User Panel
Posted: 5/29/2006 1:28:56 PM EDT
[Last Edit: Molon]
Hornady 5.56 TAP T2 versus TAP FPD
For this article I compared Hornady’s 75 grain 5.56mm TAP T2 round to their 223 Remington 75 grain TAP FPD (For Personal Defense) round. The TAP FPD comes in a “black box” and uses “black nickel” plated cases. The TAP 5.56mm comes in a “red box” and has brass cases with crimped primers and uses the new “T2” 75 grain bullet. Both bullets have a cannelure and both rounds have a crimped case neck. The ammunition. The cartridges. The headstamps. Note the 5.56 round has a crimped in primer. The 5.56mm TAP uses "temperature stablized" ball powder... ...and the TAP FPD uses a short cut extruded powder. The bullet on the left is a virgin 75 grain BTHP sold as a reloading component. The bullet in the center is pulled from a TAP FPD round and the bullet on the right is the new “T2” bullet pulled from a round of the 5.56mm TAP T2. I asked Dave Emary (Chief Ballistician for Hornady) about the redesign of the ogive on the T2 bullet. Here was his reply: “We made the ogive radius shorter, makes the ogive a little fatter, on the TAP load because testing showed it fed better in the M16/AR." 5.56mm T2 While the original 5.56 TAP was loaded in “Frontier” head-stamped cases, the load now comes in "Hornady" head-stamped brass. In interim years, the 5.56 TAP T2 has also been seen loaded in Lake City and Winchester cases. The original lots of 5.56 TAP did not have sealed primers. When Hornady did started sealing the primers, it was reported that this sealant was a new “anaerobic” type. It had a distinctly “rubbery” feel to it as compared to traditional lacquer type sealants. The primer sealant used in one of the later lots of 5.56 TAP that I've tested appears to have a different consistency than the original sealant used. Contrary to internet myths and even Hornady promotional material, for years after its introduction, 5.56 TAP did not have sealed case mouths. Sealant at the case mouth on 5.56 TAP has been a relatively recent development. I first noticed it with lot #3071004 and oddly, I've noticed some lots after that one that didn't have the case mouth sealant; go figure. ..... Since its introduction, Hornady TAP FPD ammunition has been loaded in black-nickel coated cases. According to Hornady these “revolutionary” cases “eliminate the potential for corrosion and improve feeding in all firearms.” In 2009, Hornady began loading the TAP FPD ammunition in “revolutionary” silver-nickel coated cases and according to Hornady these cases “eliminate the potential for corrosion and improve feeding in all firearms.” Hornady also states that these newest cases “are easier to see in low-light conditions and when checking for loaded chambers.” ..... Velocity Chronographing was conducted using an Oehler 35P chronograph with "proof screen" technology. All strings of fire for this report consisted of 10 rounds each unless otherwise noted. All of the velocities listed in this report are MUZZLE velocities and were calculated from the instrumental velocities using Oehler’s Ballistic Explorer software. The three different barrels used in testing were: A Colt 14.5” M4 barrel A Colt 16” light weight profile barrel A Colt 20” government profile barrel All of the barrels used are chrome lined, NATO chambered and have 1:7” twists. Here is a table showing the muzzle velocities of each load from each of the three different barrels, along with a column showing the difference in velocities between the two loads. Attached File Atmospheric Conditions Temperature- 84 degrees F Humidity - 53% Barometric pressure – 30.02 Elevation- 960 feet above sea level Winds – variable Skies – partly cloudy, Jupiter aligned with Mars The Hornady 75 grain bullets are considered to have a fragmentation threshold of 2200 fps +/- 50 fps. Based on the conservative figure of 2250 fps the table below shows the range (in yards) at which fragmentation can be expected to occur for the two loads being tested. It also shows the gain (in yards) before reaching the fragmentation threshold for the 5.56 TAP load. VelocityUpdate Velocities of the various 5.56 TAP lots have remained remarkably consistent over the years. I still had a few boxes of each lot of 5.56 TAP that I had tested over the last 2½ years, so I decided to fire 10 rounds from each lot over a chronograph in back-to-back fashion. Seven different lots were tested using an Oehler 35-P chronograph with “proof screen” technology. The rounds were fired from a 20” Colt M16A2 government profile barrel with chrome lining, a NATO chamber and a 1:7” twist. All velocities listed below are muzzle velocities, as calculated from the instrumental velocities using Oehler’s Ballistic Explorer. None of the lots tested had an average muzzle velocity that varied more than 0.61% from the grand average muzzle velocity of 2808 fps and most of the lots varied significantly less than that. .... Accuracy Results - part 1 Normally when attempting