Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
BCM
User Panel

Site Notices
Posted: 12/12/2018 10:13:23 PM EDT


I've had this for a few hours now .

I have been reading so much on these things lately

Changes in mag release, change in mag design . Changes because of rolling pin and dropping slide plate

So this one has the ambi mag release and I have the double notch magazines .
Is the mag release hard .? . not in the least  Is it harder than a glock or M&P.  ?   Yes
It has the small notch between the back plate and slide .

Looking forward to putting a few hundred rounds through it soon
Link Posted: 12/13/2018 12:01:14 AM EDT
[#1]
You’ve chosen...wisely!    This is the Glock killer!
Link Posted: 12/13/2018 12:32:30 AM EDT
[#2]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
You’ve chosen...wisely!    This is the Glock killer!
View Quote
This. This. AND THIS.
Link Posted: 12/13/2018 6:08:55 PM EDT
[#3]
I just picked one up today as well.  fits all my glock holsters.  trigger is nicer than any stock glocks.  may just replace my g19 as my edc.
Link Posted: 12/15/2018 1:55:27 AM EDT
[#4]
Welcome to the new addiction.
Link Posted: 12/15/2018 3:02:18 PM EDT
[#5]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
You’ve chosen...wisely!    This is the Glock killer!
View Quote
Highly doubt that one CZ cannot saturate the US market with enough pistols and they do not practically give the pistol away to LEO.
Link Posted: 12/16/2018 6:53:14 AM EDT
[#6]
Take your pistol and have some fun shooting. Remember when reading about your pistol in the internet, one persons issue gets repeated thousands of times on different forums and the posts never go away. I love my P10C. David
Link Posted: 12/16/2018 7:20:57 AM EDT
[#7]
I'm pretty impressed with mine...
hopefully you will be as well !
Link Posted: 12/17/2018 10:10:01 PM EDT
[#8]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Take your pistol and have some fun shooting. Remember when reading about your pistol in the internet, one persons issue gets repeated thousands of times on different forums and the posts never go away. I love my P10C. David
View Quote
Everything with a grain of salt

Had a short amount of time today to run 200 rounds through it .

Really liked it. No problems today. Shot Federal, Blazer Brass and wolf

Going to change out the suppressor sights soon
Link Posted: 12/29/2018 6:51:37 PM EDT
[#9]
UPDATE

300 rounds today . So at 500 rounds a few things

The mag release is a little easier . The slide release is still pretty tight.

Shot Blazer, Blazer brass, Monarch Brass and Federal.

No issues with any of those .

The one thing I'd call a performing issue is slide lock .
On an empty mag it locks back about 50% of the time .
Link Posted: 12/29/2018 7:34:28 PM EDT
[#10]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
The one thing I'd call a performing issue is slide lock .
On an empty mag it locks back about 50% of the time .
View Quote
Try shooting one handed with you thumb tucked down out of the way and see if the slide locks back when empty.  You might be riding the slide release and not knowing it.  I've even seen a few people touching the right side ambi release with the top of their hand also.  David
Link Posted: 12/29/2018 10:14:24 PM EDT
[#11]
My slide lock and mag release were stiff when new as well,
I cycled both while watching tv, both wore in nicely.
If the slide lock doesn't improve with grip change,
get in touch with CZ customer service, they're very
Good to deal with, I'm sure they'd take care of you.
I replaced a .100 Dawson fo front sight on mine today
With a .115....much better, the gun' s a pleasure to shoot!
Link Posted: 12/29/2018 10:52:45 PM EDT
[#12]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Try shooting one handed with you thumb tucked down out of the way and see if the slide locks back when empty.  You might be riding the slide release and not knowing it.  I've even seen a few people touching the right side ambi release with the top of their hand also.  David
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:
The one thing I'd call a performing issue is slide lock .
On an empty mag it locks back about 50% of the time .
Try shooting one handed with you thumb tucked down out of the way and see if the slide locks back when empty.  You might be riding the slide release and not knowing it.  I've even seen a few people touching the right side ambi release with the top of their hand also.  David
I'll pay attention next time I shoot. Watch the thumbs
Link Posted: 1/5/2019 1:58:24 AM EDT
[#13]
Ya the slide lock issue is most likely just your grip. I had to change the way I placed my thumbs so that I wasn't interfering with the slide release.
Close Join Our Mail List to Stay Up To Date! Win a FREE Membership!

Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!

You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.


By signing up you agree to our User Agreement. *Must have a registered ARFCOM account to win.
Top Top