Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
BCM
User Panel

Arrow Left Previous Page
Page / 2
Posted: 11/16/2018 9:00:48 PM EDT
A 10 ohm 1 watt metal oxide resistor?

I'm changing the turn signals on my Yamaha Zuma 125 from incandescent to LED.

I bought a LED flasher relay but all 4 lights flash.

After some google-ing, I found out I need 2 resistors as mentioned earlier.

Now that Radio Shack is gone, where could I buy resistors locally?
Link Posted: 11/16/2018 9:03:16 PM EDT
[#1]
Quoted:
A 10 ohm 1 watt metal oxide resistor?

I'm changing the turn signals on my Yamaha Zuma 125 from incandescent to LED.

I bought a LED flasher relay but all 4 lights flash.

After some google-ing, I found out I need 2 resistors as mentioned earlier.

Now that Radio Shack is gone, where could I buy resistors locally?
View Quote
Probably nowhere. Try Ebay, amazon, digikey, mauser, etc.
Link Posted: 11/16/2018 9:04:18 PM EDT
[#2]
Radio Shack on Amazon, duh  


Link Posted: 11/16/2018 9:04:41 PM EDT
[#3]
Don't they make 'resistor kits' for just this thing?
Link Posted: 11/16/2018 9:05:08 PM EDT
[#4]
Quoted:
A 10 ohm 1 watt metal oxide resistor?

I'm changing the turn signals on my Yamaha Zuma 125 from incandescent to LED.

I bought a LED flasher relay but all 4 lights flash.

After some google-ing, I found out I need 2 resistors as mentioned earlier.

Now that Radio Shack is gone, where could I buy resistors locally?
View Quote
Where is locally?
Link Posted: 11/16/2018 9:05:24 PM EDT
[#5]
It’s futile
Link Posted: 11/16/2018 9:05:25 PM EDT
[#6]
Amazon
Link Posted: 11/16/2018 9:07:27 PM EDT
[#7]
www.jameco.com carries many of the component parts the Rat Shack used to.

Aldo, try www.digikey.com and www.mouser.com.
Link Posted: 11/16/2018 9:12:21 PM EDT
[#8]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Amazon
View Quote
Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
Link Posted: 11/16/2018 9:13:20 PM EDT
[#9]
Ali express.
Link Posted: 11/16/2018 9:13:30 PM EDT
[#10]
You know that Radio Shack still exists, don't you?
There was a "2-tier system" within RS. First tier was the corporate-owned RSs. 2nd tier was the shops which were franchises: owned by independant individuals. The 2nd tier shops are (mostly) still open, and  still have those racks and drawers of individual components.
Google shows at least 3 locations in Ohio.
Link Posted: 11/16/2018 9:17:16 PM EDT
[#11]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
View Quote
I’m thinking he’s asking where can he walk into a store and buy them, not where to order them online.

It is a fair point that these stores and similar have mostly disappeared. Many reasons for that and I’d argue most of them are valid, but it does suck when you (or the OP in this case) are in the middle project and now has to wait for online delivery.
Link Posted: 11/16/2018 9:19:34 PM EDT
[#12]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Where is locally?
View Quote
Close to my house.
Link Posted: 11/16/2018 9:19:51 PM EDT
[#13]
Frys, if you want a walk-in store
Link Posted: 11/16/2018 9:20:09 PM EDT
[#14]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:
Amazon
Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
I know, but I want it now.
Link Posted: 11/16/2018 9:20:58 PM EDT
[#15]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
It’s futile
View Quote
Link Posted: 11/16/2018 9:21:33 PM EDT
[#16]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
You know that Radio Shack still exists, don't you?
There was a "2-tier system" within RS. First tier was the corporate-owned RSs. 2nd tier was the shops which were franchises: owned by independant individuals. The 2nd tier shops are (mostly) still open, and  still have those racks and drawers of individual components.
Google shows at least 3 locations in Ohio.
View Quote
Closest one is 45 min away.

I was hoping someone would tell me I can buy at best buy or Lowe's or something.
Link Posted: 11/16/2018 9:22:07 PM EDT
[#17]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
I’m thinking he’s asking where can he walk into a store and buy them, not where to order them online.