to determine the accuracy (technically the precision) of a particular load, I use one of my stainless steel Krieger barrels for testing. However, since part of this test involves the 5.56 TAP round loaded to NATO pressures, I was just not willing to risk pressure issues from firing a NATO pressure load through one of my match chambered, tightly rifled Krieger barrels. I could have used a Krieger barrel for the SAMMI pressure 75 TAP FPD load and a different barrel for the 5.56 TAP load, but I felt this would have given an unfair advantage to the TAP FPD. Therefore I decided to test both loads from a NATO chambered barrel. What I was most interested in gleaning from this test was the relative accuracy of the two loads compared to each other anyway. It has been my experience that NATO pressure loads tend not to shoot as accurately as loads that are downloaded by 150 to 200 fps (depending on the bullet weight.) I have a 20” Colt HBAR with a 1:7” twist that shoots relatively well for a factory barrel that is chrome lined and NATO chambered. The barrel is free floated and is capable of shooting 10-shot groups from 100 yards that hover right around one inch. All shooting for this test was done at 100 yards from a benchrest with the rifle resting on front and rear bags. (Remember, I’m trying to test the accuracy of the ammunition and not particularly my shooting skills.) As a control for this test, before firing the TAP ammunition, I obtained three 10-shot groups using Sierra 77 grain MatchKings. The three 10-shot groups using the Sierra 77 grain MatchKings measured: 1.05” 1.07” 1.10”. (In an effort to reduce the human error involved in this test, I actually fired four 10-shot groups of each factory load and used the best three for analysis.) Now here’s the good part. I obtained three 10-shot groups of the Hornday 75 grain TAP FPD load and the three groups measured: 1.08” 1.15” 1.18”. Next I overlayed the three 10-shot groups from each load on each other using the RSI Shooting Lab software program and obtained 30-round composite targets for each load. The mean radius of the 77 SMK control load measured 0.32” and the mean radius for the 75 TAP FPD load measured 0.37”! I consider this to be excellent accuracy for a factory load, especially from a chrome lined, NATO chambered barrel. (See this thread for an explanation of the “mean radius.”) .... Accuracy Results – part 2 Proceeding in the same manner as described in part 1, I conducted an accuracy evaluation of the 5.56 TAP load. Remember, all groups fired consisted of 10 shots each and were fired from 100 yards from a bench rest. For this portion of the test, I fired a 10-shot group using the control load with the Sierra 77 grain MatchKing that measured exactly 1.00”. This is the smallest group obtained with the control load, with the largest being 1.10”. This group along with the three groups fired in part 1 of this test gives us four 10-shot groups of the control load fired from 100 yards that have an extreme variance of only 1/10th of an inch! (1.00”, 1.05”, 1.07”, 1.10”) I think this gives a pretty good indication of the capabilities/limitations of the barrel being used for testing and did not think that any more control groups were necessary. Now for the really good part. I obtained three 10-shot groups of the 5.56 TAP load that measured: 1.16” 1.38” 1.45”. For comparison the three 10-shot groups of the TAP FPD load from part 1 of the test measured: 1.08” 1.15” 1.18”. I compiled a 30-round composite target from the 5.56 TAP groups and measured the composite mean radius. The mean radius for the 5.56 TAP load was 0.46" while the mean radius for the TAP FPD load was 0.37". While the 5.56 TAP load is clearly not quite as accurate as the TAP FPD load (and we are only talking about a difference of 0.37” from the smallest FPD group to the largest 5.56 group at 100 yards in this test), I think the 5.56 load shows excellent accuracy for a NATO pressure load. As I stated earlier, it has been my experience that NATO pressure loads do not shoot nearly as accurately as loads that run 150-200 fps slower. ...... 5.56 TAP T2 Terminal Ballistic Test Results Testing by DocGKR shows that Hornady's 75 grain 5.56mm TAP T2 load continues to have some of the best terminal ballistic properties of any non-barrier blind 5.56mm/223 Remington load currently available. Here's a quote from Dr. Roberts on the Hornady load: "The Hornady 75 gr was the most impressive loading in bare gel––even more so than the numbers illustrate and it was extremely consistent..." Hornady 5.56 mm 75 grain T2 TAP OTM Velocity: 2689 fps from a 16" 1:7” twist barrel penetration in bare ballistic gel: 13.8" neck length: 0.8” Maximum temporary cavity: 4.3” at a depth of 4.7” Recovered diameter: 0.40” Recovered length: 0.25” Recovered weight: 30.5gr Percentage of fragmentation: 59% ........... ........... |
|
|
Excellent work, Thanks for the data. |
|
|
Well informative, You did a exellent job comparing.
