Site Notices
11/24/2014 4:59:23 PM
Author
Message
SilentDeath12886
Offline
Posts: 603
Feedback: 100% (51)
Posted: 8/24/2013 4:00:48 PM EST
I have a Savage Model 11 Hog Hunter. Recently replaced the stock with a B&C medalist and now looking for bottom metal options. I prefer to keep a factory bottom metal due to price as this is more budget oriented so not really interested in dropping $250 for just the DBM plus inletting. I know CDI has bottom metal for my 4.40" Savage, but it is roughly $250 for the DBM plus $75+ for the AICS mags. So I am not interested in that route.

I don't care if its a hinged floor plate or detachable mag system, as long as its factory. I am not a huge fan of the blind magazine. Where can I find factory bottom metal? I had no luck on Brownells or Midway. Any other places I should check out?
cpwomack
Member
Offline
Posts: 151
Feedback: 100% (25)
Link To This Post
Posted: 8/24/2013 4:07:23 PM EST
Check Sharpshooter Supply, they have what you need.
SilentDeath12886
Offline
Posts: 605
Feedback: 100% (51)
Link To This Post
Posted: 8/24/2013 4:31:10 PM EST
[Jump To Reply]Originally Posted By cpwomack:
Check Sharpshooter Supply, they have what you need.


Awesome thanks! Great that it is only $50 for inletting at well!
z71rat
Offline
Posts: 1128
Feedback: 100% (8)
Link To This Post
Posted: 8/24/2013 7:57:35 PM EST
You can also get the bottom metals directly from Savage through their parts finder. $89 for the assembly, the last time I checked.

DK
SilentDeath12886
Offline
Posts: 607
Feedback: 100% (51)
Link To This Post
Posted: 8/25/2013 6:14:49 AM EST
[Jump To Reply]Originally Posted By z71rat:
You can also get the bottom metals directly from Savage through their parts finder. $89 for the assembly, the last time I checked.

DK


Just took a look, but it will not source the bottom metal since my M11 hog hunter did not have any bottom metal. It is only finding parts that came factory with my rifle.
RFutch
Get off the bench!
Offline
Posts: 5503
Feedback: 100% (26)
Link To This Post
Posted: 8/25/2013 4:11:31 PM EST
"You know what I think, don't really matter what I think. Once that first bullet goes past your head, politics and all that shit, just goes right out the window." -Hoot
mustangfreek
Member
Offline
Posts: 685
Feedback: 100% (120)
Link To This Post
Posted: 8/25/2013 11:37:11 PM EST
Tagged for info.

I recently picked up a savage 10t from cabelas with a factory DBM,accustock,etc. Now looking for a good bufget oriented stock to replace the OK at bet hollow feeling accustock.I would like to keep the DBM setup but am not sure what to use with a Bell and carlson stock or if i am really stuck ponying up for a stock liek a manners..

that link above for the savage bottom metal from pacific tool looks interesting but no info on it that i can find.
SCW
Member
Offline
Posts: 2235
Feedback: 100% (6)
Link To This Post
Posted: 8/26/2013 7:19:18 AM EST
[Jump To Reply]Originally Posted By mustangfreek:
Tagged for info.

I recently picked up a savage 10t from cabelas with a factory DBM,accustock,etc. Now looking for a good bufget oriented stock to replace the OK at bet hollow feeling accustock.I would like to keep the DBM setup but am not sure what to use with a Bell and carlson stock or if i am really stuck ponying up for a stock liek a manners..

that link above for the savage bottom metal from pacific tool looks interesting but no info on it that i can find.



I did the inlet on my B&C stock for the factory bottom metal. Unfortunately the stock is slightly deeper (taller?) at that spot than the factory, so the metal had to be recessed slightly to get it to work. But it does work very well. Just take your time, I put it into a mill so that the aluminum pillars would be cut perfectly flat then trimmed the final stages by hand and with a Dremel ().
z71rat
Offline
Posts: 1129
Feedback: 100% (8)
Link To This Post
Posted: 8/26/2013 1:31:51 PM EST
[Jump To Reply]Originally Posted By SilentDeath12886:
Just took a look, but it will not source the bottom metal since my M11 hog hunter did not have any bottom metal. It is only finding parts that came factory with my rifle.


You are more than welcome to use my serial number if you like. It will give you a matte black, short action, centerfeed.

DK
SilentDeath12886
Offline
Posts: 610
Feedback: 100% (51)
Link To This Post
Posted: 8/26/2013 4:12:45 PM EST
[Last Edit: 8/26/2013 4:13:13 PM EST by SilentDeath12886]
[Jump To Reply]Originally Posted By z71rat:
Originally Posted By SilentDeath12886:
Just took a look, but it will not source the bottom metal since my M11 hog hunter did not have any bottom metal. It is only finding parts that came factory with my rifle.


You are more than welcome to use my serial number if you like. It will give you a matte black, short action, centerfeed.

DK


Cool thanks! I am going to try to source my part from SSS since they have the DBM set at $68. But if they don't get back tome in a reasonable time, I may just pick it up from Savage then.

