Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
Member Login
Site Notices
1/25/2018 7:38:29 AM
Posted: 12/19/2005 10:03:30 AM EST
you will need

2 feet of 2X1 channel iron (usally about $2 a foot)
4 inchs 3/8x1 1/4 bar stock (under $1)
19/64 118deg bit
4 inch sidegrinder

start by setting a tg in your channel 4-5 from end and marking it with a pen (i sandblasted so you could see)



next center puch your marks



now drill with 19/64 bit just till the hole stops getting bigger



take your 4 inch piece of 1 1/4x3/8 bar and grind down both sides (to remove rounded edges)
to 1.16 and bevel the top edge in to clear your lower rails



AND YOUR DONE
a rivet jig for under 5 bucks

heres pics of it being used and the results



Link Posted: 12/19/2005 10:37:52 AM EST
Where can you find the channel iron?
Link Posted: 12/19/2005 10:38:01 AM EST
thanks.

hope this gets put in the BIY sticky thread, if not, it's saved to my HD.

Caspian
Link Posted: 12/19/2005 10:40:59 AM EST
if you have any metal yards in your area, you'll probably be able to find it in the "scrap" section. The price of scrap here is $0.39/lb. It gets expensive quick depending how much you need. However the scrap sections are generally pretty small.

if it wouldn't cost an arm and a leg to ship, i'd try to get ya some from my local yard. However, by the time you figure in shipping on even a 5 inch piece it will get cost prohibitive.


Originally Posted By tapeo1:
Where can you find the channel iron?

Link Posted: 12/19/2005 10:52:28 AM EST
yea you can get it about anywhere i got some from a scrap dumpster

Link Posted: 12/19/2005 4:11:58 PM EST
If you are making your own jig it will help a lot
if you transfer the hole pattern from the receiver rather than
from the trigger guard itself.
I recently made a jig for my polish kit using the triggerguard
but when I went to assemble , the rivets didn't fit in the jig
because the TG was sprung smaller than it needed to be to
fit the receiver.
I was able to use the jig singly but it would have been nice
to do them all at once.
Link Posted: 12/19/2005 4:21:47 PM EST
well if you have a 1 piece jig a flat would work better but with 2
you need to use the trigger guard to tell you how far apart the 2 pieces need to be
the guard needs to be in good shape tho
Link Posted: 12/19/2005 5:25:52 PM EST
Now thats American ingenuity at its finest. Nice job socandyman.
Link Posted: 12/19/2005 5:46:04 PM EST
Thanks for the tip, I will be on my way to the scrapyard in the morning....gotta finish tooling up for the pistol build
Link Posted: 12/19/2005 6:12:42 PM EST
how did you rivet the last rivet that is next to the pistol grip
Link Posted: 12/19/2005 6:23:41 PM EST
just turn your rec sideways and use any 1 of the 4 divets
Link Posted: 12/19/2005 6:25:50 PM EST
dam your smart
Link Posted: 12/20/2005 6:31:53 AM EST
[Last Edit: 12/20/2005 6:32:39 AM EST by Fishpaw]
For even less, you could make the dimples in some flat steel bar, place them on top of your vise , opened enough to fit the trigger guard, and hammer the rivets flat inside the receiver with a hammer and a bucking bar.
Link Posted: 12/20/2005 6:57:59 AM EST

Originally Posted By Fishpaw:
For even less, you could make the dimples in some flat steel bar, place them on top of your vise , opened enough to fit the trigger guard, and hammer the rivets flat inside the receiver with a hammer and a bucking bar.



Yep . . . I did 4 receivers with this exact solution.

Disconnector
Link Posted: 12/20/2005 9:27:22 AM EST
Still the homebuild king... very cool.
Link Posted: 12/20/2005 12:21:01 PM EST

Originally Posted By Fishpaw:
For even less, you could make the dimples in some flat steel bar, place them on top of your vise , opened enough to fit the trigger guard, and hammer the rivets flat inside the receiver with a hammer and a bucking bar.



Or dimple the tops of the jaws of your vise.
Link Posted: 12/20/2005 1:04:41 PM EST
I love the elegant simplicity of socandyman's jig, but I used Fishpaw's method exactly. I have a Plinker jig on the way that I will use for my next two builds.

rob
Link Posted: 12/21/2005 2:35:10 AM EST
This REALLY needs to be a sticky. C'mon mods, please post it permanantly
Link Posted: 12/22/2005 3:09:05 AM EST
socandyman you are a genius!
Link Posted: 12/22/2005 1:02:57 PM EST
nice,..very nice,..

think you could wield the two haves together at the ends for more strength?
Link Posted: 12/22/2005 2:23:00 PM EST
shure you could altho all the pressure is going strait down so it isnt really needed
Link Posted: 12/22/2005 2:26:27 PM EST

Originally Posted By socandyman:
shure you could altho all the pressure is going strait down so it isnt really needed




you dont know my luck do you?........anyways,...send me a email if you can on how mych it would cost for you to put one together for me.


have a merry x-mas
Link Posted: 12/22/2005 7:36:51 PM EST
you rock dude
Link Posted: 12/27/2005 7:00:48 AM EST
[Last Edit: 12/27/2005 7:05:35 AM EST by me223]
Top Top