|
|
|
Thanks for the info! Excellent work, BTW!
|
|
-- Freedom isn't free.
--Democracy: when 3 wolves and a sheep vote on what's for dinner. كافر |
Ammo FAQ: www.ammo-oracle.com
(Old) Mag FAQ: magfaq.tripod.com Barrel? Go CHROME or go home. |
+1! |
||
Women are not laying in the tub right now letting the water hit the pink parts dreaming about a gun nut who's playing Rainbow Six in his mom's basement. You follow?
|
All good information that correlates fairly well with my testing in 20" and 16" weapons. One correction, however, is that the fragmentation lower limit on the 75gr hornady bullet is 2200fps, not 2300fps. That's good for another 40-50yards.
|
|
|
Thanks for your reply. What is your source for the 2,200 fps fragmentation threshold? Molon |
||
|
Thanks for the great post!
|
|
"If it bleeds, we can kill it!"
|
When Hornady sent me their brochure it showed effective ranges for their various loads. The effective range for the 75gr looked like it corresponded to around 2200fps.
I also found this while searching the web. http://www.tacticalforums.com/cgi-bin/tacticalubb/ultimatebb.cgi?ubb=get_topic;f=78;t=001101#000001 |
|
|
EXCELLENT work Molon and thank you for taking the time to share it with us. First class write up all the way. And yes that is my post on tacticalforums and yes it is accurate.
|
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Superb analysis! Well done!!!
AC |
|
|
According to your post on tacticalforums the fragmentation threshold is "2200fps +/- 50fps for manufacturing variances." Being the conservative individual that I am, I am going to go with the "+50 fps" and post a table using 2,250 fps as the fragmentation threshold. Thank-you greatly for the information. Molon |
||
|
Actually, I should be clear. At the time I responded to the OP, I was unaware their 5.56mm ammunition used a different bullet (the T2). I thought it was the same projectile I had always shot loaded to higher pressures. The 2200fps +/- 50fps figure I got from talking to Hornady reps was regarding their Hornady TAP Red Box 75gr .223 pressure (same projectile as used in TAP FPD). However, I reviewed the test data I have on Hornady TAP 75gr 5.56mm T2 and their claims for maximum performance range and it is the same for a given velocity.