It is a fair point that these stores and similar have mostly disappeared. Many reasons for that and I’d argue most of them are valid, but it does suck when you (or the OP in this case) are in the middle project and now has to wait for online delivery.
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:

Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
I’m thinking he’s asking where can he walk into a store and buy them, not where to order them online.

It is a fair point that these stores and similar have mostly disappeared. Many reasons for that and I’d argue most of them are valid, but it does suck when you (or the OP in this case) are in the middle project and now has to wait for online delivery.
Yes!

Thank you!
Link Posted: 11/16/2018 9:24:21 PM EDT
[#18]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
You know that Radio Shack still exists, don't you?
There was a "2-tier system" within RS. First tier was the corporate-owned RSs. 2nd tier was the shops which were franchises: owned by independant individuals. The 2nd tier shops are (mostly) still open, and  still have those racks and drawers of individual components.
Google shows at least 3 locations in Ohio.
View Quote
The RS we had went from a marvelous place with bins and drawers full of discrete components back in the 70' and 80's to a cell phone and toy store for the last several years before they closed.
Link Posted: 11/16/2018 9:24:50 PM EDT
[#19]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Yes!

Thank you!
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:
Quoted:

Or ebay.

Seriously - What you're trying to do is not unusual - and plenty of folks sell the part you need to do it.
I’m thinking he’s asking where can he walk into a store and buy them, not where to order them online.

It is a fair point that these stores and similar have mostly disappeared. Many reasons for that and I’d argue most of them are valid, but it does suck when you (or the OP in this case) are in the middle project and now has to wait for online delivery.
Yes!

Thank you!
We knew that,  but its 8:22pm and nothing is going to be open anyway. Plus that 2 day wait from Amazon is the "not planning ahead tax".
Link Posted: 11/16/2018 9:25:48 PM EDT
[#20]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Frys, if you want a walk-in store
View Quote
Thanks but none in Ohio.

We do have a Mendelsons, never been there.

They might have it.

Kinda near the ghetto though.
Link Posted: 11/16/2018 9:27:42 PM EDT
[#21]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

We knew that,  but its 8:22pm and nothing is going to be open anyway. Plus that 2 day wait from Amazon is the "not planning ahead tax".
View Quote
Lol.

I'm willing to wait until tomorrow morning for it.

Im too drunk to drive anyway.
Link Posted: 11/16/2018 9:28:55 PM EDT
[#22]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

I know, but I want it now.
View Quote
Better get out te paper clips and pencil lead then!
Link Posted: 11/16/2018 9:30:22 PM EDT
[#23]
Are you near a Micro Center? I don't know for sure that they'll have what you need, but I do know that the one near me has a section where they sell soldering stuff and breadboards and whatnot.
ETA: Here's what they show on their website: https://www.microcenter.com/category/4294910343/electronic-components
Link Posted: 11/16/2018 9:30:53 PM EDT
[#24]
HobbyTown near me carries all RS electronics parts now. Nothing on their website, but big selection in store with draws full of Radio Shack marked stuff
Link Posted: 11/16/2018 9:31:37 PM EDT
[#25]
I have a Fry's Electronics locally. Awesome place
Link Posted: 11/16/2018 9:34:14 PM EDT
[#26]
My Radio Shack haul from earlier this week.  There are still a few around.

Attachment Attached File


Went in for solder,  flux, tinner and braid.  Then he offered me this station that has been discontinued for years.  He had a lot of new/updated stations,  But I have this same station that I have put hundreds of hours on and it works better than my Weller station.  I told him make me a deal I cant refuse..  He came back with 45 bucks.  
Well...  I couldn't refuse.  


Without knowing where you live,  that might be a tough one.  I would see if there are any audio/astrostart installers.  I have a small shop that caters to home theater, car audio and sat/cable installers that carries that stuff here locally,  I hit that up fairly often.
Link Posted: 11/16/2018 9:35:42 PM EDT
[#27]
any of your friends work for a company that has a maintenance dept? If so have them go to the maintenance shop and see if they can get you one.
Link Posted: 11/16/2018 9:36:07 PM EDT
[#28]
Why it how does someone with 6k post count start a thread like this?  Google/bing/your choice in search engine brings up multiple site to purchase.

