Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 12/21/2005 6:04:01 AM EST
[Last Edit: 12/23/2005 12:39:02 PM EST by 556Cliff]
Is 35/39 foot pounds for the rifle buffer tube to tight or just right? It is the MIL-SPEC but it just sounds to tight to me.
Link Posted: 12/21/2005 1:34:19 PM EST
Just make it tight enough. It isn't really a part that needs a torque wrench to dial in IMO.
Link Posted: 12/21/2005 3:01:41 PM EST
I just make it tight then recheck after a range trip.Never had one loosen.
Link Posted: 12/22/2005 8:22:38 AM EST
BTT.
Link Posted: 12/22/2005 11:20:50 AM EST
Just has to be tight enough to keep the detent down and seat with the rear of the reciever.

Proper, by the book, tourqing is not necissary.
Link Posted: 12/22/2005 3:21:24 PM EST
I tighten it down then stake it in place.

I've had 2 come loose and don't want it to happen again.

WIZZO
Link Posted: 12/22/2005 5:04:15 PM EST
[Last Edit: 12/22/2005 5:06:47 PM EST by 556Cliff]

Originally Posted By WIZZO_ARAKM14:
I tighten it down then stake it in place.

I've had 2 come loose and don't want it to happen again.

WIZZO



That's for carbine collapsible stocks, I'm talking about rifle tube extensions.
Link Posted: 12/22/2005 8:43:32 PM EST

Originally Posted By 556Cliff:

Originally Posted By WIZZO_ARAKM14:
I tighten it down then stake it in place.

I've had 2 come loose and don't want it to happen again.

WIZZO



That's for carbine collapsible stocks, I'm talking about rifle tube extensions.



Whoops, missed the rifle part.

In that case, I snug it up with the cut-out in the handle of the carbine stock wrench, and call it good.

WIZZO
Link Posted: 12/23/2005 10:30:41 AM EST

Originally Posted By 556Cliff:
...carbine stocks only have to be torqued on at around 40 inch pounds which is a little less than 3 and a half foot pounds.



The torque spec for carbine stocks is 38/42 foot pounds.
Link Posted: 12/23/2005 12:33:30 PM EST
[Last Edit: 12/23/2005 12:35:08 PM EST by 556Cliff]

Originally Posted By M4Madness:

Originally Posted By 556Cliff:
...carbine stocks only have to be torqued on at around 40 inch pounds which is a little less than 3 and a half foot pounds.



The torque spec for carbine stocks is 38/42 foot pounds.



Sorry, I got that torque spec from the tacked thread "Headspace, Torque values, and Barrel Break-in" by DoulbleFeed in this forum. I didn't know the info was wrong.
Link Posted: 12/23/2005 2:19:56 PM EST

Originally Posted By 556Cliff:

Originally Posted By M4Madness:

Originally Posted By 556Cliff:
...carbine stocks only have to be torqued on at around 40 inch pounds which is a little less than 3 and a half foot pounds.



The torque spec for carbine stocks is 38/42 foot pounds.



Sorry, I got that torque spec from the tacked thread "Headspace, Torque values, and Barrel Break-in" by DoulbleFeed in this forum. I didn't know the info was wrong.



I haven't seen the thread in question. Your thread just got me curious, so I went and looked it up in my manual from the armorer's class I attended. It definitely says foot pounds.
Top Top