For instance: Hornady TAP 75gr Red Box .223 pressure from a 20" barrel: Hornady's data: 2663fps, claimed max performance range 225 yards Hornady TAP 75gr 5.56mm T2 from a 14.5" barrel: Hornady's data: 2667fps, claimed max performance range 225 yards It is possible that the BC for the T2 projectile is slightly lower (it appears less aerodynamic to me anyway but this is only an eyeballed guess and you know what those are worth) but also has a slightly lower fragmentation floor to compensate. Although, I kind of doubt it. I'm pretty sure DocGKR would've spanked me if the data was wrong. Also, as for the BC of the "non-T2" (does it even have a name? T1?) 75gr projectile, you may want to consider my comments in this thread: www.ar15.com/forums/topic.html?b=3&f=16&t=282084 I personally don't believe their claim of .390 BC for the current 75gr projectile used in their .223 pressure load. More like ~.340. ETA: When I use your numbers (environmental, BC of .389/.350, velocity) in my ballistic calculator I'm consistently reaching 2300fps 8-14 yards further than where you are hitting 2300fps. Not saying my ballistic calculator is more right than yours, just wanted to add that bit of info. |
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
In another one of Rick Jamison's excellent articles in Shooting Times, he posted the results of his testing of the Black Hills 75 grain OTM load. He chronographed SIX 10-shot groups at 200 yards and determined the ballistic coefficient for each group. The overall average BC for all six groups was .352. This is incredibly close to the BC of .350 that I used for the T2 bullet.
The BC of .389 for the TAP FPD bullet does seem a little generous. Until I can do some long range chronographing of the TAP rounds (or someone else does and posts their results) I think I'll stick with these ballistic coefficients and use the more conservative fragmentation threshold of 2,250 fps. (Table to follow) |
|
|
It also shows how consistent Hornady's TAP ammo is. As of late, even their lot-to-lot variation is damn near, if not, nil. IMO, Hornady TAP ammunition is hands down the best factory loaded ammunition .223/5.56mm I have ever used. I don't use the FPD hardly at all though so I can't comment on it as far as consistency. I don't like the black nickel coating. I know it is probably a harmless non-issue but it appears to chip off during the firing cycle and I just don't like that when I can get the red box. Other than that what experience I did have with it was good, very accurate and shot to the same POI as the Hornady TAP 75gr Red Box .223 pressure. I also wanted to add to my comments that this write up is missing NOTHING that I can see or think of at this time. Everything is foot noted where it should, detailed environmental conditions are given, etc. I'm a real stickler for that kind of thing. You are certainly to be commended for the quality of your work. My own notes are often messy because I have so much crammed in to one day of testing, but they are detailed and atleast I can read them just fine. |
||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Nicley done. Thanks for putting all of that together.
|
|
|
My first +1. Fantastic post, nice job on the layout, very easy to read and follow. |
||
When the going gets tough...the tough go cyclic.
|
I believe I found that article by Rick Jamison you referenced. It is indeed a good article, thank you for the lead.
www.shootingtimes.com/ammunition/bh_080305/index.html Notice the 80gr projectile is the only one that even comes close to a BC of .390. Personally I'd use the average BC of .353 for the Hornady 75gr "T1" for both projectiles for now. I know the barrel the projectile is fired from and the velocity at which it travels effects the BC of the projectile (all barrels mark and launch the bullet differently) but it shouldn't be too much difference and .353 is a hell of a lot closer to the real mark than .390 IMO. ETA: He used a Krieger 1:8 match barrel for his tests of the BH 75gr load which had a muzzle velocity of 2744-2834fps. On average, a standard grade 4140, 4150, CMV, etc. chrome-lined barrel will mark and deform the bullet to a greater extent and lower the BC even more. In other words, his BC measurements are likely to even be a best-case-scenerio BC measurement. |
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
It is my understanding that much like M193 traveling through the 2700 to 2500 fps range that the Hornady 75 grain OTM bullet fragment violently at 2300 and above and fragment less (can still break at cannelure) and with less reliability down to 2100 fps. This would be an average of 2200 fps for a performance envelope. Right?
