User Panel
[#1]
Loaded up 50 6.5 CM with 100 gr nosler bullets over a work up (down) of reduced charges of H4895.
Hoping to find an accurate, reduced recoil, reduced powder eating, target and squirrel hunting round. |
|
"No bastard ever won a war by dying for his country. He won it by making the other poor dumb bastard die for his country." George S. Patton
|
[#2]
Hand primed 800 pcs of .45 brass.
Ordered 2000 .38 cal JSP. Began load workup for .243 w/TSX & Hunter |
|
IYAOYAS
|
[#3]
Loaded up 350 rounds of RMR 124gr FMJ's over some True Blue . It was good to get back to a larger smooth pistol session. I'm going to pull out my cheap $28 bullet feeder for the next run.
|
|
Living the CW six pack club dream.
|
The root of politics is power and money
GA, USA
|
[#4]
Sorted brass from my last range trip and resized ~200 6.5G cases that have been hanging around for a few years.
|
In the Marines I got PT Thrashed on Christmas by our Drill Instructor because he blamed the death of Christ on recruits.
-USAWTF |
[#5]
Loaded 50 6.5 creedmoor. 25 neck sized, 25 full length sized. Gonna test em out tomorrow along with some other things.
|
|
"No bastard ever won a war by dying for his country. He won it by making the other poor dumb bastard die for his country." George S. Patton
|
[Last Edit: Ronin859]
[#6]
Deprimed and tumbled 1200 pieces of 5.56.
Swagged and primed 100 to work up some loads I didn't have much luck with the first go around. The new Dillon Super Swage is night and day better than my old RCBS Swage Tool though. Worth every penny. Sorted all my 5.56 and half of my 9mm by headstamp. After that's done everything will be clean and organized, which will be nice. Went to resize some of the LC I just got and realized that my expander rod is bent to hell. I'm going to have to order a replacement... |
|
And Shepherds we shall be
|
[#7]
After shooting about 200 rounds of the 350 I made up last night. I finally got around to pulling my press and remounting on the bench with an InLine Fabrication Ultramount.
|
|
Living the CW six pack club dream.
|
Breaching your mom's mine-wire obstacle.
TN, USA
|
[#8]
|
This is why we can't have nice things.
|
[#9]
Hand primed another 1400+ of .45acp.
Analyzed my .243 loads; going to need some tweeking but i’m getting there. Tumbled approximately 2k pcs of .40 S&W. |
|
IYAOYAS
|
[#10]
Sized, swaged and trimmed my last 5 gallons of lc 223 brass.
I’m glad that’s over. Now I have to wet tumble it all. I might have to buy a extra tumbler. |
|
I love my beautiful hot wife
|
[#11]
Went to the range. Sighted in my 458 socom.
Then, tested some 6.5 CM. Results for one test are inconclusive. There is a thread on here about it. The other test went well. Reduced recoil loads for the CM were awesome. Accuracy was good. Multiple sub MOA 5 shot groups in the work up. Came home and resized all the 458 socom brass I had. Gotta go start the tumbler before I forget. Then, I annealed all the 6.5 CM brass I had shot today. |
|
"No bastard ever won a war by dying for his country. He won it by making the other poor dumb bastard die for his country." George S. Patton
|
[#12]
Loaded a pile of 7.62x54mmR...might hit the pile of 6.5x55mm tomorrow in celebration of Canadian Thanksgiving.
|
|
|
Global Warming Hoax Skeptic before it was cool
WA, USA
|
[#13]
Yesterday went shooting. Tried out new AR 9 pistol build. Successful test.
See my post in the AR 15 "Rimfire and Pistol Calibers" forum for more details. Shot over 1k between the new AR 9 pistol and the AR 9 carbine. Think I finally shot up all of my bare cast loads in 9mm. Only PC from here on out. Today I sorted the 223, 7.62x39, from the 9mm. Didn't have to sort the 357 as they went back in the plastic cartridge box. Just love the PC 158 gr home cast SWC and 10 grs of True Blue. A little lighter than a full H-110 load, but still smacks the steel. Got the steel 7.62x39 dry tumbled. Tomorrow will start deprimming and wet tumbling the 357 and 9mm. 223's belonged to NW556. |
Selling agent for Algores carbon credit scam.
