User Panel
User Panel
User Panel
|
Posted: 11/6/2015 12:32:29 AM EDT
[#1]
How does this happen?
Dowel rod not working? Wondering I lubricant would help? Maybe an air nozzle? |
|
|
|
Posted: 11/6/2015 12:33:12 AM EDT
[#2]
How does this happen?
Dowel rod not working? Wondering If lubricant would help? Maybe an air nozzle? |
|
|
|
Posted: 11/6/2015 1:12:23 AM EDT
[#3]
Quote HistoryQuoted: How does this happen? Dowel rod not working? Wondering If lubricant would help? Maybe an air nozzle? <removed> this is not GD. dryflash3 |
|
|
|
Posted: 11/6/2015 2:12:35 AM EDT
[#4]
this is bad news.
if you are willing to trash the barrel, i'd say keep messing with it. if it's something you want to keep,stop now and call the gunsmith. what kinda gun? |
|
|
|
Posted: 11/6/2015 8:18:49 AM EDT
[#5]
Scrap barrel. A bullet fired into another bullet will bluge the barrel. Jacket bullets with lead cores- heat barrel in oven till lead runs out barrel. Then drive empty jackets out using brass or steel rod.
|
|
|
|
Posted: 11/6/2015 9:07:00 AM EDT
[#6]
Need to know a few things.
Caliber type of bullet(s) how far down the barrel (overall barrel length) both rounds touching or spaced out. |
|
|
|
Posted: 11/6/2015 9:26:11 AM EDT
[#7]
Quoted:
Rifle rounds. Stubborn rascals to remove to say the least. What was your solution? I would assume that barrel is done and buy a new one. |
|
|
|
Posted: 11/6/2015 10:49:50 AM EDT
[#8]
Quoted:
Rifle rounds. Stubborn rascals to remove to say the least. What was your solution? We should offer nothing until we get,... "the rest of the story." |
|
|
|
Posted: 11/6/2015 1:50:36 PM EDT
[#9]
Quote HistoryQuoted:
We should offer nothing until we get,... "the rest of the story." Wrong Quote HistoryQuoted:
Quoted:
Rifle rounds. Stubborn rascals to remove to say the least. What was your solution? We should offer nothing until we get,... "the rest of the story." Wrong Granted having the rest of the story is helpful but not always needed. Withholding help and advice is not what these forums are about. |
|
|
|
Posted: 11/6/2015 2:29:10 PM EDT
[#10]
Quote HistoryQuoted:
Scrap barrel. A bullet fired into another bullet will bluge the barrel. Jacket bullets with lead cores- heat barrel in oven till lead runs out barrel. Then drive empty jackets out using brass or steel rod. Melitng point of lead is 621 degrees or so. Most oven's wont go that high. Would using a propane torch on the barrel mess up the metallurgy? |
|
|
|
Posted: 11/6/2015 2:41:29 PM EDT
[#11]
Quote HistoryQuoted:
Granted having the rest of the story is helpful but not always needed. Withholding help and advice is not what these forums are about. Quote HistoryQuoted:
Quoted:
Quoted:
Rifle rounds. Stubborn rascals to remove to say the least. What was your solution? We should offer nothing until we get,... "the rest of the story." Wrong Granted having the rest of the story is helpful but not always needed. Withholding help and advice is not what these forums are about. Half agree... rest of story would help us give advice about whether barrel is worth saving. Not sure I believe there are two bullets in a barrel without major damage. |
|
|
|
Posted: 11/6/2015 3:29:09 PM EDT
[#12]
OP, solutions are easy to attain when your problem has been thoroughly explained. More information would be better. 
|
|
|
|
Posted: 11/6/2015 5:06:08 PM EDT
[#13]
Quote HistoryQuoted: We should offer nothing until we get,... "the rest of the story." Quote HistoryQuoted: Quoted: Rifle rounds. Stubborn rascals to remove to say the least. What was your solution? We should offer nothing until we get,... "the rest of the story." Lets not play this GD game in a Technical Forum. If OP want's help he will provide enough details so we can help him. If he doesn't come back to this thread, you have driven him away.  |
|
|
|
Posted: 11/6/2015 5:12:03 PM EDT
[#14]
personally, I would toss the barrel.
I would imagine the easiest way to remove it yourself would be to put the barrel in a vice and use a wooden dowel that moves freely within the barrel to force the bullet out of the barrel with a mallet. |
|
|
|
Posted: 11/7/2015 1:08:13 AM EDT
[#15]
Be prepared to toss the barrel if you've lodged 2. It's probably bulged.
