bear:
Thanks for the info. Tagging this for later.



You are welcome....the difference is amazing...
Link Posted: 3/24/2005 8:29:14 AM EST
Another bump for those that missed the info...
Link Posted: 4/24/2005 11:49:23 AM EST
Bump..
Link Posted: 4/25/2005 8:03:06 AM EST
Link Posted: 5/24/2005 6:09:11 AM EST
[Last Edit: 5/24/2005 6:42:06 AM EST by SWFA]
Link Posted: 6/1/2005 2:02:08 PM EST
Link Posted: 6/1/2005 6:46:05 PM EST
You should put this in the optics section.

Thanks for the info.
Link Posted: 6/9/2005 6:11:53 AM EST
Great info, thanks.
Link Posted: 6/18/2005 5:21:36 PM EST
That's good info.
Link Posted: 10/19/2005 3:38:14 PM EST
.
Link Posted: 11/11/2005 3:19:48 AM EST
BTT
Link Posted: 11/25/2005 5:44:55 AM EST
BTT
Link Posted: 12/23/2005 6:01:02 AM EST
BTT
Top Top