What range was the chrono measurement taken at? Did you add that range back to the fragmentation range when you gave it or jaust base it off the chrono speed minus velocity lost at range? Where did you get the BC for the T2 bullet? EDIT: I SEE NOW ITS JUST A GUESS... does Hornady not have the BC info for the projectile? Are you brave enough to put your chrono out at 100 yards and take some measurements? |
|
|
Where did you get this data? I know in other calibers with high velocities and thin jackets people will NOT use cut rifled barrels because they will cause enough jacket damage to casue the projectile to break up. So your claim is just the opposite of what I have heard from some other long distance shooters. I am just repeating what I heard so I wondered whre the data comes from/what the real truth is. |
||
|
My understanding is this.. The reliable fragmentation floor is 2200fps +/- 50fps for manufacturing variances. This means all will _reliably_ fragment at 2250fps, but some lots may fragment reliably down to 2150fps. When the velocity is lower than, but relatively close to the reliable fragmentation floor, whatever it may be for that lot, fragmentation is possible, but a crap shoot (unpredictable). I suspect by manufacturing variations they mean the exact composition of the copper jacket, the lead core, jacket thickness, cannelure depth, exact gel calibration, what the individual barrel does to the bullet, etc. All of these things have tolerance ranges and vary atleast a little. If you had one lot with all the tolerances stacked in one direction and another lot with all the tolerances stacked in the other direction I could see how there could be a 100fps range of variation in reliable fragmentation floor. Match projectiles even vary in weight by a tiny fraction of a grain here and there. I am aware of some testing on the Nosler 77gr in which it fragmented as low as ~2050fps but it was not considered a reliable fragmentation floor because it was not tested across multiple lots and not more than a few times at velocity. ETA: We must also remember that the whole 2200fps +/- 50fps figure almost definitely follows a Gaussian distribution where, for example, 80% of the lots are actually something like 2200fps +/- 25fps, but the remaining 20% stretch the figure to 2200fps +/- 50fps. In construction/manufacturing actual far-end to far-end variances are relatively (<-key word) uncommon and variable items (such as jacket thickness or the thickness something must be machined to, etc.) are somewhere in the middle 25%-75% of their tolerance range a majority of the time.
He said he did add the velocity difference back to his muzzle velocity. I don't know about the fragmentation range. Maybe that's why I am getting 8-14 yards further on the fragmentation range on my ballistic calculator using his numbers (me starting with his muzzle velocity, him starting with his chrono'd velocity)? It could just be differences in the calculators' algorithms though. Hornady does have their claimed BC info for the Hornady T2 bullet, it is listed in their LE catalogue. |
|||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Also just repeating what I've heard quite awhile ago, but FWIW I did hear this from a knowledgable match grade barrel maker. I've talked to a handful over the years and I don't recall who it was that said that. I know there is a conflict of interest here but none that I've talked to are known to be liars. After seeing some bore scopes of true match grade barrels vs. standard grade for myself, I can definitely believe it. Up close one's interior is smooth as glass the other looks like the Colorado rockies by comparison. |
|||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Im not talking match vs milspec I am talking cut vs button rifled. Example... Which deforms the bullet less, a single cut Krieger or a button rifled PacNor?
|
|
|
Excellent post, thanks for sharing this info!
|
|
After all the B.S. is said and done perhaps all I can say is Molon Labe!!!
|
The ballistic coefficients that I used were not “guesses.” As stated in my first post, they were estimations extrapolated from Hornady’s ballistics tables. For example, Hornady gives the following information in their ballistic table for the 75 grain TAP FPD round.
Muzzle velocity: 2790 fps Zero: 200 yards Trajectory at muzzle: -1.5” (height of sights above the bore line) Trajectory at 300 yards: -8.30” Since no atmospheric conditions are given I used the “Standard Atmospheric Conditions” for ballistics.* Punching the first three data points into an exterior ballistics calculator program and adjusting the ballistic coefficient until the trajectory matches -8.30” at 300 yards yields a ballistic coefficient of .389. *Stand Atmospheric Conditions for ballistics. Altitude: Sea level Barometric pressure: 29.53 inches Hg Temperature: 59 degrees F Relative humidity: 78 percent |
|
|
Thanks for the great report, I didn't realize the two types were that different. I thought it was mostly a marketing thing.
|
|
T-$
|
I just got off the phone with Hornady and they said that according to an employee named "Dave," who they stated designed the new "T2" bullet, the ballistic coefficient for the T2 bullet is .361.
|
|
|
Just what I have been looking for, Thanks
|
|
|
More good informatin Molon, thank you again. If you want conservative estimates of fragmentation range, personally I'd use the .350-.353 BC for both loads and 2250fps as the fragmentation floor cut off. My understanding is the Hornady 75gr and Nosler 77gr projectiles display much more consistent distance before initial yaw than either M193 or M855 which can indeed be quite variable within a given projectile, let alone the fact that I've seen multiple different incarnations of both (meaning heavy naked-eye-visible differences) depending on the manufacturer of the bullet. Even the projectiles used in Winchester's Q3131 and Q3131A loads, which are supposed to be "identical" have glaring visible differences.