Shooting and Reloading, one hobby feeds the other. |
[#14]
Did 75 rounds of 6.5x55mm for the AG42B -- I really need to shoot that rifle more.
Almost launched into some .303 British but got lazy. |
|
|
[#15]
Fully prepped and hand primed about 1k of .357mag brass.
Fully prepped 1k of .44mag brass. Loaded another set of load for my .243. Hand primed 600 pcs of .40 S&W brass/ |
|
IYAOYAS
|
[#16]
Finally got my Dillon 550 up and running for my 45 ACP reloading. I don't know how I feel about the Dillon. It has pros and cons over my Hornady LNL. I suppose I'll need more time to get a feel for it. I only loaded 200 rounds on it. Priming and resizing is definitely better on the Dillon. I think the rest goes to the LNL.
Time will tell. |
|
|
[#17]
Ordered 1K 230gr HST
|
|
IYAOYAS
|
[#18]
Harvested a bear on Saturday with my handloaded 168gr Barnes TTSX
|
|
.
|
[#19]
Loaded 300 .357mag plinking rounds.
Wet tumbled 400 .44mag cases. Labeled a few ammo cans. Bought 1K 165gr SSTs. |
|
IYAOYAS
|
[#20]
Dug out my stash of shotgun hulls so I can load some 12ga. slugs and buckshot.
I have to sort out the Win AA "old style" compression formed ones because this is the only hull I have data and components for. |
|
...behind every blade of grass...
|
Breaching your mom's mine-wire obstacle.
TN, USA
|
[#21]
I just ordered a Harbor Freight dual drum tumbler, 2.5lbs of stainless pins, a magnet and a amazon warehouse deal dehydrator to start wet tumbling finally.
|
This is why we can't have nice things.
|
[#22]
Went shopping.
4 lbs Power Pistol 10K Fed 205MAR 5 lbs RE-17 |
|
IYAOYAS
|
[Last Edit: mk4dubbin]
[#23]
ordered 400 220gr projectiles for 300blk subs
|
|
.
|
[Last Edit: SideSalad]
[#24]
Loaded 770 .357mag plinking/target rounds & 200 .44mag rounds of the same persuasion. Broke my decapping rod so I ordered a few more of those. Started gettting organized/set up to do another run of .308 for My MWS.
|
|
IYAOYAS
|
[#25]
Loaded 100 125 Gr Nosler BT's in 300 BO. Antlerless season opens this weekend.
|
|
|
[#26]
Ordered 500 pcs Win .308 brass.
|
|
IYAOYAS
|
[#27]
Annealed and neck sized some 308 and 6.5 creedmoor. Ran the 6.5 through a body die since a few were sticky on extraction. The Fix has a tight chamber. I found 1500 175 rdf bullets that I couldn't remember for sure that I ordered.
|
|
Enjoys long walks on the beach, poetry, and poking dead things with a stick
|
[#28]
Loaded 250 .44mag.
Wet tumbled last batch of .44. Continued prep work onnext run of .308 for my LMT MWS. |
|
IYAOYAS
|
[#29]
Shot a small set of 6.8 SPC reloads in my PSA 6.8 upper.
These are my first “bottleneck rifle in a semi auto” reloads. 100% functioning all rounds, ejecting was consistent and carrier locked to rear on all final rounds. Now reloading a charge ladder for accuracy testing. Using my new Hornady 6.8 seating die for these reloads. The “sleeve” in this die is a big improvement for the flat base 90 gr Nosler bullets in loading. |
|
Better, Faster, Cheaper - Pick Two!
|
Global Warming Hoax Skeptic before it was cool
WA, USA
|
[#30]
|
Selling agent for Algores carbon credit scam.
Shooting and Reloading, one hobby feeds the other. |
[#31]
A bunch of brass prep..
Ordered a 6K flat of Hornady 2266B |
|
IYAOYAS
|
[#32]
Loaded a few hundred “plinking” 45-70s with 420gr cast.
|
|
|
[#33]
I took my powder measure’s hopper off and cleaned the heck out of it. Before I start up another large loading project, I want to de-static the hopper as much as possible, and cleaning is the first step.
