Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
9/19/2017 7:27:10 PM
Posted: 10/1/2002 6:36:06 PM EDT
Where can you get the dry moly (or whatever it is) that is on USGI mags. I checked all the hardware stores in my area and no one has it.
Anyone know of a specific product? Thanks.
Link Posted: 10/1/2002 6:39:28 PM EDT
Contact Georgia Precision. They do have the product you are looking for.
Link Posted: 10/2/2002 12:23:38 PM EDT
Birchwood Casey sells one, here's a site that carries it:
http://www.ballisticproducts.com/products/GunCareChem/guncare.htm
Link Posted: 10/2/2002 12:26:03 PM EDT
Dick's SportingGoods(not sure if this is a national chain or just midwest) carries the Birchwood Casey moly lube.
Link Posted: 10/2/2002 7:08:45 PM EDT
Go to any industrial hardware supply house.
Link Posted: 10/2/2002 8:30:09 PM EDT
You're looking for "Perma-Slik G" which is the Mil Spec. moly coat found on USGI Mags. Says so on the can.

Do a search on "Perma-Slik G" and you'll find the source.

Method of use:

1. Disassemble, Clean, Degrease with Simple Green and dry.

2. Lightly sand mag body with "Fine" sand paper. I like to use the Foeam Sanding Blocks. Lightly sand floor plate.

3. Suspend mag. by hooking from ceiling with close hanger through the mag catch hole, or use a plastic coat hanger slid into the bottom of the mag body as a "Holder" while spraying.

4. Lightly spray on 1 coat.

5. Let dry to touch and lay on paper towel covered cookie sheet and bake in oven at 200 degrees for 30 minutes. (No it won't screw up the oven!)

6.Repeat #4 an #5

7. Let cool.

8. Lightly spray floor plate with "Flat Black" Rustoleum spray paint. 1 coat will do. Let dry overnight.

9. Reassemble

10. To remove "Powder Coat" (which will rub off pretty quick anyway. It's really just overspray.), rub the mag body down with a cotton rag impregnated with a light lubricant like 3 in 1 oil, or WD-40.

That's it! Remember that the magazine was designed to be a "Disposable" device. Therefore the original moly coat is not "Bullet Proof". You will see wear at the mag catch hole after a few insertion and extractions of the mag.

This is great fun and you can actuallyt make some fairly good profits if you buy the "Very Used" USGI mags for under $10.00. Refurbished mags go for around $20.00 to $25.00 each for 30 rounders. More for 20 rounders.

Hope this helps.

Link Posted: 10/3/2002 11:24:31 AM EDT
Here's a thread on Neely Industries in Arlington, TX. $12.50/can (minimum 2 cans) + shipping.

www.ar15.com/forums/topic.html?b=3&f=17&t=139209

HTH, Gabe
Link Posted: 10/4/2002 2:50:31 AM EDT
Link Posted: 10/5/2002 7:53:21 PM EDT
Link says $16 :-(


Originally Posted By Georgia-Precision:

Click Here for Online Ordering!

www.georgiaprecision.com/cats/catarmag.htm


Our current price is $13.50 per can. One can will refinish about 25-20 round mags.

Thanks,
Tommy
GPSS
478.994.4560

www.georgiaprecision.com

Link Posted: 10/13/2002 1:35:59 PM EDT
BROWNELLS,ANY TYPE YOU WANT,SPRAY,DUST,PASTE,ETC,ETC.
Top Top