I understand your reservation about posting fragmentation range estimates. On top of what you listed there are other variables. Muzzle velocity is effected by the type of chamber, how used the barrel is, ambient temperature, suppressed or unsuppressed, lot-to-lot variation in ammunition, etc. Environmental conditions such as low humidity, high barometric pressure, etc. destroy the projectiles ability to hold velocity and hurt fragmentation range . IMO, the best you can do is use the conservative BC, fragmentation floor, your velocity numbers and standard conditions. At that point it will be up to others to adjust for the velocity their particular barrel puts out and their environmental conditions. |
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Stay tuned! |
||
|
Oops, sorry DevL. I should've read closer. Well you have me there, I don't know. This is the first time I've ever heard that Krieger (or other cut-rifled) barrels in certain calibers are unsuitable for use with thin jacketed match bullets. I'm not even close that echelon of shooters, nor am I willing to dedicate the time or $ to get there, so I stay in the mil-std kiddie pool for the most part. I don't know all the benefits and draw backs to cut-5R-polygonal-superfreak rifling. |
||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
It just bothers me that ammo makers will sell a load called for personal defense, that is less than the military/police application ammo out there.
TXL |
|
The US immigration law should mirror the Mexican immigration law. Let's see someone call that unfair, and not look stupid.
|
I just realized that even this is flawed as you are not going to get the same MV out of your barrel at 59*F that you do at 84*F. But I can't think of a better way to do it and it should be close enough. Both TAP versions are pretty temp stable and someone else's barrel might get a higher/lower MV at a given temp than your barrels so the data will never line up perfect for everyone anyway. |
|||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Right on!
My calculator gave the exact same results this time. |
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
That was the frag chart I was expecting to see. I do find it odd the regular and T2 have identical BC...
|
|
|
Well Hornady claims the T2's BC is .361, but they also claim the standard 75gr is .395 or there abouts which it is not. Better to be a little conservative when estimating fragmentation range.
|
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Very nice Molon. Awesome information, presentation and pictures.
Can we get this thing tacked please?!?!?! Scott |
|
|
Ok, here's Hornady's info/data for the 5.56mm 75gr T2 ammo:
====================================================================== + Ammunition conforms to 5,56 M855 ammunition and propellant specifications for case mouth and port pressure in an M4A1 system. + Ammunition uses a crimped in Mil-spec No41 primer. Primer push forces meet or exceed M855 specification + Ammunition is loaded with the proven Hornady 75gr BTHP bullet. The bullet is cannelured and both bullet push and pull forces meet or exceed M855 specification. Bullet has a unique ogive shape to facilitate reliable feeding. + Ammunition retains Hornady's proven match accuracy, with a factory specification in a 20" 1-7" twist 5.56 test barrel of less than 1 moa. CAUTION: THIS AMMUNITION IS MEANT ONLY FOR WEAPONS CHAMBERED IN 5.56 x 45mm NATO 14.5" Barrel Muzzle = 2660 50yds = 2535 100yds = 2413 200yds = 2180 300yds = 1960 16" Barrel Muzzle = 2720 50yds = 2593 100yds = 2470 200yds = 2234 300yds = 2011 ====================================================================== Interestingly, no data was provided for a 20" barrel. Have fun..... |
|
|
Excellent information! Thank-you. According to those numbers the bullet has a ballistic coefficient of .355 throughout the 300 yard range. |
||
|
And again there's Rick Jamison's testing that shows the T1 has a BC of .352 and now the data supplied by SOSNBA shows that the T2 has a BC of .355. Another interesting point from Rick Jamison's article is that his testing shows the 77 grain Sierra MatchKing has a BC of .340. |
||
|
Yep!