I guess I am just venting after dealing with stupid customers today that can’t figure out the simplest of shit.
Link Posted: 11/16/2018 9:36:13 PM EDT
[#29]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
My Radio Shack haul from earlier this week.  There are still a few around.

https://www.AR15.Com/media/mediaFiles/183526/1116181926_jpg-741388.JPG

Went in for solder,  flux, tinner and braid.  Then he offered me this station that has been discontinued for years.  He had a lot of new/updated stations,  But I have this same station that I have put hundreds of hours on and it works better than my Weller station.  I told him make me a deal I cant refuse..  He came back with 45 bucks.  
Well...  I couldn't refuse.  


Without knowing where you live,  that might be a tough one.  I would see if there are any audio/astrostart installers.  I have a small shop that caters to home theater, car audio and sat/cable installers that carries that stuff.  
View Quote
I need you to take me shopping with you sometime. You always seem to find the bargains!
Link Posted: 11/16/2018 9:36:22 PM EDT
[#30]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Lol.

I'm willing to wait until tomorrow morning for it.

Im too drunk to drive anyway.
View Quote
I wish I was drunk!
There's this place in Columbus..

COLUMBUS OHIO ELECTRONIC COMPONENT STORE
Link Posted: 11/16/2018 9:36:51 PM EDT
[#31]
+1 Mouser
Link Posted: 11/16/2018 9:38:43 PM EDT
[#32]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Better get out te paper clips and pencil lead then!
View Quote
Thanks!

Just fabricated this sweet piece.

Its #2 lead.

Installing now!
Link Posted: 11/16/2018 9:38:45 PM EDT
[#33]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
I need you to take me shopping with you sometime. You always seem to find the bargains!
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:
My Radio Shack haul from earlier this week.  There are still a few around.

https://www.AR15.Com/media/mediaFiles/183526/1116181926_jpg-741388.JPG

Went in for solder,  flux, tinner and braid.  Then he offered me this station that has been discontinued for years.  He had a lot of new/updated stations,  But I have this same station that I have put hundreds of hours on and it works better than my Weller station.  I told him make me a deal I cant refuse..  He came back with 45 bucks.  
Well...  I couldn't refuse.  


Without knowing where you live,  that might be a tough one.  I would see if there are any audio/astrostart installers.  I have a small shop that caters to home theater, car audio and sat/cable installers that carries that stuff.  
I need you to take me shopping with you sometime. You always seem to find the bargains!
I still haven't went to get that Fluke bench meter yet.  

He still has it,  I have been procrastinating too much over things lately.  My wife is in rough shape and out of work for a while again.  
Link Posted: 11/16/2018 9:38:49 PM EDT
[#34]
craigslist most likely, unless you have some kind of electronics supply or a repair shop, doubt the repair shop would sell but you never know.
Link Posted: 11/16/2018 9:40:27 PM EDT
[#35]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Thanks!

Just fabricated this sweet piece.

Its #2 lead.

Installing now!
http://i.imgur.com/0yYEaYI.jpg
View Quote
Wirewound and everything! I'd guess about .04 ohms?
Link Posted: 11/16/2018 9:40:56 PM EDT
[#36]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
+1 Mouser
View Quote
I have ordered from Mauser,  Newark online and Digikey.  All are GTG.

I love Digikey,  They have a city desk here in town.  I can look online and see if the item is in the in-town warehouse.  If I have them ship it,  ittl be here next morning.

Or I can go pick it up!  
Link Posted: 11/16/2018 9:41:35 PM EDT
[#37]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Wirewound and everything! I'd guess about .04 ohms?
View Quote
Wind it tighter!
Link Posted: 11/16/2018 9:41:48 PM EDT
[#38]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Are you near a Micro Center? I don't know for sure that they'll have what you need, but I do know that the one near me has a section where they sell soldering stuff and breadboards and whatnot.
ETA: Here's what they show on their website: https://www.microcenter.com/category/4294910343/electronic-components
View Quote
Thanks!

Too far away though.

I've bought several PCs from them long ago.
Link Posted: 11/16/2018 9:42:34 PM EDT
[#39]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
HobbyTown near me carries all RS electronics parts now. Nothing on their website, but big selection in store with draws full of Radio Shack marked stuff
View Quote
There is a RC place not too far away.