Try filling it with oil to within a couple inches of the barrel. Take a dowel as close to barrel dia. and a tightly fitted patch and pound away. What caliber? I've got a rifle with a ringed bbl but it's not exactly a bruiser (25-20). I still shoot it. |
|
|
|
Posted: 11/7/2015 9:21:37 AM EDT
[#16]
A friend did this on a Nagant, we took a 1/4th inch brazing rod 3 ft. long
and just used gravity and a little "fling" with the muzzle pointed downward. I was turely surprised how easy it was to drive them out. IIRC it only took 10 -12 impacts. My 2 cent worth but for us it work well. sdshooter.................. |
|
|
|
Posted: 11/7/2015 9:35:16 AM EDT
[#17]
Brass dowel, and shop press "should" walk them right out
|
|
|
|
Posted: 11/7/2015 9:59:27 AM EDT
[#18]
Quote HistoryQuoted:
A friend did this on a Nagant, we took a 1/4th inch brazing rod 3 ft. long and just used gravity and a little "fling" with the muzzle pointed downward. I was turely surprised how easy it was to drive them out. IIRC it only took 10 -12 impacts. My 2 cent worth but for us it work well. sdshooter.................. Any idea how your friend did that? Were they reloads? Maybe easy to remove if using 308 bullets in a barrel made for who knows what. Lots of variation in those. |
|
|
|
Posted: 11/7/2015 1:17:43 PM EDT
[#19]
Factory new, his sons found the projo's where loose and must of
lost some powder out of one. They were hunting deer and in the heat of the chase they didn't notice the non exit of round 1 and set off round 2. I got the call that evening, the gun was checked out and found a cracked bolt; we welded it tight and holds a place of Honor as a wall hanger now. sdshooter............ |
|
|
|
Posted: 11/7/2015 2:27:41 PM EDT
[#20]
Depending on how far the two bullets are down the pipe just send the barrel to Adco to have them cut it and start the paper work on a sbr
|
|
|
|
Posted: 11/7/2015 5:22:45 PM EDT
[#21]
If the barrel does not look bulged or damaged, buy a 3 foot brass rod from your local hardware store and a couple taps on the end of the brass rod with a hammer should dislodge them fairly easily. Wrap the end of the brass rod with electrical tape as an extra precaution so you don't scratch the bore.
|
|
|
|
Posted: 11/8/2015 1:51:04 PM EDT
[#22]
Quote HistoryQuoted:
If the barrel does not look bulged or damaged, buy a 3 foot brass rod from your local hardware store and a couple taps on the end of the brass rod with a hammer should dislodge them fairly easily. Wrap the end of the brass rod with electrical tape as an extra precaution so you don't scratch the bore. You gotta remember that barrels are tight enough to leave an imprint of the rifling on the bullets. The bullets will not fall out after a couple of taps. Ive had a couple of squibs from when I first got into reloading. One on a AR barrel, one on a Glock. The glock, I handled with a brass punch and a vice. The AR barrel I did with a soft steel cleaning rod and a bearing press. I left a little Kroil in the barrel overnight as lubricant and to help work the bullets loose. |
|
|
|
Posted: 11/24/2015 11:31:05 PM EDT
[#23]
Took an extraneous amount of effort but got the barrel cleared.
A 48 ounce hammer with a steel rod wouldn't do the job. Took a relief drill cut in the base end of the first projectile to make the stoppage unstop. I don't want to try that crap again. |
|
|
|
Posted: 11/24/2015 11:55:20 PM EDT
[#24]
Did the barrel survive in shootable condition?
|
|
|
|
Posted: 11/25/2015 12:05:54 AM EDT
[#25]
Quote HistoryQuoted:
Did the barrel survive in shootable condition? Yes DF. Low pressure round started the problem. The first round stopped about 2 inches into the bore of the barrel. Found out that the 2nd round was not a round at all but a stuck brass jag that was used to remove the first stuck projo. Those two rascals made for a difficult problem. |
|
|
|
Posted: 11/25/2015 12:07:53 AM EDT
[#26]
Quote HistoryQuoted: Yes DF. Low pressure round started the problem. The first round stopped. Found out that the 2nd round was not a round at all but a stuck brass jag that was used to remove the first stuck projo. Those two rascals made for a difficult problem. Quote HistoryQuoted: Quoted: Did the barrel survive in shootable condition? Yes DF. Low pressure round started the problem. The first round stopped. Found out that the 2nd round was not a round at all but a stuck brass jag that was used to remove the first stuck projo. Those two rascals made for a difficult problem.  |
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