I inquired PTG about their DBM and seeing what their price points are as their Rem M700 DBM are very competively priced. Though I would prefer the lower profile DBM from the factory DBM.
RFutch
Get off the bench!
Offline
Posts: 5507
Feedback: 100% (26)
Link To This Post
Posted: 8/26/2013 4:40:05 PM EST
[Jump To Reply]Originally Posted By SilentDeath12886:
Originally Posted By z71rat:
Originally Posted By SilentDeath12886:
Just took a look, but it will not source the bottom metal since my M11 hog hunter did not have any bottom metal. It is only finding parts that came factory with my rifle.


You are more than welcome to use my serial number if you like. It will give you a matte black, short action, centerfeed.

DK


Cool thanks! I am going to try to source my part from SSS since they have the DBM set at $68. But if they don't get back tome in a reasonable time, I may just pick it up from Savage then.

I inquired PTG about their DBM and seeing what their price points are as their Rem M700 DBM are very competively priced. Though I would prefer the lower profile DBM from the factory DBM.


Did they give you a time frame?
"You know what I think, don't really matter what I think. Once that first bullet goes past your head, politics and all that shit, just goes right out the window." -Hoot
mustangfreek
Member
Offline
Posts: 687
Feedback: 100% (120)
Link To This Post
Posted: 8/26/2013 5:57:07 PM EST
Op, are you saying your gonna try the rem 700 bottom metal on your savage?
Cyclic
Member
Offline
Posts: 1962
Feedback: 100% (9)
Link To This Post
Posted: 8/27/2013 3:26:26 AM EST
You just need a serial number from a rifle that has the DBM you want, and order it direct from Savage. Easy. I'd go factory DBM, which gives you a detachable mag and several options. For the magazine, you will need to add the floor plate to the internal magazine parts you already have that came in the Hog Hunter. Then for extra mags go Dark Eagle, they have extended mags that fit the factory DBM.

SilentDeath12886
Offline
Posts: 612
Feedback: 100% (51)
Link To This Post
Posted: 8/27/2013 3:56:11 PM EST
[Last Edit: 8/27/2013 3:58:49 PM EST by SilentDeath12886]
Originally Posted By RFutch:
Did they give you a time frame?


No reply yet.

Originally Posted By mustangfreek:
Op, are you saying your gonna try the rem 700 bottom metal on your savage?


I am trying to find a factory Savage DBM to put on my Savage that has a blind magazine (no bottom access). A Rem700 DBM would not work on my Savage due to action screw spacing differences as well as other differences.

Originally Posted By Cyclic:
You just need a serial number from a rifle that has the DBM you want, and order it direct from Savage. Easy. I'd go factory DBM, which gives you a detachable mag and several options. For the magazine, you will need to add the floor plate to the internal magazine parts you already have that came in the Hog Hunter. Then for extra mags go Dark Eagle, they have extended mags that fit the factory DBM.


I prefer to use a factory DBM. SSS had extended 9 round mags and they also sell factory DBMs as well which is why I was trying to source my parts from them since I can get the DBM, extra mags, and have my BC stock inletted.
jmj540
Offline
Posts: 60
Feedback: 100% (4)
Link To This Post
Posted: 8/27/2013 7:07:58 PM EST
I have a factory BDM off of my savage 10hs H&S precision stock, 4.40 bolt spacing center feed .308 laying around, changed over to CDI system.
foreman2000
Member
Offline
Posts: 5738
Feedback: 100% (4)
Link To This Post
Posted: 9/1/2013 9:08:15 PM EST
[Jump To Reply]Originally Posted By jmj540:
I have a factory BDM off of my savage 10hs H&S precision stock, 4.40 bolt spacing center feed .308 laying around, changed over to CDI system.

I am interested if op is not

Posted Via AR15.Com Mobile
SilentDeath12886
Offline
Posts: 617
Feedback: 100% (51)
Link To This Post
Posted: 9/2/2013 5:04:59 AM EST
[Jump To Reply]Originally Posted By jmj540:
I have a factory BDM off of my savage 10hs H&S precision stock, 4.40 bolt spacing center feed .308 laying around, changed over to CDI system.


Found a factory DBM, thanks though.
Aubie1
Member
Military
Offline
Posts: 1541
Feedback: 100% (43)
Link To This Post
Posted: 9/4/2013 5:42:43 PM EST
Good luck getting anything from SSS...they have the worst CS. Buyer beware.
SilentDeath12886
Offline
Posts: 624
Feedback: 100% (51)
Link To This Post
Posted: 9/7/2013 4:15:56 AM EST
[Jump To Reply]Originally Posted By Aubie1:
Good luck getting anything from SSS...they have the worst CS. Buyer beware.


I got a reply about 2 weeks later from SSS. They said they will not be taking any stock work until January. I've decided to pick up an additional mag from Dark Eagle and have them inlet the stock.
one15
Offline
Posts: 1467
Feedback: 100% (31)
Link To This Post
Posted: 9/7/2013 11:48:51 AM EST
where did you end up finding the factory dbm?
SilentDeath12886
Offline
Posts: 625
Feedback: 100% (51)
Link To This Post
Posted: 9/7/2013 7:43:55 PM EST
[Jump To Reply]Originally Posted By one15:
where did you end up finding the factory dbm?


I have gotten a few offers on here.