I started with Dawn and warm water with a brush to scrub the inside. Then I used alcohol-based hand sanitizer to clean more - the gel consistency of the sanitizer got it to stay in contact with the plastic for longer. I finished up with a rinse in isopropyl alcohol. I’m going to let it just sit and dry overnight, and I’ll paste wax the insides tomorrow or Tuesday evening. I also spent some time reading the CMP’s forums. There’s a lot of great data about loading for .30 Carbine, particularly about how the brass DOES need to be trimmed, and not just for consistency. I have a bunch of brass and bullets, lots of primers and powder, so I’m working on the details of loading a very large quantity of this stuff. |
|
"--you can't conquer a free man; the most you can do is kill him."
Heinlein NRA Life Member Glock Certified Armorer Certified AR15 Armorer Certified M1911 Armorer |
[#34]
Ordered 500 - 245gr Missouri Bullet cast/coated for my 300 BO.
|
|
I'm an enigma, wrapped in mystery, sometimes bacon.
|
[#35]
Decided to make some 300 blackout cases today the old school way and then realized I had a 1050 ..duh.
Ordered the RT1500 , tool head and trim die. I did cut 3000 pieces tho. Now I’ll wait to finish. |
|
I love my beautiful hot wife
|
Global Warming Hoax Skeptic before it was cool
WA, USA
|
[#36]
Decapped the 357 I got at the funshow and have it wet tumbling.
Started decapping the 9mm. |
Selling agent for Algores carbon credit scam.
Shooting and Reloading, one hobby feeds the other. |
[#37]
Bought:
500 Ni .44mag Starline brass 500 Ni 10mm Starline brass 200 155gr Dots 100 90gr XTP's |
|
IYAOYAS
|
[#38]
Just ordered 1000 124gr. fMJ bullets.
Spent last night separating a 5 gallon bucket of brass into desperate bins. Still have another bucket to go and two large boxes filled. |
|
I'd rather be judged by 12 than carried by 6
|
[#39]
Ran about 3000 223 crimped cases thru the 1050 to size them and remove the crimp. I've had all the handle pulling I want for a few days.
|
|
|
[#40]
Started loading again for my LMT MWS (40 rnds).
Tumbled a batch of .223/5.56 range pickup brass. Flared case mouths on approximately 400 .40 S&W |
|
IYAOYAS
|
[Last Edit: Darkhors5]
[#41]
Printed off 2 of these to hold primer tubes on the 650 support brace
If you want the STL https://www.thingiverse.com/thing:2764088 |
|
|
[#42]
Seperated a 4-5 hundred clean/deprimed .45acp cases lrg vs small primer.
Found mixed in 1 .45colt 2 . 40SW 1 .45 with a primer still in |
|
|
Global Warming Hoax Skeptic before it was cool
WA, USA
|
[#43]
Took 357 cases out of wet tumbler and replaced with a load of 9mm's.
About 3 more loads of 9mm to go. |
Selling agent for Algores carbon credit scam.
Shooting and Reloading, one hobby feeds the other. |
[#44]
|
|
I'd rather be judged by 12 than carried by 6
|
[#45]
Lots of winning in this thread
I loaded up some 200gn Barnes XPB for the 450 Bushmaster to test out as my deer load this year. |
|
The last thing I want to do is hurt you. But it's still on my list.
|
[#46]
Wet tumbled another batch off .223.
Loaded 100 more .308 rds. Sorted some brass. Resized and deprimed about 600 .40S&W. |
|
IYAOYAS
|
Global Warming Hoax Skeptic before it was cool
WA, USA
|
[#47]
Removed a batch of 9mm from wet tumbler, decapped another batch of 9mm and got it tumbling.
|
Selling agent for Algores carbon credit scam.
Shooting and Reloading, one hobby feeds the other. |
[#48]
-Loaded 180 .308 rds
-Wet tumbled 3 batches of pistol brass. -Hand primed 400 pcs .40 S&W -Loaded 50 9mm w/HSTs. -Did some more work on storage options/efficiency. |
|
IYAOYAS
|
[#49]
Recent thread here regarding H335 had me thinking my current load of 22grs is lowish for 55 FMJ.
Loaded up 10 rounds of 23grs and 10 rounds of 24grs to see how my AR like them. |
|
|
[#50]
Received my RCBS Chargemaster Lite. Going to set it up and load up 250 .223 with Nosler 60 Btips and AR Comp. I have a rifle that loves this round.
|
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.