Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 7/8/2003 6:31:41 AM EST
I was about to order my 14.5" M4 upper from Bushmaster for my RR sendra conversion. I'm building this up in pieces -- so far I have a Knights RAS and a QD bracket only.

In terms of ordering the upper, the next thing I'll add with likely be an Aimpoint. If I'm doing that, do I need a flip down front sight? BM will install one of their front sights for me at no extra cost other than than $100 bucks they charge for the sight. Is that worth doing? Or should I order the standard front sight?
Link Posted: 7/8/2003 11:13:11 AM EST
BUIS are a good idea. I am planning to get one from Bushmaster myself. Which rear sight are you going with?
Link Posted: 7/8/2003 11:58:21 AM EST
I haven't decided yet. As I'm going in stages, I thought I might start with the sight on the A3 handle. People seem most fond of the GG&G sight, I'd like to hear what you think of that.
Link Posted: 7/8/2003 12:28:05 PM EST
GG&G products are nice, but in short supply it seems. I went with the PRI front, very basic, and has a hood feature that protects the front sight post. If you need to attatch a sling GG&G is the way to go. Also check out the ARMS #40 rear sight.
Link Posted: 7/8/2003 1:11:08 PM EST
Link Posted: 7/8/2003 1:28:14 PM EST
Originally Posted By SinistralRifleman: I have the BMAS sights (front and rear) on my 20" rifle with Elcan, and they work well and look good. [url]http://www.cavalryarms.com/ELCAN1.jpg[/url]
View Quote
What kind of front sight block do you have mounted?
Link Posted: 7/8/2003 5:17:37 PM EST
Originally Posted By SinistralRifleman: I have the BMAS sights (front and rear) on my 20" rifle with Elcan, and they work well and look good. [url]http://www.cavalryarms.com/ELCAN1.jpg[/url]
View Quote
Why did you place the rear sight that far ahead?
Link Posted: 7/8/2003 10:14:53 PM EST
Link Posted: 7/9/2003 2:44:21 AM EST
Originally Posted By SinistralRifleman: So I can get propper eye relief with the Elcan. ...its there in the event the the Elcan gets dropped on a rock (unlikely) or is shot off my rifle (even more unlikely), and the "Indians" are coming over the wall
View Quote
Uum, have you practiced the indians coming over the wall. Cause i would suspect that the rear sight would be unusable if the elcan was and AFAIK the elcan's going to take some time to get off.
Link Posted: 7/9/2003 6:26:46 AM EST
BMAS triple mount gas block - does that work if you have a Knight's RAS installed?
Link Posted: 7/9/2003 7:11:54 AM EST
Phil and all I did quite A bit of research on this subject I found the following, take it for what its worth. -BMAS Flip upsites Lock in place up and down and are realativly inexpensive compaired to others. -GGG are excellant except the one for the picatinny ral does not LOCK up, therefor if bumped it flips down, Surprise! -Best Back up site IMHO is the ARMS#40 or #38 swan sleeve w/ #40 attached. -I dont really see a need for a flip up front site almost all optics can see over post if mounted with proper mounts. I personally run an ARMS #38 Extended rail which includes the #40 site with a fixed front site on my Armalite. M15A4 this allows me to use an Aimpoint without the spacer, low profile, and cowitness if I choose or not. When I mount my TA11D on top instead of Aimpoint, I can only barely see the front post in bottom of the scope, If I look for it. If you need the front flip up, get one that locks!! BMAS front site is very rugged but get the Tri-rail gas block and site that fits it, dont get the V-match type and clamp on site. it is a bitch to keep from rotating during clamp on installation, youll drive yourself bonkers. chuck
Top Top