Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
10/20/2017 1:01:18 AM
9/22/2017 12:11:25 AM
Posted: 8/29/2005 10:22:15 AM EDT
[Last Edit: 8/29/2005 10:24:33 AM EDT by BlowStuffUp]



(Uzi Threads on rear of barrel to accommodate Gemtech Mossad Suppressor.)

5" Stainless Barrel with 1/2 x 28 tpi front and 14mm uzi rear $160.00
5.5" flash hider $16.95
9mm Complete Bolt $150.00
Hahn precision mag block $175.00
Ramping for 9mm bolt $65.00
RAS Panels 11 rib x2 $21.90
RRA Upper Receiver A4 $105.00
Tungsten weight added to bolt $50.00
Verticle Foregrip $24.99
YHM RAS Carbine Length $95.95


total cost of upper = $864.79 (not including sights)


Special thanks to SBR7_11 answering all my questions about the build.
Link Posted: 8/29/2005 10:40:43 AM EDT
Link Posted: 8/29/2005 10:48:50 AM EDT
That's a sweet set up. Nice job!

Link Posted: 8/29/2005 12:42:36 PM EDT
nice!


Link Posted: 8/29/2005 6:18:23 PM EDT

Originally Posted By BlowStuffUp:
9mm Complete Bolt $150.00


Special thanks to SBR7_11 answering all my questions about the build.




While we on the subject of "RRA" 9mm bolt.... verify the object holding the extractor in place... we have a couple topics running in regards to malfunctioning rifle and common item is the RRA bolt. Install a roll pin of correct diameter and length if you find that the object holding the extractor in place is indeed not a "proper" roll pin.

Link Posted: 8/30/2005 2:55:37 AM EDT
Thats one very nice looking set up
Link Posted: 8/30/2005 5:16:47 AM EDT
Where did you get the barrel and FS?
Thanks
Link Posted: 8/30/2005 8:39:29 AM EDT

Originally Posted By WSAR15:
Where did you get the barrel and FS?
Thanks



As seen in the first post: (click the "blue")

5" Stainless Barrel with 1/2 x 28 tpi front and 14mm uzi rear $160.00

5.5" flash hider $16.95
Link Posted: 8/30/2005 2:29:56 PM EDT
[Last Edit: 8/30/2005 2:30:34 PM EDT by joeblack]

Wow, nice set up.


Hey, I threaded the UZI threads on that barrel !
Link Posted: 8/30/2005 2:49:21 PM EDT
[Last Edit: 8/30/2005 4:33:14 PM EDT by Matt_B]

Originally Posted By SBR7_11:
While we on the subject of "RRA" 9mm bolt.... verify the object holding the extractor in place... we have a couple topics running in regards to malfunctioning rifle and common item is the RRA bolt. Install a roll pin of correct diameter and length if you find that the object holding the extractor in place is indeed not a "proper" roll pin.

Big +1. I just had to deal with this problem myself. Minor pain in the butt though I could have easily avoided.
Link Posted: 8/30/2005 7:49:18 PM EDT

Originally Posted By joeblack:
Wow, nice set up.


Hey, I threaded the UZI threads on that barrel !



hey thanks for all the work you did for me. job well done! hopefully i will be able to try it out this weekend. Too bad i have a few more months till i get my suppressor paperwork approved. :-(
Top Top