I'll call them in the morning!
Link Posted: 11/16/2018 9:43:03 PM EDT
[#40]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Close to my house.
View Quote
What city?
Link Posted: 11/16/2018 9:44:50 PM EDT
[#41]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
My Radio Shack haul from earlier this week.  There are still a few around.

https://www.AR15.Com/media/mediaFiles/183526/1116181926_jpg-741388.JPG

Went in for solder,  flux, tinner and braid.  Then he offered me this station that has been discontinued for years.  He had a lot of new/updated stations,  But I have this same station that I have put hundreds of hours on and it works better than my Weller station.  I told him make me a deal I cant refuse..  He came back with 45 bucks.  
Well...  I couldn't refuse.  


Without knowing where you live,  that might be a tough one.  I would see if there are any audio/astrostart installers.  I have a small shop that caters to home theater, car audio and sat/cable installers that carries that stuff here locally,  I hit that up fairly often.  
View Quote
Nice haul.

I use hakko at work.

We have a tone of shit there, no resistors though.
Link Posted: 11/16/2018 9:45:08 PM EDT
[#42]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
any of your friends work for a company that has a maintenance dept? If so have them go to the maintenance shop and see if they can get you one.
View Quote
Ain't got no friends.
Link Posted: 11/16/2018 9:45:54 PM EDT
[#43]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Why it how does someone with 6k post count start a thread like this?  Google/bing/your choice in search engine brings up multiple site to purchase.

I guess I am just venting after dealing with stupid customers today that can’t figure out the simplest of shit.
View Quote
Your post count..... those are rookie numbers.
Link Posted: 11/16/2018 9:48:36 PM EDT
[#44]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
I wish I was drunk!
There's this place in Columbus..

COLUMBUS OHIO ELECTRONIC COMPONENT STORE
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:

Lol.

I'm willing to wait until tomorrow morning for it.

Im too drunk to drive anyway.
I wish I was drunk!
There's this place in Columbus..

COLUMBUS OHIO ELECTRONIC COMPONENT STORE
Nice but need closer to Dayton.
Link Posted: 11/16/2018 9:48:57 PM EDT
[#45]
I forgot!  
Just a thought.

A BWD or ignition ballast resistor from your local parts store?

I am unsure on their specs.  But I have two in my ZX6R for the led turn signals.  It works!  
Link Posted: 11/16/2018 9:50:56 PM EDT
[#46]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Wirewound and everything! I'd guess about .04 ohms?
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:

Thanks!

Just fabricated this sweet piece.

Its #2 lead.

Installing now!
http://i.imgur.com/0yYEaYI.jpg
Wirewound and everything! I'd guess about .04 ohms?
It no worky.
Link Posted: 11/16/2018 9:51:39 PM EDT
[#47]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Better get out te paper clips and pencil lead then!
View Quote
Sometimes what we post tells things about us.  From yours I surmise you must be nearly as old as I.  And my birth ushered in the Korean War.

A #1 lead worked better than #2 or #3.
Link Posted: 11/16/2018 9:51:58 PM EDT
[#48]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

It no worky.
View Quote
Too much stray inductance!
Link Posted: 11/16/2018 9:53:25 PM EDT
[#49]
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Wind it tighter!
View Quote View All Quotes
View All Quotes
Discussion ForumsJump to Quoted PostQuote History
Quoted:
Quoted:

Wirewound and everything! I'd guess about .04 ohms?
Wind it tighter!
Now you tell me!

Now I need to buy more harness smoke!

I just lost a bunch.
Link Posted: 11/16/2018 9:53:28 PM EDT
[#50]
Discussion ForumsJump to Quoted PostQuote History
Quoted:

Closest one is 45 min away.

I was hoping someone would tell me I can buy at best buy or Lowe's or something.
View Quote
Auto parts stores sell those resistors.

https://www.oreillyauto.com/detail/b/sylvania-5022/lighting---electrical-16777/interior-lighting-25100/led-replacement-bulbs-20874/e6ac682cd82e/sylvania-red-load-equalizer/loadrslbx2/4743126
Arrow Left Previous Page
Page / 2
Close Join Our Mail List to Stay Up To Date! Win a FREE Membership!

Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!

You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.


By signing up you agree to our User Agreement. *Must have a registered ARFCOM account to win.
Top Top