User Panel
User Panel
User Panel
|
Posted: 1/30/2016 11:16:51 PM EDT
I am new to AKs so this may be a no biggie, but I modified my SLR107 folding stock so I could run a decent sling configuration. Coming from the AR world, I was surprised to find out I couldn't buy an aftermarket stock with a QD point on the rear for my Arsenal folder. I gained the QD point I needed just ahead of the receiver when I added the Midwest Industries keymod hand guard. A $19 Magpul MSA-QD from midwayusa and three drilled holes later, I had the QD point I needed on the rear of the stock. It sets low enough that the folding stock can still latch in to the receiver as well.
|
|
|
|
Posted: 1/31/2016 2:33:41 PM EDT
[#1]
Sweet.
|
|
|
|
Posted: 2/2/2016 7:25:28 PM EDT
[#2]
Pretty neat mod! And still folds and locks with no problem.
I'm going to have to save that to my photo collection. |
|
|
|
Posted: 2/25/2016 3:08:24 AM EDT
[#3]
Platoon-
Did you have to drill 3 holes total? Two for the screws and one larger one in the middle, into the stock for the sling to clip into? I'm trying to add a single point mount similar to that to the lower handguard on my Arsenal. Putting that on the front end will take up minimal space and work with my Magpul sling. Just trying to pick the right mount and wondering how far the sling clips into / through the mount. There isn't much room behind the handguard before the heat shield slips in there. I'll have to use some really flush nuts for the screws as it is. Thanks |
|
|
|
Posted: 2/25/2016 3:12:45 AM EDT
[#4]
If that mount requires the male end of the swivel to stick too far into the handguard and hits my heat shield I might be best using this one instead
http://www.midwayusa.com/product/349625/magpul-m-lok-qd-sling-mount-aluminum-black |
|
|
|
Posted: 2/29/2016 4:04:54 AM EDT
[#5]
Quote HistoryQuoted:
If that mount requires the male end of the swivel to stick too far into the handguard and hits my heat shield I might be best using this one instead http://www.midwayusa.com/product/349625/magpul-m-lok-qd-sling-mount-aluminum-black Might as well get the standard Magpul handguard and use that sling mount on the bottom. At least you wouldn't have to drill out your existing one. The Noveske QD mount would also work for the stock. |
|
|
|
Posted: 3/1/2016 12:17:46 AM EDT
[#6]
I put mine here it works amazing
|
|
|
|
Posted: 3/1/2016 12:53:31 AM EDT
[#7]
For now I ordered an Echo93 single point mount that goes between the pistol grip and receiver. That will go on my Arsenal
For my Egyptian Maadi I have a CNC Warrior side folder, and a steel lower handguard I ordered from Circle10 that is like a keymod type of rail. Annnnnd for my Mak90 I have a Ironwood stock set on the way. It'll be nice to have all this installed 
|
|
|
|
Posted: 3/26/2016 11:09:34 PM EDT
[#8]
Quote HistoryQuoted:
I put mine here it works amazing <a href="http://s1303.photobucket.com/user/sparks556/media/4F85DE69-04BD-4E99-8474-5012F64E4DCB_zpst7w1vuje.jpg.html" target="_blank">http://i1303.photobucket.com/albums/ag145/sparks556/4F85DE69-04BD-4E99-8474-5012F64E4DCB_zpst7w1vuje.jpg</a> How are you doing that? |
|
|
|
Posted: 4/9/2016 11:32:26 PM EDT
[#9]
Cool mod, looks great, good work!
|
|
|
|
Posted: 5/4/2016 12:34:56 PM EDT
[#10]
Quote HistoryQuoted:
How are you doing that? Quote HistoryQuoted:
Quoted:
I put mine here it works amazing <a href="http://s1303.photobucket.com/user/sparks556/media/4F85DE69-04BD-4E99-8474-5012F64E4DCB_zpst7w1vuje.jpg.html" target="_blank">http://i1303.photobucket.com/albums/ag145/sparks556/4F85DE69-04BD-4E99-8474-5012F64E4DCB_zpst7w1vuje.jpg</a> How are you doing that? Sorry forgot to answer this...pulled old sling mounting hardware... Used nice drill bit and a dremal and opened I the plastic and metal to fit a magpul qd cup. Mounted with magpuls bolt and lock washer in cup... Worked like a charm...cost like $20 I think... You can see the mounting bolt and washer I trimmed after I painted it looked almost factory... I did fill the hole with black silicone Rtv and put the qd cup in to help seal as much water put as I could...looks not bad at all I'll take a pick of the finished product for you. I did this with all my folders.. 
|
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
