Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 12/25/2005 11:21:10 AM EST
What is the best and easiest way to permanantly attach a Phantom to a 14.5" M4 barrel, and how do I go about doing it?
Link Posted: 12/25/2005 11:40:03 AM EST
Link Posted: 12/25/2005 3:31:06 PM EST
What do you mean by a blind hole?
Link Posted: 12/25/2005 3:38:57 PM EST
[Last Edit: 12/25/2005 3:39:32 PM EST by HeavyMetal]
Link Posted: 12/25/2005 4:14:08 PM EST
I had a thread going with pics that I can't lay my hands on right now, sorry.

Danny
Link Posted: 12/26/2005 9:34:46 AM EST
Thanks for the replies.



Should the holes be drilled where the red dot is?

I don't see how this would be permanant. Do you have to drill into the threads a little too, so that the metal dowell is actually pinning something? If not wouldn't the pin just be filling the hole in the flash hider that was drilled?
Link Posted: 12/26/2005 9:37:11 AM EST
Link Posted: 12/26/2005 9:39:09 AM EST
Ok, Thank you.
Link Posted: 12/26/2005 9:40:54 AM EST
The YHM logo is on the bottom,my pin is through the H in the center of the diamond.
I recommend ADCO for a perfect finished job.
Link Posted: 12/26/2005 9:46:03 AM EST
you only need one hole in the thing (at least according to the ATF inspectors who came through the shop) in the thing. Just so long as it can't be taken off without cutting.
Link Posted: 12/26/2005 10:23:20 AM EST
Link Posted: 12/28/2005 11:00:44 AM EST
[Last Edit: 12/29/2005 1:54:58 PM EST by Psychojeeper]
How I plan to do mine is to drill one hole at the bottom side of the flash hider and thread it for a short set screw. Install the flash hider and secure the set screw tightly, it will crush into the threads as it does so. Then weld over the screw, smooth it over, bead blast it and parkerize or finish with Duracote, etc as you like. This is similar to the method used by Bushmaster and others to permanately secure the flash-hider/muzzle brakes.

John
I am a soldier. I fight where I'm told, and win where I fight"
Gen. G.S. Patton
Link Posted: 12/28/2005 11:14:10 AM EST
Just out of curiosity, would it be alright to drill a hole from the front....crud, I am not good at explaining things like this....

Parallel to the bore, drill a hole that cuts into the threads of both the FH and the barrel and a little tack weld inside for the pin, but no refinishing necessary. The The pin would be driven from the muzzle.

I need more coffee.
Link Posted: 12/28/2005 11:57:19 AM EST
Link Posted: 12/28/2005 1:57:59 PM EST
I did mine by soldering it on. I torched it to red hot. Seems to be on very tight.

No doubt in my mine it will pass the BATF 200/300 degree loctite test.
Link Posted: 12/28/2005 2:33:41 PM EST
http://www.adcofirearms.com/shopservices.cfm?page=shop

If it is just a barrel, ADCO will do it for 25 bucks plus shipping, they did my BM 14.5/Phantom, five day turn around.
Top Top