Warning

 

Close

Confirm Action

Are you sure you wish to do this?

Confirm Cancel
BCM
Member Login

Site Notices
Posted: 1/9/2010 1:23:36 AM EDT
[Last Edit: 4/7/2010 1:19:51 AM EDT by Cypher15]
just like it says, id like to have a tacked reference thread of the projects in this forum for easy finding.
when posting the link, please provide:
Name/type of project
Link
and a small picture if you have one.






 happy smithing and machining







I will update OP as we go
Projects so far:
Bren Gun Kit:






http://www.ar15.com/forums/topic.html?b=6&f=49&t=301522
SKS Stock:






http://www.ar15.com/forums/topic.html?b=6&f=49&t=300855
Crowning:




http://www.ar15.com/forums/topic.html?b=6&f=49&t=308232
Edge Pro Knife Sharpener:



http://www.ar15.com/forums/topic.html?b=6&f=49&t=310536



Rem 870 Rear Sight Base:

http://www.ar15.com/forums/topic.html?b=6&f=49&t=311207&page=1&#2757541
 
Link Posted: 4/2/2010 11:53:09 PM EDT


Link Posted: 4/7/2010 1:20:04 AM EDT
another added

Link Posted: 4/18/2010 9:39:57 PM EDT
Remington Model 1900 KED Shotgun re-stocking
http://www.ar15.com/forums/topic.html?b=6&f=49&t=312314
Link Posted: 4/20/2010 1:45:51 AM EDT
http://www.ar15.com/forums/topic.html?b=6&f=47&t=312475



Stopping the flop of Winchester M94 triggers.
Link Posted: 4/20/2010 1:47:40 AM EDT
Link Posted: 6/11/2010 10:22:34 AM EDT
Bren Gun project has been shelved. I will start a new thread when this project is picked back up.

Link Posted: 1/17/2011 12:03:40 AM EDT
[Last Edit: 1/17/2011 12:05:24 AM EDT by kingjamez]
My AR-15 Lower project: My YouTube Channel
Link Posted: 1/18/2011 10:48:42 AM EDT
[Last Edit: 1/18/2011 2:03:13 PM EDT by AeroE]
Link Posted: 1/18/2011 1:35:16 PM EDT
Marlin 183 Take Down Rebuild
Here
Link Posted: 1/18/2011 1:36:54 PM EDT
[Last Edit: 1/18/2011 2:05:45 PM EDT by AeroE]
Link Posted: 10/18/2017 9:07:37 PM EDT
I posted this elsewhere but here probably makes the most sense.

The crossfeed on my lathe, a 1943 Monarch 12ck, had about 0.090" lash so I set about making a new lead screw and nut.   It was challenging.  The screw was 7/8-4LH acme with an OAL of 24".  This resulted in me making some material compromises from the 41xx screw and bronze nut to an 1144SP screw and Delrin nut.  After some pencil fiddlin, I determined Delrin was up to the task and set forth.

Step one was to turn a tap, the first one I've ever made.  It didn't work as well as an OSG, but it measured right and cut some threads. Much relief was added after I took this pic.
Attachment Attached File

Step two was to create the nut.  Straight forward mill work there.

Step three was the screw.  With planned cuts I was able to keep my TIR and taper very low over the shaft's lengths and diameters.  The screw measures about 0.001"/1" lead error.  Certainly not factory quality, but I'll take it.

Attachment Attached File


I didn't get any pics of the cutting in action, I was pretty concentrated on not botching the job.  Heres the screw and nut together on the plate, and then again as they're loaded into the taper attachment slide's bearing block.
Attachment Attached File

Attachment Attached File


I learned a lot in this project...like how to turn your mill into a tool grinder.   Monarch wanted $1600 (5years ago) for this screw/nut combo, and while there's would have been better I dont think they'd be justifiably better than my $50 effort.
Link Posted: 2/10/2021 2:03:37 AM EDT
A past project of mine to put a non-reciprocating left side charge handle on my AR10:

AR-10 Left Side Charge Handle

Been making my own buffers lately, trying different ideas, but no pictures yet
Link Posted: 2/10/2021 11:52:37 AM EDT
[Last Edit: 2/10/2021 11:53:30 AM EDT by AeroE]
Top Top