Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login

Site Notices
1/22/2020 12:12:56 PM
Posted: 9/15/2009 7:54:41 AM EST
What is the skinny on the company. Are the model 91 any good. How would you rate them?

I found a 91 at a local gunshop- it is marked

Interport Delta UT
Portugal
91AE0137

Is it worth anything?
Link Posted: 9/15/2009 9:38:19 AM EST
Contract type rifle like the Greek. The ones I've seen were good.
Link Posted: 9/15/2009 10:15:40 AM EST
The receivers were made by FMP in Portugal and imported by Interport.

Interport then had SW install the cocking tubes, trunnions and, barrels. SW then sent them back to Interport for final assembly using mostly FMP parts kits. The barrels are threaded with a pinned flash hider.

I'd say they're worth about $900ish for a nice specimen.

Link Posted: 9/15/2009 11:05:29 AM EST
So this is better then Cetme , worse then PTR ?
Link Posted: 9/15/2009 11:24:45 AM EST
Of the 3-4 Interport receivered guns I've handled - I'd take one before a PTR any day.


But as with any clone... YMMV.
Link Posted: 9/16/2009 7:11:01 AM EST
Interport is /was AA OK

That’s what my gun is built on. I got the barreled receiver back in 2004 for $400.00 ( JLD receivers were $200 then…. if you could get one)

The gap was set wrong so I swapped a like new FMP barrel, kept the trunion for compliance (prove that one) and built it up with FMP parts.

These should be marked on the top of the receiver ( and very lightly to boot) Mine had blank mag wells so the smith duplicated the SN # there.



.
.

.


It’s been a great rifle. Holding bolt gap nicely. The parts are genuine. For these it comes down to the builder.


JR
Link Posted: 9/16/2009 4:00:33 PM EST
What is the paddle thing inbetween the magazine and the trigger?
Link Posted: 9/16/2009 4:52:15 PM EST
Originally Posted By singtoe:
What is the paddle thing inbetween the magazine and the trigger?


mag release.
Link Posted: 9/17/2009 3:28:34 PM EST
[Last Edit: 9/17/2009 3:30:16 PM EST by singtoe]
I picked it up for $650.






I took it apart (and it comes apart very easly; the pins slide out effortlessly) and it has HK stamped bolt carrier and the HK style (not cetme) trigger group. Plus, it has the drum sight. It looks a hundred percent better then a Cetme. It doesn't even look like it has been fired. The name that is inscribed on it is very faint and not engraved or stamped very deeply. It came with an Aluminum FMP magazine.

Strangely, I could not find any letters or markings on the barrel. I'll shoot this week end...
Link Posted: 9/18/2009 12:48:47 AM EST

Originally Posted By singtoe:

I picked it up for $650.

You stole it!
Link Posted: 9/18/2009 7:35:32 AM EST
Yeah you got a great deal.


Originally Posted By singtoe:


Strangely, I could not find any letters or markings on the barrel. I'll shoot this week end...


That would be the US barrel.

What is the bolt gap?

JR
Link Posted: 9/18/2009 4:11:28 PM EST
Originally Posted By fortydelta:
Originally Posted By singtoe:
What is the paddle thing inbetween the magazine and the trigger?


mag release.


Looks like "Tach Latch II" I have one on my HK91. Worth every penny of the $50 I spent on it.

Top Top