The 77gr SMK's BC was a suprise to me too, I thought it would be higher. |
|
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Is there any info on the fragmentation of the 75gr OTM without a crimp grove? I ask because I have been able to easily reach 2650fps from my 16" barrel with my own loads (I can reach 2680 but that starts showing bad signs). I see no reason to adopt the TAP FPD round if it going to fall 120fps below what I can produce. My only reservation is that I have not seen fragmentation data for the BTHP bullet they list at 75gr.
I wonder if the T2 profile will be availible to handloaders? |
|
|
I sent an e-mail to Hornady asking them that very same question. They never replied. |
||
|
Yes, it fragments just as readily. Sure the cannelure weakens the jacket more but it is a very thin jacket already so it is not necessary. Infact a years ago the first Hornady TAP 75gr I shot did not use a cannelured bullet. The cannelure was only added later. The test data I have for both the cannelured and uncannelured Hornady 75gr are indistinguishable.
Hornady TAP FPD uses a brand new case. Even with a once fired case you are playing the odds that you get a case that might've been weak to start with, and then was fired in a rifle that stresses cases more than average. Now, I know failures in once fired brass are one in a million, usually brass can take many loadings, but they do happen, I've seen it. Second, the expense of adding a cannelure was done out of necessity, not luxury. The same reason the military requires a cannelure. Some say it is not necessary if you have enough tension on the bullet. I've had some BH 75gr back before they put a cannelure on it that was extremely tight, it was incredibly difficult to pull the bullet. Once I got it out, there were obvious signs the bullet had been really squeezed in there. But I'd pick up another round out of the same box and could still push it into the case a lot easier than a cannelured round out of another. It is true that you are unlikely to have a problem, but even great neck tension is not always enough especially when you have to load for a variety of guns which all vary in their function and the conditions they will be put under. For reliability, the cannelure beats neck tension alone. The third consideration is this. Notice the TAP FPD does not use a crimped primer.. because it is only .223 pressure and is highly unlikely to pop a primer. Once you start loading to 5.56 pressures though, a crimped primer becomes more important as the likelyness of popping a primer increases dramatically. Hence the reason the 5.56mm TAP has gone through the extra step to have the primer crimped in place. I am not knocking your hand loads. There are advantages to hand loading, as you can tailor the load precisely to your gun. I bet they are great and extremely accurate, but there are often other trade-offs/limitations as to what a civilian is able to produce on his/her own compared to the machines and materials the factories have at their disposal.
I wouldn't hold your breath. |
||||
You should never try to solve your problems with handguns. Large caliber automatics work much better.
|
Thanks for the info on fragmentation. I appreciate that. Three points to address. 1.) I never use once fired brass for these loads. Only new or pulldown milsurp. I do it for exactly the reason you stated. Max loads in unknown brass is not something I do. 2.) The loads I'm shooting are within SAMMI spec. Hornady may choose to load to a certain pressure and not above with what they use for powder, but I'm not exceeding SAMMI loads in those 2650fps rounds. They are stiff but I don't think they quite hit 5.56mm land. I have been able to get over 2700fps but not without pressure problems with any powder I have on hand. Thus I backed down to 2650. It takes a good bit more pwder to get to 2700 than people may think due to diminishing returns as pressure starts to increase. 3.) These are crimped using the Lee crimp die. It crimps enough to create a very slight ring in the bullet and makes it VERY difficult to set the bullet back. I developed this load with a crimp so I know that IS the velocity with the crimp mentioned. Not ideal for accuracy but I wanted it to have the crimp. The only feature I feel uncomfortable with is the primer crimp. As a maximum load these do expand the pocket but I've never had one feel loose, back out or pop out completely. |
|||||
|
TAG
|
|
Those who give up liberty for the sake of security deserve neither liberty nor security.
--Ben Franklin |
More tid-bits.
The average case weight of the 5.56 brass is 97.2 grains. The average case weight of the FPD brass is 97.1 grains. The 5.56 TAP has a powder charge of 24.6 grains of ball powder. The TAP FPD has a powder charge of 23.6 grains of extruded powder. |
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.